MultiSim Assignment

Q4

1960048cmid 11667 This course For the below circuit, find the current i1 through the 18 ohms resistor. 40 120 V Select one: O a. in= -8A O b.iy=-4A O c.-4A O d.in-8A Find Rab- 20 ()

I need help understanding this question, what does this question is talking about

Create a circuit and apply kirchhoffs laws

Consider the RC circuit in Figure 2 below. Assuming the switch has been open for a long time before it is closed, fill in a table providing the current through each component and the voltage across each component immediately after the switch is closed, and a very long time after the switch is closed. Next, figure out the time constant for the circuit. (Hint: Assign currents to each branch. Set up the necessary KVL and KCL equations. Eliminate all but one variable to get an equation for just one of the currents. You shouldn’t have to solve this equation to recognize the time constant!)

PLS PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY. DRAW CIRCUIT DIAGRAM. PLS PLSS SHOWS HOW ALL THE EQUATIONS ARE REDUCED TO NEEDED.

A two element series circuit has voltage V = 240Z0°V and current I= 50Z-60°A. Determine the current which results when resistance value is reduced to 30%.

A lead wire and an iron wire are connected in parallel. Their respective specific resistances are in the ratio 49: 24. The former carries 80 percent more current than the latter and the latter is 47 percent longer than the former. Determine the ratio of their cross sectional areas ROUND OFF TO THE NEAREST HUNDRETHS

PLEASE ANSWER BOTH QUESTIONS FOR UPVOTES. NO UPVOTE IF ONLY ONE HAS AN ANSWER. PUT ONLY BRIEF EXPLANATIONS ON CHOOSING THE CORRECT ANSWERS. THANK YOU

Create a reverse bias graph using the figure below.

Shunt PMMC was designed by using indirect method to provide an ammeter with current range 5A, 10A, 20A. The internal resistance is 500 and full scale current of 1mA, find Rb.

What is the difference between the cut-off voltage VGS0 f and the narrowing voltage Vp? Explain this with the diagram

Subject to a step input, the voltage drop across the resistor took 696.3103us to reach 13% of its steady value from rest. Determine the time (ms) needed to reach 90% of its steady value from 10% Determine the time (ms) needed to reach 80% of its steady value from 20%

Subject: CircuitsGivenRt = 37.9529 ohm..Rcd = 3.6 ohm.Rab=2.3529ohmIt=1.58APt=94.85WV2=3.16VV4=6.32VVab=3.7175vVcd=5.688VI10=0.372AI5=0.7435AI8=0.465AI9=0.632AI6=0.348AP2=4.9928WP4=9.9856WPab=5.88WP14=34.95WPcd=8.99WP12=29.96W

BASIC ELECTRICAL ENGINEERING (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. BOX THE FINAL. ANSWER IT ASAP.)

BASIC ELECTRICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTONS LEGIBLY.

With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz

i've already seen this solution. but regardless, i askedfor an explanation. i always have a big issue with understanding how to do nodal analysis in these type of circuits, how to name nodes and on what basis. how was the outgoing current 0-v0/3r and how do i identify it and in the incoming current. how to use voltage division rule here. so please annotate everything on the figure and help me understand all my above inquiries so i can understand how to solve these type of questions. thank you! please be extremely detailed and concise. also when can i and can i not use nodal analysis and voltae division rule

The voltage across the resistor in series RL when suddenly supplied by a DC source is? a. zero O b. minimum O c. infinity O d. maximum

Solve this

Shown in the figure is an RL series circuit in which R= 10 ohms and L= 0.1 Henry. This is energized by a 24 volt DC source. If the switch is closed at t=o. Find voltage drops across Resistor R and inductor L when t=7.5 ms

in this circuit(voltage to current) what is the relation between the current and the voltage input and the resistors

solve all clear and correct or dislike

#4

9. The initial rate of current rise in an R-L circuit is 800 amps per sec when 453 volts is suddenly impressed. What is the inductance of the circuit?

Create five(5) Kirchhoff's Voltage Law (KVL) problem with figure and solve it(Show complete solution)

Please, can you solve the question as soon as possible.