TECH8015-Lab3_Helioscope20230103

1)an instrument that graphically displays measurements of Voltage value, frequency and phase difference in Electrical and electronic circuits on a digital or analog screen .......................’tour. 2)an instrument that measures the electrical power attracted by receivers in correct and alternating current circuits.....................’dir. What should come to the dotted line?

Explain the specific concepts and processes for the design methods that can effectively and efficiently design the electric and electrical systems (Ex. wireless power transfer systems, electric motors, solar power plants, etc.) in detail with some pictures and figures.  MAKE A PRESENTATION WITH EXAMPLES.

Discuss briefly the importance of renewable energy.

Discuss the importance of renewable energy.

Explain the specific concepts and processes for the design methods that can effectively and efficiently design the electric and electrical systems (Ex. wireless power transfer systems, electric motors, solar power plants, etc.) in detail with some pictures and figures.

= A Q.1): Assume that a decision is taken ordering all houses and establishments in a community to use kitchen grinders for food waste disposal to the waste water collections system , Discuss and evaluate the important mpacts on:.. .......................................................... Mgt ssesttsseseesanansstiasianevanunsssser( 20 IATKS) a. Solid wastes generation rate physical and chemical composition and characteristic. b. On -site handing and storage processes. &G c. Collection facilities = 3 d. Environmental and public health problems 23 e. On disposal by landfill , incineration or composting Sy 0D M)

please sir solve these 2 questions, thanks alot

Discuss the importance of voltage regulation in power systems.

With reference to energy conversion process, write the difference between Solar Power Tower system and Solar Photovoltaic System. Draw the structure of a solar cell and mark the electron flow direction and electric current flow directions

............................is required to stabilize an absolutely unstable system to achieve a specified performance.

1. What are the five basic ideal, electronic component models used to model all other electronic devices? 2. What is the formula for each of the five, ideal models that expresses the relationship between voltage across and current through the device? 3. What is the phase shift between the voltage and the current introduced by each of the five, ideal component models?

3. Fast help needed to answer this Engineeing question. Check image.   Postive feedback for right answer :)

Write the applications of Renewable Energy Systems  .

Construct a 3 paragraph introduction about Kirchoff's Laws. (Voltage and Current Law). Also, give possible reasons for some discrepancies between the actual values of voltage and current and the manual computation of values.

. Describe how each renewable energy system could be connected with local energy systems. . Discuss how renewable energy systems will bring benefit to the people living in the chosen area. . Summarise the efficiencies of a variety of combinations of renewable energy technologies for a chosen location.

Solve it fast plz

Give a brief introduction about the topic of generation and measurement of direct current voltage...(if possible for 2 pg or 1 pg) high voltage engineering subject..

Match the following Coal Kinetic Energy Wind Choose... Water stored in dam Choose... Uranium Choose...

answer number 2.write your solution pls.

A series circuit consisting of a 50 – ohm resistor, 0.5 – henry inductor, and a 100 – microfarad capacitor is connected to a 110 – volt, 50 cycle source. Calculate the following: a.) TOTAL IMPEDANCE b.) CURRENT c.) VOLTAGE DROP ACROSS THE RESISTOR d.) VOLTAGE DROP ACROSS THE INDUCTOR e.) VOLTAGE DROP ACROSS THE CAPACITOR f.) AVERAGE POWER g.) APPARENT POWER h.) REACTIVE POWER i.) POWER FACTOR j.) POWER FACTOR ANGLE DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES

Q5. Predictive maintenance is to be applied to an industrial conveying system. a) Discuss and illustrate the difference between reactive, preventative, and predictive maintenance. b) Describe several of the techniques that could be used to develop a predictive maintenance system for the conveyor system. Consider some of the sensing techniques that might be used and what parameters might be measured to detect component degradation. c) If the predictive maintenance system described in b) detects that the conveyor system is vibrating abnormally, discuss what condition this could indicate and what maintenance might be required.

Electrical Engineering An insulator has 3 units. The capacitance between each insulator pin and earth is 15% of self capacitance of each unit. Find: a. Voltage across each insulator unit in percentage. b. String efficiency.

Answer me in detail

3. Discuss the limitations in the application of Kirchhoff's laws to railway and other power systems. In what manner do these circuits differs from the usual battery circuits in which the emfs and resistances only are given?

What are the field of practice in electrical engineering? Give examples

A Printed Circuit Board (PCB) machine installs integrated circuits onto a board. Before starting to produce a board, the PCB machine requires a 25-minute setup. Once in production, the PCB machine requires only 0.16 minute per board. a. (Do not round intermediate calculations. Round your answer to 2 decimal places.) Currently, the PCB machine produces 600 boards between setups. Given this operating process, what is the capacity of the PCB machine (in boards per minute)? (Do not round intermediate calculations. Round your percentage answer to 2 decimal places.) Currently, the PCB machine produces 600 boards between setups. Given this operating process, what is the utilization of the PCB machine? b. Say the PCB machine produces 400 boards between setups and demand is 3 boards per c. minute. Given this operating process, what is the average inventory of boards at the PCB machine? (Round your final answer to 2 decimal places.) d. Demand for boards occurs at the rate of 3 boards per minute.…

Explain the relationships between PV cells, modules, panels, and arrays.