Acid And Base Titration Essay

4. To utilize the titration results to calculate the molarity of the hydrochloric acid and the

The results showed the molarity of the NaOH solution. This experiment was completed twice and a new average molarity

weak bases). After ranking the pH of these solutions, you will then test your predictions in the laboratory.

To start out this study the difference between acids and bases has to be identified. Acids have very low pHs and have a high concentration of hydronium ions, while bases have a high pH and have a high concentration of hydroxide ions. The difference between strong bases and acids, and weak bases and acids is the amount of dissociation. Strong bases and acids dissociate a large amount and let go of their ions in solution, while weak bases and acids may only let go of some of their ions. This is important because if the unknown solutions aren’t strong acids or bases then using their ions to calculate the pH of the solutions will give false results (Diffen 2012).

Three grams of a mixture containing Benzoic Acid and Naphthalene was obtained and placed in 100 ml beaker and added 30 ml of ethyl acetate for dissolving the mixture. A small amount (1-2 drops) of this mixture was separated into a test tube. This test tube was covered and labelled as “M” (mixture). This was set to the side and used the following week for the second part of lab. The content in the beaker was then transferred into separatory funnel. 10 ml of 1 M NaOH added to the content and placed the stopper in the funnel. In the hood separatory funnel was gently shaken for approximately one minute and vent the air out for five seconds. We repeated the same process in the same manner one more time by adding 10ml of 1M NaOH.

The purpose of this experiment was to determine the pKa, Ka, and molar mass of an unknown acid (#14). The pKa was found to be 3.88, the Ka was found to be 1.318 x 10 -4, and the molar mass was found to be 171.9 g/mol.

from the results. Here is an example of a conclusion for the acetic acid experiment used in

There might have been more KOH solution added to the flask resulting in the observations to be wrong.

Table 2: Consists of color extract taken from a red cabbage for a natural indicator. The pH reading that was measured by using the pH meter and the result of the pH reading to determine whether the solution was acidic or basic.

Chemistry 102 is the study of kinetics – equilibrium constant. When it comes to the study of acid-base, equilibrium constant plays an important role that tells how much of the H+ ion will be released into the solution. In this lab, the method of titrimetry was performed to determine the equivalent mass and dissociation constant of an unknown weak monoprotic acid. For a monoprotic acid, it is known that pH = pKa + log (Base/Acid). When a solution has the same amount of conjugate base and bronsted lowry acid, log (Base/Acid) = 0 and pH = pKa. By recording the pH value throughout the titration process and determining the pH at half- equivalence point, the value of Ka can be easily calculated. In this experiment, the standardized NaOH solution has a concentration of 0.09834 M. The satisfactory sample size of known B was 0.2117 g. The average equivalent mass of the unknown sample was found to be 85.01 g, pKa was found to be 4.69, which was also its pH at half-equivalence point and Ka was found to be 2.0439×〖10〗^(-5). The error was 1.255% for equivalent mass and 0.11% for Ka. In other word, the experiment was very precise and accurate; the identity of the unknown sample was determined to be trans-crotonic by the method of titrimetry.

ii. The second part of the titration series involves titration of NaOH with Hydrochloric acid (HCL). Again, three reps of titration and a blank titration have to be completed. A volumetric pipet is used to measure 10.00mL of HCL into three labeled conical flasks. Then the flasks are filled with deionized water until about the 50mL mark. A buret is

Within an acid-base titration the titration curve resembles the strengths of the corresponding acids and bases. A strong acid will correspond with a weak conjugate base, and a weak conjugate acid will correspond with a strong base. This is based on the Bronsted-Lowry model. The weak acid will donate protons to the hydroxide ion. Weak acids will have a low Ka value, the Ka value is the tendency of the acid to dissociate:

By using acid-base titration, we determined the suitability of phenolphthalein and methyl red as acid base indicators. We found that the equivalence point of the titration of hydrochloric acid with sodium hydroxide was not within the ph range of phenolphthalein's color range. The titration of acetic acid with sodium hydroxide resulted in an equivalence point out of the range of methyl red. And the titration of ammonia with hydrochloric acid had an equivalence point that was also out of the range of phenolphthalein.. The methyl red indicator and the phenolphthalein indicator were unsuitable because their pH ranges for their color changes did not cover the equivalence points of the trials in which they were used. However, the

First, three titration curves and three second derivative curves were created to determine the average pH at the half-equivalence point from the acetic acid titrations. Titration curves were used as visuals to portray buffer capacity. The graphs and a table, Table 1, that showcased the values collected were created and included below. The flat region, the middle part, of Figures 1, 2 and 3, showed the zone at which the addition of a base or acid did not cause changes in pH. Once surpassed, the pH increased rapidly when a small amount of base, NaOH, was added to the buffer solution. Using the figures below and

An acid-base titration is the determination of the concentration of an acid or base by exactly neutralizing the acid/base with an acid or base of known concentration. This allows for quantitative analysis of the concentration of an unknown acid