Explain the manner in which pollution is caused by solid industrial waste, industrial effluents and industrial waste gases.

Q: What happens to a product with significant moisture when it is being dried?

A: Whenever any product(food) with a significant moisture is dried, the moisture in it gets evaporated…

Q: A solar dish with a concentration ratio of 100 means a. solar power is multiplied 100 times b. solar…

A: The definition of a concentration ratio of solar concentration is the ratio of solar radiation…

Q: Cite two reasons why interstitial diffusion is normally more rapid than vacancy diffusion.

A: Interstitial diffusion is a diffusion method in which small solutes particles occupy the…

Q: QUESTION 3 An engineer has identified epoxy, a thermoset as an effective candidate for a specific…

A:

Q: A chromatographer fed up with waiting 36 minutes to accomplish a separation requiring 8000 plates,…

A: A) PLATE HEIGHT will be major than on first conditions, on the off chance that you descrease the…

Q: Q2 In a particular foundry, an engine component made of alumimum is to be produced using sand…

A: Given: Discharge , Q = 1.2 m3/hr  =1.2/3600 m3/s           Radius of top portion of sprue, R1= 0.01m…

Q: Calculate the surface-to-volume ratio of a sphere of radius r. Then calculate the total drop surface…

A: Given   Surface area, A =  2.80337 cm3 Radius, r1 = 0.50 nm              r2 = 1 mm Find…

Q: Write a short notes on Sherwood number, 5 chmidt number and Peelet number for mass transfer and…

A: GIVEN DATA-  dimensionless number given related to mass transfer We have to explain it

Q: If Xf = 42000 ppm, Xb= 70000 ppm, and Md= 1 kg/s then the mass flow rate of the brine is

A: Given DataXf=42000 ppmXb=70000 ppmMd=1 kg/s

Q: What are the differences between evaporation and transpiration?

A:

Q: Which Additive Manufacturing materials and processes (according to the ISO/ASTM 52900 standard) is…

A: A wax pattern is used to create a disposable ceramic mould in investment casting. A wax model of…

Q: Explain the surface heat treatment and what is its application

A:

Q: Q2) A steel gear is needed to be improved by increasing the carbon content within an outer surface…

A:

Q: Draw the possible ways to improve the thin film deposition rate in thermal evaporation technique.…

A: A popular technique of physical vapor deposition is thermal evaporation (PVD). It's one of the…

Q: Identify the casting process in which the chamber is fully immersed in the liquid metal in a…

A: Die casting is a metal casting process in which the molten metal is forced into a mold cavity.

Q: explain the total formation volume factor, Bt.

A:

Q: How to verify the quality of unplasticized polyvinyl chloride and how to perform the dimensional…

A: Dimensional checks are performed to ensure the article's geometrical and dimensional regularity.…

Q: What are the benefits of using a chain in place of a rope? What are the concerns about dropping an…

A: The advantages of having chain drive over rope are given below. a) In Power transmission through…

Q: Compare the methods of vacuum thermal evaporation and vacuum sputtering in terms of technical…

A: The vacuum thermal evaporation deposition technique involves heating the substance to be deposited…

Q: (b) Upper and lower punch is a crucial component that determines the flowability during thixoforming…

A: Characteristics of punch in thixoforming process

Q: A sand mixture was screened through a standard 12 mesh screen. The mass fraction of the oversize…

A:

Q: ooling effect of evaporation in terms of latent heat of vaporization

A: by the law of calorimetry we know that , heat transferred from the hot body will be absorbed by the…

Q: Examine the importance of technological advances, changing customer needs and shortening product…

A: The basic purpose of adding a filter in the exhaust pipes of the vehicles is to reduce the number of…

Q: GIVE REASONS AND EXPLAIN WHY YOU HAVE CHOSEN THIS SUBSTANCE TO BE USED TO MANUFACTURE DRILL BITS…

A: Drill Bits

Q: What do you think is the main difference of humidification process using fine mist or steam from…

A: The humidification process is a process by which the water vapor content of gas can be increased.…

Q: 6. The part of gating system which regulates the rate of pouring of molten metal in the mold is…

A: 6) ingate 7) strength to whitstand high temperature 8) matrix

Q: Consider a collection of 10,000 particles with each particle capable of populating one of three…

A:

Q: The hydraulic conductivity of an aquifer is 0.005 cm/sec, the hydraulic gradient is 0.02, and the…

A: a- the specific discharge is  calculated as followq=-KdhdxK=hydraulic conductivity dhdx=hydraulic…

Q: An aluminum film was deposited at a rate of 1 μm/min in vacuum at 25 °C. It was found that the…

A: So, Al vapours and oxygen are in mole ratio 4:3. Given, Oxygen volume (V)=10-3m3   So, Number of…

Q: You are working as a quality control engineer in a glass manufacturing company. What…

A: Below are the characterization techniques:- 1.X-Ray fluorescence It tells the engineer how much…

Q: ANFO explosive is often preferred because using bulk explosives is cheaper, less labor intensive…

A: As explosive can be solid or liquid substances which is itself capable by chemical reaction…

Q: If the viscosity ofCl2 gaseous molecule at 20.0 °C and 1 atm. is 132 pP. what is the viscosity of dz…

A: Given data: The viscosity of 35Cl2 at the given temperature and pressure conditions is v1 = 132…

Q: Sintering is the process whereby green compacts are heated in a controlled atmosphere furnace to a…

A: In sintering process the green compacts are processed at a temperature below the melting point…

Q: What is the effective fiber diameter of a membrane filter with a pore size of 1 μm? The solidity is…

A:

Q: Illustrate both the adverse and therapeutic effects of factors presented in Fick’s law?

A: Fick's Law describes the relationship between the rate of diffusion. of gases into fluids. As per…

Q: according to this definition Alloys are metallic substances consisting of two or more metals, or of…

A: a) Composite materials also fit in this definition but are not alloys Reinforced concrete, Carbon…

Q: The slow sand filter at the Elletson Flats WWTP is not currently working. What pollutants are…

A:

Q: Which one of these may increase the amount of contact resistance? O Lower temperature during…

A:

Q: Difference between metallurgical efficiency and economic efficiency in relation to mineral processin

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.