Design a PLC program that will correctly execute the following industrial control process: A part is placed on a conveyor. The part automatically moves down the conveyor. In the middle of the conveyor the part goes through a two-foot-long painting section. The sprayer paints for the time the part is under the painting booth, during which time the conveyor does not stop. When the part reaches the end of the conveyor, the conveyor stops, and the part is removed. Assume that only one part can be on the conveyor at one time. Use a limit switch at the front of the painting booth and another at the end. Spray Booth (#1) or Stamper Enclosure (#2) Start Here Stops Here Define all inputs and outputs and label the PLC diagram.

Design a PLC program that will correctly execute the following industrial control process: A part is placed on a conveyor. The part automatically moves down the conveyor. In the middle of the conveyor the part goes through a two-foot-long painting section. The sprayer paints for the time the part is under the painting booth, during which time the conveyor does not stop. When the part reaches the end of the conveyor, the conveyor stops, and the part is removed. Assume that only one part can be on the conveyor at one time. Use a limit switch at the front of the painting booth and another at the end. Spray Booth (#1) or Stamper Enclosure (#2) Start Here Stops Here Define all inputs and outputs and label the PLC diagram.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter58: Programmable And Motion Control

Section: Chapter Questions

Problem 2SQ

See similar textbooks

Similar questions

List some instrumentation and controls-related research titles or topics. (Not using PLC/ARDUINO).
Department of Control and Automation Subject: Control systems Principles Hello dear, I now have a very important test, and I need to answer in a short time, less than an hour And if you give me the answer within the specified time, I will like you on your answer and invite my colleagues also and thank you
What is Adaptive control system? If the process characteristics are notwell known then what type of scheme you would suggest explain in detail thescheme and write its merits and demerits.
1.a. In a DC servo motor system, the tachometer feeds back a voltage that’s proportional to motor speed.Where does this voltage go to?A. The interpolator cardB. The CPU in the main controllerC. The driverD. The axis logic card1.b. A type of feedback device that uses a rotor and senses the position of the motor by means of sine andcosine waveforms is called a/anA. tachometer.B. encoder.C. resolver.D. alternator.
It is necessary for control system to meet certain specifications as far as its performance is concerned. Explain the methods (at least three) that can be employed to improve the time response of a control system.
A washing machine is supplied with hot and cold water from two different supplies. Draw the bock the diagram of a process control that controls the hot water flow ?? and the cold water flow ?? to adjust the water temperature as the machine user specify? and define each block? Note: pressure controlled pneumatic actuator is used as a valve.
- State the five fundamental differences between the classical control, and the intelligent control. - State the main difference between the (Fuzzy Control, Neural Net, GA).
Explain about the use of PLC in conveyor (moving material machine) and how to implement it using ladder diagram and instruction list.
Hi expert.. Please do it correct and fast within 30 minutes. What do modern PLCs use to keep their real-time clocks and Static RAM alive, when without 24V DC feed?
Hello Sir.Good Evening. I have a question in my home work related Control System Lesson. The following below is my question.Please advise, Thank you so much. "Give a control mechanical system and show how to get a transfer function of the system"
Design the electrical ladder diagram and PLC ladder diagram for the PLC problem below. 1. Lamp 1 turns on when momentary push-button switch 1 (PB1) or momentary push-button switch 2 (PB2) is pressed. 2. Lamp 2 turns on when momentary push-button switch 2 (PB2) and momentary push-button switch 3 (PB3) are pressed. 3. When the momentary push-button stop switch is pressed, Lamp 1 and Lamp 2 turn off. Lamp 3 is on when both Lamp 1 and Lamp 2 are off.
Determine the input and output connections for an oven with automatic temperature regulation. Cite examples/instances to demonstrate whether it will be referred to as an open loop or closed loop control system.