help me to figure out the answer? 1. Given the logic cirenit diagram shown in Figure 1. Determine the Boolean expression for fhecircmit. Implement the expression by buildimg the circuit on the trainer. SW1, SW2, SW3 andSW4 represent A, B, C and D respectively and Y is represented by L1 LED. Comnect pin 14 znd7 to Ves (+5V) and GND respectively.Y =SW13SW2SW3LI12D.SW4DosY=?13Figure 12. Complete the Expected outour column for the Boolean expression in Table 1.Y (Shown on LI LED)D (SW4) Expectedoutput(Y)A (SWI)B (SW2)C (SW3)0.0.1.0.0.0.0.一0.0.1010.10.1.1

Since you have asked multiple question, we will solve the first question for you. If you want any…

1. Given the logic circuit diagram shown in Figure 1. Determine the Boolean expression for fhe circnit. Implement the expression by building the circuit on the trainer. SW1, SW2, SW3 and SW4 represent A, B, C and D respectively and Y is represented by L1 LED. Connect pin 14 znd 7 to Ves (+5V) and GND respectively. Y = SW1 A 4. SW2 SW3 C LI 12 11 13 Y=? SW4

1. Given the logic circuit diagram shown in Figure 1. Determine the Boolean expression for fhe circnit. Implement the expression by building the circuit on the trainer. SW1, SW2, SW3 and SW4 represent A, B, C and D respectively and Y is represented by L1 LED. Connect pin 14 znd 7 to Ves (+5V) and GND respectively. Y = SW1 A 4. SW2 SW3 C LI 12 11 13 Y=? SW4

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
Electrical Engineering Draw 2, 1 bit ALUS to create a basic 2 bit ALU. the carry out and carry in bits must ripple across. The ALU should subtract/add, logical NOR, logical AND, and logical OR. Draw out the adding logic circuit
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG
Using truth table for 7-segment logic:1. Determine the minimum logic for segment b2. Determine the minimum logic for segment c3. Determine the minimum logic for segment d4. Determine the minimum logic for segment e5. Determine the minimum logic for segment f6. Determine the minimum logic for segment g
An X-input exclusive-OR gate and a Y-input exclusive-OR gate (where X=3, Y=4 have their outputs connected to a 2-input exclusive-NORgate. Do the following:a) Draw the logic diagram and analyze the logic expression of the output (in standard SOPform).b) List out all essential prime implicants.
Write a VHDL code for the following simple logic circuit. D- X1 X2 f X3
Logic Gates:* 7404LS (NOT)* 7408LS (AND)* 7432LS (OR)* 7400LS (NAND)* 7402LS (NOR)* 7486LS (EX-OR)Or you can use 74HCxx versions. Task 2: 4 INPUT PRIORITY ENCODERa) Write the truth table.b) Find the outputs in terms of min terms using minimal expression.c) By using K map, find the simple/simplest expression of theoutputs.d) Draw the circuit diagram. (Simulation design will be accepted.)e) Simulate the circuit & explain your results. (Please do notdesign separate simulations for each output. You should design ONEsimulation including all inputs and outputs.)
Task 6: Simplifying Boolean functions in EWB using the logic converter Simplify the following Boolean expression in EWB using the logic converter F (A, B, C) = AB'C'+ A'B'C'+ A'BC'+ A'B'C
4. Figure 2 shows a logic circuit with output F Figure 2. Logic circuit with gate I (AND), gate II (AND), gate III (NOT), gate IV (AND), gate V (EXOR) and gate VI (OR) a. Find the Boolean expression of output F. b. The simplified Boolean expression of Output F. c. If the input A and C were High and Input B was Low, what is output F:
Select a suitable example for for combinational logic circuit. O a. None of the given choices O b. De-multiplexer O c. PLA O d. Latches