Advantage And Disadvantage Of Inverter

ABSTRACT- D.C. motors are seldom used in ordinary applications because all electric supply companies furnish alternating current. However, for special applications such as in steel mills, mines and electric trains, it is advantageous to convert low value of DC into high value of DC in order to use D.C. motors controlled by power electronic apparatus. Here the DC motor is controlled power electronic converters through RES system. Although the design of these converters has been presented at the operational level, some fundamental issues such as topologies, analyses, and control have not been thoroughly studied. In this paper, the basic HB TL topology is first presented. This is followed by the derivation of a systematic method of generating TL converter topologies, leading to the derivation of a family of TL converters with improvement and simplification for better functionality and practicality. This paper discusses wide range soft switching solutions to a pulse width

The impact of the proposed sequences has been simulated for 0.4 modulation index with a 0.5 lagging power factor load (power factor angle 60°). The simulation setup consists of the following software: 1) MATLAB/Simulink – used to implement the modulation strategies and switching sequences, and 2) PSIM – used to simulate the T-NPC inverter running with an R-L load and to provide conduction and switching losses of each switch. The inverter switching pulses were generated within Simulink and were fed to PSIM through sim-coupler module which provides a link between PSIM and simulink for the purpose of co-simulation [29].

The innovative inverter technology produces safe, smooth power, protecting your sensitive electronics (computers, smartphones, etc.) from damage.

III EEE, III EEE, III EEE , III EEE Lendi institute of engineering& Lendi institute of engineering& Lendi institute of Lendi institute of

Abstract— this paper presents a brief overview of standards for power electronics. All the standards presented in this paper are currently active and are approved by the Institute of Electrical and Electronics Engineer Standards Association (IEEE-SA) and American National Standards Institute (ANSI).

For reverse voltage blocking a diode is used in series with the self-commutating device (IGBT) . However, GTO-based configurations have restricted frequency of switching they do not need the series diode. They are considered sufficiently reliable, but have higher losses and require higher values of parallel ac power capacitors. Moreover, they cannot be used in multilevel or multistep versions to improve performance in higher ratings.

Abstract—This paper covers the need and use of power electronics in the application of renewable energy utilization. Covered in this paper is wind energy with variable speed drives and their controlling power electronics. Solar energy, specifically photovoltaics and their controlling power electronics. High-voltage direct current transmission lines and the power electronics that allow for this technology to exist.

For the last 25 years there has been a great increase in the usage of the solid state electronics technology. This new technology has provided us with the opportunity to have a product with a high quality with an increased productivity due to its high efficiency. Today, we can produce products with high quality at less cost than in the last years, but this new technology has given rise to a new problem, which is the need for a clear electric power.

As the reference voltage vector is formed using discrete switching vectors, the operating voltage vector does not follow the reference trajectory []. The deviations between applied switching vector and reference voltage vector results in the ripple in the output current waveform. For any switching instance, the instanteneous current ripple due to application of ith switching vector (i.e. application corresponding voltage vector Vi) can be written as

In general, solar PV module voltage is low, ranging from 30-60V DC. To meet the demand of AC loads, there is a need for inversion as well as a voltage boosting, whereas voltage boosting is dependent on parameters like module voltage, the number of modules, and their connection [7-9]. Thus, it is clear that PCS must have following functionalities, such as voltage boosting (optional), MPPT Tracking and inversion. The voltage boosting stage can be provided by either step-up dc-dc converter or transformer followed by an inverter [10-13]. But placing the transformer to raise the voltage level is not a good solution as it increases the cost, size, and volume of the overall system. Moreover, it lowers the efficiency of the system. Hence transformerless topologies received lot of attention in past few years [9]. Two types of transformerless solutions are suggested in the literature for solar PV power generations, namely a) multi-stage power conversion and b) single stage power conversion [23-24]. Whether it is single stage or multiple stage power conversion the most critical part of a solar PV system is the inverter, which will be discussed in next sections. At present, inverters are the essential cause of breakdown of huge scale PV systems [12]. Moreover, in addition to the quality problems, inverters give restricted power efficiency [7]. Normally, inverter efficiency is around 94% and as the load diminishes the efficiency can

This paper investigates adjustable speed induction motor drive using 2-level and 3-level PWM.The result obtained is verified using Matlab simulation.This result compares the hamonic contect in between 2-level and 3-level by FFT analysis tool.To analyse the resulta a carrier based pwm was taken using 2- level and 3- level topology and a threephase bridge convetor with internally generated capability SPWM/SVPWM was intrduced. Carrier freqency18*60Hz, modulation index 0.9, output voltage freqency 60 Hz and ouput voltage phase 0 degre Was fixed. So corresponing to above values,the motor speed was 1800 rpm. Or 188.5 radian/sec, hence torque is 11.87Nm. A two pole squirrel cage motor was taken subjected to 400V dc source with modulation index0.9 prduces 220v rms.when motor starts, at 0.5s it reaches its steady speed 181 radian/sec or 1728 rpm. Now by discretizing the FFT tool displays the frequency spectrum of voltage and current waveforms. These signals are stored in workspace in the ASM structure with time variable generated by the Scope block. As my model is discretized, the signal saved in this structure is sampled at a fixed step and consequently satisfies the FFT tool requirements.It was observed that value of total harmonic distortion(THD) was 65.77 percent in 2-level and 35.11 percent in 3- level for SPWM invertor and 56.77 percent for SVPWM invertor.

Abstract—This paper presents a systematic method for deriving three-port converters from the full-bridge converter by splitting two switching legs of full bridge converter into two cells with different sources. The Full bridge TPC can be used across a wide source voltage range, and good control over two of the three ports can be achieved while the third port provides the power balance in the system. Moreover, the energy stored in the leakage inductance of the transformer can be utilized to achieve zero-voltage switching for all the primary-side switches. Experimental results verify the feasibility and effectiveness of the developed Full Bridge-TPC.

This thesis deals with the configuration and investigation of control framework structures for electric drives furnished with changeless magnet synchronous machines (PMSM) in car application. With the expanding prominence of multi-level inverters, the opportunity to get better of the execution of voltage source inverters has persistently been tried for different applications. The fast improvement of high exchanging recurrence power gadgets in the previous decade leads towards more extensive use of voltage source inverters in AC power era. In this way, this prompts the requirement for a regulation method with less aggregate symphonious bending, less exchanging misfortunes, and more extensive direct balance range. The present theory highlights the examination of the customary two-level inverter and the three-level diode cinched inverters for the application in car industry.

This project is aim to study the principle of pwm, single-phase inverter, three-phase inverter which leading to design a three-phase inverter(DC-AC) by using the mbed to control switch. This inverter will be intended to drive an induction motor which may need to drive. The work will involve simulation study of PWM generators, induction motors and device selected from.

The conventional two levels Inverter have many limitations for high voltage and high power application. Multilevel inverter becomes very popular for high voltage and high power application. The multilevel inverter is started with the three level converters. The elementary concept of a multilevel converter to achieve higher power to use a series of power semiconductor switches with several lower voltage dc source to perform the power conversion by synthesizing a staircase voltage waveform. However, the output voltage is smoother with a three level converter, in which the output voltage has three possible values. This results in smaller harmonics, but on the other hand it has more components and is more complex to control. In this paper, study of different three level inverter topologies and SPWM technique is explain and SPWM technique has been applied to formulate the switching pattern for three level and five level H-Bridge inverter that minimize the harmonic distortion at the inverter output. This paper deals with comparison of simulation results of three levels and five