driving

A vehicle's Maximum Gross Weight (MGW) can be found on the New York State registration and is used to determine what type of safety inspection is done on a vehicle. True or False?

Select whether the following statement's are true or false: Structural safety is solely the responsibility of the aircraft manufacturer and the airworthiness authorities. If a structural component is not inspectable, it can still be certified according to one of the available design philosophies. Decreasing the stress amplitude while maintaining the mean stress means that less work or energy is applied to the structure, and thus less damage is caused resulting in a longer fatigue life.

Non- Destructive Testing Critical thinking essay as being professional engineer answer 2. Rank all kinds of NDT from the most expensive to the cheapest. 3. What is the most used NDT process in the industry? Check the guide below

Provide an overview of the fundamental components that make up an application that is capable of satisfying the criteria for car safety inspections.

Answer the following question: 1. What are the the things that needs to be checked when performing an on-aircraft inspection?

The following is a series of questions pertaining to the NSPE Code of Ethics. Please indicate whether the statements are true or false. These questions are provided by the NSPE. Note: This ethics test is intended solely to test individual knowledge of the specific language contained in the NSPE Code of Ethics and is not intended to measure individual knowledge of engineering ethics or the ethics of individual engineers or engineering students. Engineers shall acknowledge their errors after consulting with theiremployer or client.

Non destructive testing 1. Give your analysis on how NDT can be use in the current industry. 2. Rank all kinds of NDT from the most expensive to the cheapest. 3. What is the most used NDT process in the industry? check the image below for guide.

Answer the following question: 1. When to conduct a special inspection on the aircraft?

An accident investigation report must include all of the following except: The date of the accident Names of those witnessing the accident A description of the incident Factors that contributed to the incident

The following is a series of questions pertaining to the NSPE Code of Ethics. Please indicate whether the statements are true or false. These questions are provided by the NSPE. Note: This ethics test is intended solely to test individual knowledge of the specific language contained in the NSPE Code of Ethics and is not intended to measure individual knowledge of engineering ethics or the ethics of individual engineers or engineering students. Engineers shall not accept compensation, financial or otherwise,from more than one party for services on the same project, or for servicespertaining to the same project, unless the circumstances are fully disclosed

2) Explain The Principle Of Working And Operation Of Radiographic Inspection Technique Inspection With Neat Diagram.

QUESTION FIVE Kindly answer correctly. Please sho all the necessary steps

Which one of the below statements is mostly NOT correct about in creation of detailed design of component? The selection of material is based on what is required to performance the function. The tolerance is determined by the function, not the preference of designer or manufacture. In the selection of manufacturing processes, the number of components to be manufactured needs to be considered, as the capital investment needs to be considered. I do not need to show or prove the component is working: such how much electricity is generated in power panel, how much braking force is generated in by the brake disc, or how much the force the component in suspension is subjected?

What are the types of accident in industrial safety?  Examine some of the common source of mechanical hazards.  Organize the classification of pressure vessels.  Describe fault tree analysis.  What is the corrosion and its prevention?  What are the different types of wear and causes?  Enlist the points to be considered for safety in industries as per The Factories Act, 1948. What is lubrication and method of lubrication?   What is the concept and importance of fault tracing?  How do you draw a decision tree diagram?  What is periodic maintenance?  What are the steps in making preventive maintenance procedure?

Describe the framework of an application that would be capable of satisfying the criteria for automotive safety inspections.

submit at least 10 hazard symbols and its description used in a workplace. identify the workplace where that symbol is being used.

Design a complete and safe experiment to find out how increasing the distance of air that alpha particles must pass through affects their detection by a Geiger Muller tube. G-M In your plan you must include: A hypothesis that can be tested Am-041 . An identification of the independent, dependent, and two control variables A list of any additional equipment needed A justification of why additional equipment is needed A description of your method, How you will collect sufficient data A relevant safety consideration

Please answer correctly

The following is a series of questions pertaining to the NSPE Code of Ethics. Please indicate whether the statements are true or false. These questions are provided by the NSPE. Note: This ethics test is intended solely to test individual knowledge of the specific language contained in the NSPE Code of Ethics and is not intended to measure individual knowledge of engineering ethics or the ethics of individual engineers or engineering students. Engineers may issue subjective and partial statements if such statements are in writing and consistent with the best interests of their employer, client or the public.

Subject: Air Pollution Formation and Control Do not just copy and paster other online answers

A person is required to perform a lifting task. After conducting the analysis of the task shown below using the NIOSH lifting guidelines you determined that the task need to be redesigned to be acceptable. Unfortunately, the only factor that you can modify is the frequency of lifts per minute. What is the maximum number of lifts per minute that need to be used for this task so the NIOSH lifting guidelines are not exceeded?   ANSWER:  ________________

A non-destructive test is any examination of an object in any manner which will not impair the future usefulness of the object.  Non-destructive test include magnetic particle, impacting testing, radiography, eddy current, and fluorescent penetrant. True or false?

Although the information from different publishers vary in presentation and the arrangement of _______________, all are easy to use after you become familiar with their organization. Most are divided into a number of _______________, each covering different aspects of the _______________. The beginning sections commonly provide vehicle identification and basic maintenance information. The remaining sections deal with each different vehicle _______________ in detail, including diagnostic, _______________, and overhaul procedures. Each section has an index indicating more specific areas of information. To obtain the correct system _______________ and other information, you must first identify the exact system you are working on. The best source for vehicle identification is the _______________. The available information may also help you identify the system through the identification of key _______________ or other identification numbers and/or markings.

How important is the selection of an appropriate Factor of Safety for various applications and why it is one of the most important engineering tasks?

is a measure of internal resistance caused by electrical environment of the particles. a. Effective viscosity b. Apparent viscosity c. Plastic viscosity d. Yield point e. Both a and b

What are the type of aircraft propeller shop inspection? Define each

Which tool helps to categorise risks into three colour-coded zones representing major, moderate, and minor risks Risk Priority Number Risk assessment matrix Failure Mode and Effects Analysis O Severity Matrix