A 3 m deep excavation will be supported by a cantilever sheet pile. The foundation soil is dense sand, but it is assumed that the pile tip penetrates impermeable soil so hydrostatic pore pressure can be used. A surcharge of 10kPa is applied at the ground level. The water table is at the ground surface and dredge line as shown. Use Yw=10kN/m³ for your calculations. a) Using a factor of safety of 2.0 for Kp, check if D'=5m is safe or not (no need to iterate for other D'). b) Calculate the maximum bending moment. H=3.0m 1 10 kPa D'=5m? G.L. Dense sand Yt=20.0 kN/m³ D.L. 77 c'=0 Ka=0.2 Kp=6.0 Impermeable soil

A 3 m deep excavation will be supported by a cantilever sheet pile. The foundation soil is dense sand, but it is assumed that the pile tip penetrates impermeable soil so hydrostatic pore pressure can be used. A surcharge of 10kPa is applied at the ground level. The water table is at the ground surface and dredge line as shown. Use Yw=10kN/m³ for your calculations. a) Using a factor of safety of 2.0 for Kp, check if D'=5m is safe or not (no need to iterate for other D'). b) Calculate the maximum bending moment. H=3.0m 1 10 kPa D'=5m? G.L. Dense sand Yt=20.0 kN/m³ D.L. 77 c'=0 Ka=0.2 Kp=6.0 Impermeable soil

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Sheet-pile Walls

Section: Chapter Questions

Problem 18.1P: Refer to Figure 18.9. A cantilever sheet pile is driven into a granular soil where the water table...

See similar textbooks

Similar questions

A 3 m deep excavation will be supported by a cantilever sheet pile. The foundation soil is dense sand, but it is assumed that the pile tip penetrates impermeable soil so hydrostatic pore pressure can be used. A surcharge of 10kPa is applied at the ground level. The water table is at the ground surface and dredge line as shown. Use Yw=10kN/m³ for your calculations. a) Using a factor of safety of 2.0 for Kp, check if D'=5m is safe or not (no need to iterate for other D'). b) Calculate the maximum bending moment.
A circular pile 0.45m in diameter and 15m long is embedded in a layer of dense sand. The soil has the following properties: Dry unit eight is 18 kN/m3 and saturated unit weight is 21 kN/m3 (water table is 4m below from the ground surface), Nq=85, k=1.25, tan αα = 0.45 and FS=2.5 a) Calculate the end bearing capacity b) Calculate the frictional resistance c) Calculate the allowable load
Refer to Figure 18.9. A cantilever sheet pile is driven into a granular soil where the water table is 2 m (L1) below the top of the sand. The properties of the sand are =40, =17.5kN/m3, and sat=19kN/m3. It is proposed to excavate to a depth of 6 m (L) below the ground level. Determine the actual depth to which the sheet pile must be driven (L + D), using the net lateral pressure diagram. Note: Dactual=1.3(L3+L4)theory
Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
Consider a 15 m long concrete pile with a cross section of 0.45 m x 0.45 m fully embedded in sand.For the sand, unit weight, γ = 17 kN/m3 and soil friction angle, ϕ’ = 35o. Estimate the ultimate point??? with each of the following:1.1 Meyerhof’s method (Ans: 1014 kN)1.2 Vesic’s method (Ans: 1754 kN)1.3 Coyle and Castello’s method (Ans: 2479 kN)
A circular pile having a diameter of 0.33 m is 14.21 m long which is embedded in a layer of dense compacted sand having the given properties. Soil properties: Lateral pressure factor, K = 3.53 Nq = 99 Specific gravity, Gs= 2.61 Void ratio, e =1.21 Saturation above the GWT = 0.41 Ground water table (GWT) is located 3.58 m below the ground. Use unit weight of water = 9.81 kN/m3 Coefficient of friction = 0.41 Factor of safety = 3.98 Calculate the allowable capacity of the pile in kN.
Refer to Figure 9.42b. Let L = 18 m, γfill = 17 kN/m3, γsat(clay) = 19.8 kN/m3, Φ'clay = 20°, Hf = 3.5 m, and D (pile diameter) = 406 mm. The water table coincides with the top of the clay layer. Determine the total downward drag force on the pile. Assume ẟ' = 0.6 Φ'clay.
A concrete pile is 18 m long and has a cross-section of 0.406 m x 0.406 m. The pile is embedded in the sand having γ = 16 kN/m3 and Φ' = 370. The allowable working load is 900 kN. If 600 kN are contributed by the frictional resistance and 300 kN are from the point load, determine the elastic settlement of the pile. Given: EP = 2.1 x 106 kN/m2 , ES = 30 x 103 kN/m2 , μS = 0.38, and ξ = 0.57.
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2 and ?s = 0.2.
cantilever sheet pile shown. below, determine: A)the depth of embedment (d). B)the maximum moment.
A square prestressed concrete pile with a cross section 0.3 m by 0.3 m is driven 15 m into overconsolidated clays with properties as defined: From the ground surface to a depth of 7 m, the unit weight is 17 kN/m3 and the shear strength cohesion cu is 70 kPa; below 7 m, the soil unit weight is 18.5 kN/m3 and cohesion is 105 kPa. Use the total stress α-method to calculate both the design downward axial capacity and upward axial capacity, using a factor of safety of 3 (downward and upward).