G3 Module 4 Test
.pdf
keyboard_arrow_up
School
George Brown College Canada *
*We aren’t endorsed by this school
Course
101
Subject
Mechanical Engineering
Date
Dec 6, 2023
Type
Pages
7
Uploaded by AhnafHossain on coursehero.com
Gas Technician III – Module 4 Test
**Do not mark the quesƟon sheet
**Mark your answers on the scantron card only
**Use only pencil on the scantron card
**Write your name, student number, and date on the scantron
card
Rob Moncrieff
rmoncrieff@georgebrown.ca
1.
A gas 2 technician is allowed to work on gas appliances with an input not exceeding:
a.
100,000 Btu
b.
200,000 Btu
c.
1,000,000 Btu
d.
400,000 Btu
2.
A gas 1 technician is allowed to work on gas appliances with an input not exceeding:
a.
1,000, 000 Btu
b.
400,000 Btu
c.
A gas 1 technician can work with any gas input
d.
100,000,000 Btu
3.
What is the maximum fine that can be given to an individual found guilty of an offence under the
Act?
a.
$10,000
b.
$50,000
c.
$100,000
d.
$1,000,000
4.
Which of the following organizaƟons is responsible for developing and publishing the B149:1 gas
code?
a.
TSSA
b.
NPS
c.
ULI
d.
NHL
e.
CSA
5.
A cerƟficate holder shall noƟfy TSSA within ____________ of a change in the holder’s address.
a.
1 week
b.
30 days
c.
90 days
d.
1 year
6.
A gas technician 1, 2, or 3 is responsible for components upstream of a gas meter.
a.
True
b.
False
7.
What is the Fuel Industry CerƟficates Ontario RegulaƟon Document number?
a.
FS-255-23
b.
211/01
c.
212/01
d.
215/01
e.
211/23
8.
A G1 applicant must have worked as a G2 Technician for at least ___ years.
a.
2
b.
1
c.
4
d.
5
9.
A G1 applicant must work 4,000 hours under the scope of a G2 CerƟficate, and ______ of those
hours must be on equipment greater than 400,000 Btu’s.
a.
2,000
b.
1,000
c.
4,000
d.
200
e.
500
10.
A packaged rooŌop unit located 7Ō from the roofs edge:
a.
is not in violaƟon of the B149:1 Gas Code
b.
is in violaƟon of the B149:1 Gas Code
c.
poses an immediate hazard and shall be red tagged
11.
When must the owner of a commercial building have a fixed/ships ladder installed gaining access
to rooŌop mounted equipment?
a.
A fixed ladder is not required
b.
Always
c.
When the roof deck is 26Ō up to 50Ō high
d.
When the roof deck is 13Ō up to 26Ō high
12.
The hours required by a G1 applicant must be _________ supervised by a G1 technician.
a.
directly
b.
indirectly
13.
A gas 3 technician must be directly supervised at all Ɵmes.
a.
True
Your preview ends here
Eager to read complete document? Join bartleby learn and gain access to the full version
- Access to all documents
- Unlimited textbook solutions
- 24/7 expert homework help
Related Questions
as an aerospace engineering student, where do you utilize flight simulators?
arrow_forward
Please show system sketches and related energy flows for all problems. Solve the following:
The utility providing the electricity to the boiler in problem 1.1 uses the same fuel as that used in problem 1.4 and has an efficiency of 0.35. The cost of the electric boiler is, $3,000 with a 15 year lifetime. The cost of the fuel based boiler system is $5000 and has a lifetime of 20 years. The fuel cost is $0.10/kg and the cost of electricity is $0.20/kWh. There is a tax charge of $0.50/kg of CO2 emission that is passed on to the user whether the utility based electrical system or gas fired system is used. The unit is used for 10 hours per day, 280 days per year. Which process would you recommend in terms of fuel consumption, exergy production, carbon dioxide emission and theroeconomic cost? There is no cost associated with the water input. Note the total amount of fuel consumed is directly related to the carbon dioxide emission from each process.
Show below are the problems described in…
arrow_forward
Subject - Evaluate the factors that inform the selection of a renewable energy system in relation to a specific installation
Question - Describe advances in renewable energy technology and how they meet the needs of a specific installation
arrow_forward
Project 2: In company that designs road cars and heavy trucks, it important to make the proper selection of the engines. Your part as a system energy engineer is to make a proper selection between an engine operates on Otto cycle/gasoline engine or Diesel cycle/diesel engine. Your head of department asked you to provide a detailed technical report that shows your selection for engine to be used with heavy truck vehicle. This is best achieved by performing the following tasks: Section.1:
1. Which engine does operate at lower ??? and has higher air-fuel mass ratio?
2. Which engine does burn fuel more completely?
3. Which engine has lower fuel cost?
4. Explain what compression ratio for Otto and Diesel cycles means
5. Explain what cut-off ratio for Diesel cycles means
6. Explain the limitations of SI engines in terms of their ability to operate at much higher compression ratios. What is this limitation called?
