Q A (10 K2) resistor is made of two strips connected in parallel, eachone has (40 um) thick, and (6 mm) long. One strip is of intrinsicgermanium and has (0.5 mm) wide. Determine the width of other strip ifit made of Ge., doped with (10²') donor atom/cm',at the workingtemperature. The intrinsic carrier density of Ge, is (2.5x10"m), andthe electron and hole mobilities are (0.4 m/V.Sec. , and 0.2 m/V.Sec.)respectively.0c

Given data: Two strips connected in parallel to form 10Ω resistor: Let, The length of 1st strip =…

Q A (10 K2) resistor is made of two strips connected in parallel, each one has (40 um) thick, and (6 mm) long. One strip is of intrinsic germanium and has (0.5 mm) wide. Determine the width of other strip if it made of Ge., doped with (1021) donor atom/cm',at the working temperature. The intrinsic carrier density of Ge, is (2.5x10"m), and the electron and hole mobilities are (0.4 m/V.Sec. , and 0.2 m/V.Sec.) respectively.

Q A (10 K2) resistor is made of two strips connected in parallel, each one has (40 um) thick, and (6 mm) long. One strip is of intrinsic germanium and has (0.5 mm) wide. Determine the width of other strip if it made of Ge., doped with (1021) donor atom/cm',at the working temperature. The intrinsic carrier density of Ge, is (2.5x10"m), and the electron and hole mobilities are (0.4 m/V.Sec. , and 0.2 m/V.Sec.) respectively.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

8. Each of the three insulators forming a string has a self capacitance of C farad The shunt capacitance of each insulator is 02C to earth and 0-1 C to line. A guard-ring increases the capacitance of line of the metal work of the lowest insulator to 0-3 C. Calculate the string efficiency of the arrangement: )with the guard ring. (7) without guard ring. 10 95% () 86 13%|
The intrinsic carrier density at 300 K is 1.5x 10¹0 /cm³, in silicon. For n-type silicon doped to 2.25 x 10¹5 atoms/cm. Find the equilibrium electron and hole densities.
The intrinsic carrier density at 300 K is 1.5 x 10¹0 /cm³ in silicon. For n-type silicon doped to 2.25 x 10¹5 atoms/cm. Find the equilibrium electron and hole densities.
2. There is a (p+)-n semiconductor for solar cell application. The p-n junctions are used to produce electrons and holes by adsorbing photons in the junction. Assume that the doping concentration NA on the p-side of this junction is the same as N, on the n-side. Each side is many diffusion lengths long. Find the expression for the hole current I, in the p-type material.
Subject - Semi Conductor's At 300K, fermi level is found to be 0.2eV below the edge of conduction band for an n-type silicon semiconductor. Find the electron and hole concentrations. After doping again, fermi level is now founded 0.25eV below the edge of conduction band. Find the type and concentration of impurity atoms added at the later stage At 300K, Nc= 2.8x 1019 cm3
8. Each of the three insulators forming a string has a self capacitance of C farad. The shunt capacitance of each insulator is 0-2 C to earth and 0-1 C to line. A guard-ring increases the capacitance of line of the metal work of the lowest insulator to 0-3 C. Calculate the string efficiency of the arrangement: (i) with the guard ring, (ii) without guard ring. [(i) 95% (ii) 86-13%)
Consider the two devices shaun below which are fabricated from the semiconductor material. same i) ii) p-type metal n-tmpe Metal metel n-pe metal than ncident on b) if the metal contects across the device is connected with a wire, do you expect current flow hE any ii). in device i) and Explain in te werds each.
Problem 2. In a typical MOSFET structure with a p-Si body, the Drain/Body and Source/Body regions are comprised of pn- junction diodes because the Drain and Source electrodes are attached to the p-Si body layer through a small island-like region of n-Si. If these n-Si regions were not present, describe what would happen if you tried to measure the channel current between the Source and Drain electrodes in this device (assuming the gate voltage has properly created an inversion channel)?
Which statement(s) is (are) true about a P-N junction: A. P-N junction consists of n-type and p-type semiconductor materials.B. Free electrons in n-type diffuse across junction to p-type.C. A depletion region formation happens due to electrons and holes moving away from each other due to the electric field.
Transistors are made by doping single crystal silicon with different types of impurities to generate n- and p-type regions. Phosphorus (P) and boron (B) are typical n-and p-type dopant species, respectively. Assume that a thermal treatment at 1100°C for 1 h is used to cause diffusion of the dopants. For each case (i.e. for P doping into Si and for B-doping into Si) calculate the constant surface concentrations for each dopant that would be needed to achieve a concentration of 10^18 dopant atoms/cm^3 at a depth of 0.1 microns from the surface in Si after the 1 hour treatment at 1100 C. The diffusion coefficients of P and B in single crystal silicon at 1100°C are 6.5 * 10^-13 cm^2/s and 6.1 * 10^-13 cm^2/s, respectively
8. Each of the three insulators forming a string has a self capacitance of C farad. The shunt capacitance of each insulator is 0-2 C to earth and 0-1 C to line. A guard-ring increases the capacitance of line of the metal work of the lowest insulator to 0-3 C. Calculate the string efficiency of the arrangement: (1) with the guard ring. (if) without guard ring. () 95% (i1) 86-13%]
A picce of p-type silicon with a cross section of I mm x 1 mm and length of 10 mm has i resistivity of 10 0-m at 27°C. Ohmic contacts are fabricated on the surfaces at either end of the longest dimensions of the bar and a DC voltage of 10V is applied, Assuming a hole mobility uh -0.03 m/V-s, calculate: The impurity concentration The velocity of the carriers through the bar The time taken for carriers to transverse across the bar The magnitude of the current in bar iv)