Physio Lab Report 3

I need the answer as soon as possible

Answer all the items. Thanks!

This multiple choice Questions from MEASUREMENTS INSTRUMENTATION course.

The answer in the following image are wrong, so provide your work in. a written format, if you provide in typed format or provide the same answers as shown in the image your answer will be downvoted. A patient takes 250 mg of a drug at the same time every day. Just before each tablet is taken, 5% of the drug remains in the body. (a) What quantity (in mg) of the drug is in the body after the third tablet? After the nth tablet? third tablet 263.125 ✓ mg nth tablet 263.157(1-0.05¹) X mg (b) What quantity (in mg) of the drug remains in the body in the long run? (Round your answer to three decimal places.) 263.157 X mg

Could you answer this?!

(01) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.

1. Caused by one or more cells not producing voltage. May be due to cheap construction, overheating or mechanical damage. A. Loss of active materials B. Internal Shorts C. Sulfation D. Internal Corrosion 2. Result of excessive depth of discharge and age. Mostly a problem with cheaper batleries. A. Loss of active materials B. Internal Shorts C. Sulfalion D. Internal Corrosion 3. The unit of measurement used for electrical pressure is- A. ohm B. volt C. energy D. amperes 4. What will happen if a Solar module is not properly oriented? A. Nothing B. Power is reduced due to different solar position during each season C. Power is increased due to different solar position during each season D. All of the above 5. In taking the Voc, you should set the multi-meter : A. High to compensate for the power B. Low to compensate for the current C. Volts DC D. 20 A DC

Please answer all subparts for like either dislike is ready.. Please all subparts in short..

Summarize on how testing is carried out on isolators and circuit breakers of high voltage system. High voltage engineering

Find the total resistance in Rbd

Electrical Machines 2 identify any equiptment at home that undergo an electromechanical energy conversion. name and discribe the function of each part involved in the conversion of the specific equiptment

Post Test Choose the letter of the correct answer. Write the chosen letter on a separate sheet of paper. 1. It is a smail component that lights up when current flows through it. a. Capacitor 2. It regulates the amount of current flowing in an electronic circuit. a. Capacitor 3. These are devices or components which do not require an external source to their operation. b. Fuse c. LED d. Resistor b IC c. Inductors d. Resistor c. passive devices d. electrical devices a. active devices b. electronic components 4. It is a three-terminal active component that is used mainly in boosting or amplifying electrical signals; both AF and RF ranges. a. Capacitor 5. it is necessary to turn the electrical circuit "on" or "off" a. Fuse 6. Testing tools that are capable of executing tests, reporting outcomes, and comparing results with earlier test runs a. Automated 7. The testing method that starts a soon as code is written and continues in successive stages as code is combined with other units of…

I Need the answer as fast as possible please

PMMC type meter has a full scale deflection of 10 mA. The resistance of the coil is 30 ohm So,   (1) Value of shunt for ammeter of 50 A range and   (2) Find the value of series resistance required for the range up to 500 V.

Note: Please do not handwritten.

Kindly check the answer mentioned in picture containing the question  before submitting the solution .

Why PMMC Voltmeters can not be used to measure higher voltages directly? a. because the size of the coils will raise b. because the coils will not be present at all c. because of the lesser current ratings. d. because of the lesser size problems

(02) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) What is the minimum value for RL needed to turn Zener diode ON?, And what is the maximum value for RL needed to turn Zener diode is ON? -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.

Solve it clearly please and I don't want it by hand writing

Q2/A- what are the main cases of insulator failures? B-what are type testing of insulator?

Can you help me set up my breadboard so I can ... Measure the values of base current, _________, collector current, _________ ?

Typing format..

Discussion Questions 1- Draw the important components of a steam power station. 2- What factors are taken into account to select the site of steam power station. 3- State the main parts of a thermal power station, and discuss the function of each part. 4- Draw the important components of a Hydro-Electric power station. 5- What factors are taken into account to select the site of Hydro-Electric power station. 6- Draw the important components of a nuclear power station. 7- What factors are taken into account to select the site of nuclear power station. 8- What do you understand from the load curve and what information are converged by a load curve. 9- Discuss the important points to be taken into consideration while selecting the size and number of units generation. 10- Explain the terms, connected load, load factor, plant use factor, diversity factor.

State and explain Paschen’s law. How do you account for the minimum voltage for breakdown under a given pd condition?

I need the answer as soon as possible

choose the correct answer In solar power plant, the cost of concentrating collector is more than flat platecollector.    TRUE or FALSE

Question 6 Feedback Vin Incorrect. + R1 Vb + Given a diode circuit with Vin = 1.5 V, R1 =1.8 kOhms, Vb 5.9 V. Determine the current along the diode. Consider the diode as ideal. ID=_____ MA Round your answer to 2 decimal places. Your Answer: -2.44 D1

Force Completion This test can be saved and resumed at any point until time has expired. The timer Remaining Time: 39 minutes, 41 seconds. v Question Completion Status: A Moving to another question will save this response. Question 1 In semiconductors, the valance electrons need some energy to move to the conduction band. True False A Moving to another question will save this response.