7. Provide general plot(s) for thermal efficiency, ? vs compression ratio, r…
arrow_forward
I know that my answer b. was correct. But for future references, how do I know for sure the Psig range in a question like this?
arrow_forward
INTERNAL COMBUSTION ENGINESplease write clearly
arrow_forward
Complete soln pls. Use the moody chart when the factor "f" is to be determined
arrow_forward
Thermodynamics Question:
Steam enters a steady-flow throttling valve at 2 kg/s, temperature 400°C, and pressure200 kPa. It leaves at temperature 100°C and pressure100 kPa. Heat is lost to surroundings at a rate of 100 kW. The surroundings are 25°C. Is this process feasible?
Use: https://irc.wisc.edu/properties/
arrow_forward
I need answers with clear hand writing or using Microsoft word . ASAP
informations of thermal system
arrow_forward
Module 4 Heating Effect of Electric CurrentHow long will it take to raise the temperature of 880 gm of water from 16ºC to boiling point ? The heater takes 2 amperes at 220 V and its efficiency is 90%.a.11.26 minc.13.08 min
b.12.56 mind.14.05 min
____ 13. An electric kettle is required to raise the temperature of 2 kg of water from 20ºC to 100ºC in 15 minutes. Calculate the resistance of the heating element if the kettle is to be used on a 240 volts supply. Assume the efficiency of the kettle to be 80%.a.72 ohmsc.83 ohms
b.62 ohmsd.93 ohms
arrow_forward
WILL SURELY GIVE AN UPVOTE IF ANSWEREDSUBJECT: THERMODYNAMICSINSTRUCTION: FOLLOW THE SET OF INSTRUCTIONS THAT IS LISTED IN THE IMAGE.
Will Not Violate The Academic Integrity/Honor Code Violation.
arrow_forward
State the purpose of the different sections that make up atypical automotive work environment.
arrow_forward
An auxiliary power unit (APU) is a relatively small, self-contained generator used in aircraft to start the jet engines, usually with compressed air, and to provide electricity, hydraulic pressure, and air conditioning while the aircraft is on the ground. It is known that 1 out of 200 tests performed in APU results in a failure. What is the probability that the failure occurs at the 20th flight test?.
Don't use chat gpt
arrow_forward
Need step by step solution
ASAP
arrow_forward
AMNT 280 Assignments 1-4 Media Presentation Categories Of Reciprocating Engines
Develop a Media Presentation
develop a power point media presentation Presentation will require researching a module specific topic
For this activity you will research the four categories of reciprocating engines In your presentation address the following:
1 Research the four different types of reciprocating engines2 Provide an overview of the design, construction, and firing order of each engine 3 Provide research concerning which air frame used the engine
Presentation Guidelines
Note:This information applies to all Media Presentation activities and will not be repeated Present your research material in the format of a written document (Introduction, body, and conclusion) Presentation requirements consist of 5-7 slides with a balance of both bullet text information and images; does not include the title or reference slide APA formatting and structural guidelines apply
Additional information…
arrow_forward
Please do both parts
Simple question
Asap
arrow_forward
Instruction: Show your solution. (Engineering Utilities 2) Problem: A compressor draws in 500 cubic feet per minute of air whose density is 0.079 pounds per cubic feet and discharges it with a density of 0.304 pounds per cubic feet. At the suction, pressure # 1 = 15 pounds per square inches and at the discharge, pressure # 2 = 80 pounds per square inches. The increase in internal energy is 33.8 Btu per pound of air, and the heat rejected from air by cooling is 13 Btu per pound of air. Determine the work done on the air in Btu per minute and in horsepower. (1Btu = 778.16 ft-lbf; 1hp = 42.4 Btu/min)
arrow_forward
please I want step by step answer to ge the solution ... ~~
arrow_forward
Subject: meca
arrow_forward
An electric motor drives a large air conditioner in a temperature controlled laboratory which handles all test samples for a major pharmaceutical company. There is no standby air conditioner, but there is a spare motor in the company’s stores. What classification would you assign to the air conditioner? Explain the reasoning behind your answer.
arrow_forward
1. Which statement heat describes the conversion of engine torque output into an understandable term of work. 01. Horarpower is derived fram torque and engine rpm. 02. Torque is derived from horsepower and engine rpm 03. Horsepower increases with increased engine rpm 04. Tarque will vary with engine speed.
arrow_forward
Case #1: A 10 -story office building has an electrical system with an automatic switch
of 200 amps on the main panel. On the 6th floor, an employee brings a high coffee machine
Power that makes the diliters constantly shoot. The building manager
worries about the impact that this could have in other tenants of the building and decides that
You need a solution. What is the best solution to solve this problem?
arrow_forward
Pls. Answer thank you!
