EET230_Lab5_Taylor_Jason

(a) ii please in photo

VI Ru Ri Vz I, Io R2 = 3837.79 O. R3 = 3989.3 Q. %3D R4 = 2898.06 Q. V1 = 4.8 V. V2 = 8.1 V. 11 = 0.0099 A Determine the following: a.) The output current lo %3D

In an R-2R type DAC circuit taken as logic 1 = 3 volts and logic () = 0 volts, if the output voltage is measured as l Vo l = 3.75 volts, design it by calculating the input logic value.

Solution all part

what is the difference between a sequential circuit and a combinational circuit in Digital Circuit engineering?

The data-input and data-select waveforms in Figure 7 are applied to the multiplexer. Determine the output waveform F in relation to the inputs.

Explain the process of converting Analgoue to digital converter? Compare the difference in process and 10 applications where we can use ADC and DAC. Also draw the circuit and flow diagram any one type of ADC by hand

I need the answer as soon as possible

a)circuit diagram with a load ,for the JFET. b)input and output waveform c)equations for the output ( v and i)

3c. Please I want a solution of this question with all details. Many Thanks Note: It is preferable to solve by typing.

I need the answer as soon as possible

This is an Electronic subject. Please provide a step-by-step working solution. Thank you.

Digital Electronics and Design Questiona) Write a 2:1 MUX module using Verilog-HDL.b) Use the module in (a) and write a Verilog-HDL code to implement a 4:1 MUX.

Explain the concept of Ohm's Law and its relevance in analog electronics. Demonstrate an example and show how it works in amplifier network analysis in the DC or AC domain

electronics engineering What are IC Voltage regulators? State the different IC voltage regulators and its operation.

3. Graphical Representation of the signal 1) Write the type of the voltage from simulation results: 2) Write the value of the voltage from simulation result: L....... -2 DDU 12ns SónG Trace Color Trace Name X Values CURSOR 1,2 V(R1:1,0) Y1 Y2 Y1 - Y2 5.0373m 0.000 5.0373m 249.983 0.000 249.983 Y1(Cursor1) - Y2(Cursor2) Y1-Y1(Cursor1) Y2 - Y2(Cursor2) Max Y Min Y Avg Y 249.983 0.000 0.000 249.983 0.000 124.991

NOTE: THIS IS A ELECTRONICS ENGINEERING SUBJECT

requirements 4 and 5

answer fastly please 57. Discuss the concept of metastability in digital circuits.

Suppose there is a system consisting of temperature sensor, ADC, DAC and a Fan. The   temperature sensor gives output as voltage value. As the temperature increases more than 18°C it produces the voltage of 8.17 V. That voltage is then put through a 4-bit Successive Approximation ADC as input. After that the output of that ADC is applied to a 4-bit R/2R- ladder DAC to produce enough voltage to turn ON the fan. Take R=”Group#” KΩ. Consider logic “1” as 7 V and logic “0” as 2V. (i) Illustrate the block diagram for the system showing ADC, DAC, Fan and temperature sensor. (ii) Design the circuit diagram with ADC & DAC for the complete system showing necessary parameters value.

i need the answer quickly

Produce a working circuit with the Integrated Circuits shown in the image.

Discuss the significance of analog-to-digital converters (ADCs) in microcontroller applications. Explain how ADCs work and provide examples of applications that heavily rely on ADCs.

Digital Electronics and Design Question Consider the CMOS implementation given in the figure. Find out the implemented function.

answer fast

Please solve the problem. Answer all subdivisions please

Number 22

Only d) deatils rae important so laeve/ jump nothing unexplained

Draw a diagram showing the interface between an 8-bit Analog to Digital (A/D) converter and 8051 microcontroller. Write the necessary assembly instructions to start the A/D conversion, wait for it to complete, and read the digital data after the conversion.

1. For the pointer position in the diagram, what is the input signal if the range is set at 0.3 V? A. For the pointer position in the diagram, what is the input signal if the range is set at 1 V? B. For the pointer position in the diagram, what is the input signal if the range is set at 30 V? C. Let’s say you know that the input signal will be about -0.25 V. What range should you select to give maximum deflection without going off scale? Draw a line, with a straight-edge, on the picture above, showing how the pointer would point.