The inside design conditions for a conditioned space are 20.1°C dry-bulb and 15.2°C wet-bulb. The air temperature increases 10.6°C as it passes through the conditioned space. The apparatus dew point is 11.9°C. The heat transfer rate is 456 Kw. What is most nearly the volumetric flow rate of the air passing through the space?
arrow_forward
SEE MORE QUESTIONS
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Related Questions
- as an aerospace engineering student, where do you utilize flight simulators?arrow_forwardPlease show system sketches and related energy flows for all problems. Solve the following: The utility providing the electricity to the boiler in problem 1.1 uses the same fuel as that used in problem 1.4 and has an efficiency of 0.35. The cost of the electric boiler is, $3,000 with a 15 year lifetime. The cost of the fuel based boiler system is $5000 and has a lifetime of 20 years. The fuel cost is $0.10/kg and the cost of electricity is $0.20/kWh. There is a tax charge of $0.50/kg of CO2 emission that is passed on to the user whether the utility based electrical system or gas fired system is used. The unit is used for 10 hours per day, 280 days per year. Which process would you recommend in terms of fuel consumption, exergy production, carbon dioxide emission and theroeconomic cost? There is no cost associated with the water input. Note the total amount of fuel consumed is directly related to the carbon dioxide emission from each process. Show below are the problems described in…arrow_forwardSubject - Evaluate the factors that inform the selection of a renewable energy system in relation to a specific installation Question - Describe advances in renewable energy technology and how they meet the needs of a specific installationarrow_forward
- Project 2: In company that designs road cars and heavy trucks, it important to make the proper selection of the engines. Your part as a system energy engineer is to make a proper selection between an engine operates on Otto cycle/gasoline engine or Diesel cycle/diesel engine. Your head of department asked you to provide a detailed technical report that shows your selection for engine to be used with heavy truck vehicle. This is best achieved by performing the following tasks: Section.1: 1. Which engine does operate at lower ??? and has higher air-fuel mass ratio? 2. Which engine does burn fuel more completely? 3. Which engine has lower fuel cost? 4. Explain what compression ratio for Otto and Diesel cycles means 5. Explain what cut-off ratio for Diesel cycles means 6. Explain the limitations of SI engines in terms of their ability to operate at much higher compression ratios. What is this limitation called? 7. Provide general plot(s) for thermal efficiency, ? vs compression ratio, r…arrow_forwardI know that my answer b. was correct. But for future references, how do I know for sure the Psig range in a question like this?arrow_forwardINTERNAL COMBUSTION ENGINESplease write clearlyarrow_forward
- Complete soln pls. Use the moody chart when the factor "f" is to be determinedarrow_forwardThermodynamics Question: Steam enters a steady-flow throttling valve at 2 kg/s, temperature 400°C, and pressure200 kPa. It leaves at temperature 100°C and pressure100 kPa. Heat is lost to surroundings at a rate of 100 kW. The surroundings are 25°C. Is this process feasible? Use: https://irc.wisc.edu/properties/arrow_forwardI need answers with clear hand writing or using Microsoft word . ASAP informations of thermal systemarrow_forward
- Module 4 Heating Effect of Electric CurrentHow long will it take to raise the temperature of 880 gm of water from 16ºC to boiling point ? The heater takes 2 amperes at 220 V and its efficiency is 90%.a.11.26 minc.13.08 min b.12.56 mind.14.05 min ____ 13. An electric kettle is required to raise the temperature of 2 kg of water from 20ºC to 100ºC in 15 minutes. Calculate the resistance of the heating element if the kettle is to be used on a 240 volts supply. Assume the efficiency of the kettle to be 80%.a.72 ohmsc.83 ohms b.62 ohmsd.93 ohmsarrow_forwardWILL SURELY GIVE AN UPVOTE IF ANSWEREDSUBJECT: THERMODYNAMICSINSTRUCTION: FOLLOW THE SET OF INSTRUCTIONS THAT IS LISTED IN THE IMAGE. Will Not Violate The Academic Integrity/Honor Code Violation.arrow_forwardState the purpose of the different sections that make up atypical automotive work environment.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning