Advantages And Disadvantages Of Co-Precipitation

The objective of this experiment is to separate a 50:50 mixture of benzoic acid and benzil by using macroscale extraction. In the experiment, organic solvent diethyl ether is used. After adding 1.0 gram of the 50:50 mixture of benzoic acid and benzil to a 25ml Erlenmeyer flask, diethyl ether was added to the flask to dissolve the mixture. Benzoic acid and benzil dissolve in diethyl ether. Once the mixture dissolved in

Experiment 55 consists of devising a separation and purification scheme for a three component mixture. The overall objective is to isolate in pure form two of the three compounds. This was done using extraction, solubility, crystallization and vacuum filtration. The experiment was carried out two times, both of which were successful.

In the first acid extraction of benzocaine, the compound was dissolved in the organic solvent of dichloromethane. When the mixture was shaken with HCl, benzocaine’s amine group gained a proton and became more soluble in water than dichloromethane. This allowed the newly formed hydrochloric salt to migrate to the aqueous layer. However, the addition of NaOH to the acidic aqueous layer regenerated benzocaine by deprotonation, making it insoluble in the aqueous layer. The precipitation of an ionic salt was therefore recovered by vacuum filtration and had a tested melting point range of 85.1C-87.4C compared to 88C-90C, the literature melting point of benzocaine. The similarity in melting point ranges, but low percent yield of 30.37% proves that the extract was somewhat successful. Lower yields may be the result of spillage performed in the lab. In the second basic extraction, the organic layer now included benzoic acid and benzamide. When treated with NaOH to deprotonate benzoic acid, the newly formed sodium benzoate transitioned to the aqueous layer as a sodium salt. Benzoic acid is regenerated once again after the addition of HCl and became insoluble in the aqueous layer after protonation. Its precipitation was then filtered out for a 65.87% recovery. Compared to its literature melting point of 122.41C, the resulting 120.9C-123.5C melting range of the sample also supports the accuracy of the separation due to its similarities and high percent yield. In conclusion, the usage of base and acid liquid extraction was mostly successful in this experiment because it was able to efficiently and properly isolate the impure mixture into two separate components of benzocaine and benzoic acid. By performing the techniques of extraction and vacuum filtration, the similarities between literature and tested

There are millions of different organic compounds. Most of them are found in mixtures and in order to achieve a pure form they need to be separated, isolated, and purified. However, there are endless numbers of possible mixtures, which make it impossible to have a pre-designed procedure for every mixture. So chemists often have to make their own procedures. The purpose of this experiment was to prepare the student to the real world by them designing their own procedure which will help them understand the techniques of separation and purification better. The goal was to extract two of the components of the

Abstract: One mixture of two unknown liquid compounds and one mixture of two unknown solid compounds were separated, isolated, purified, and characterized by boiling point. Two liquid unknowns were separated, isolated, and purified via simple distillation. Then, the process of an acid-base extraction and washing were used to separate two unknown compounds into two crude compounds: an organic acid and a neutral organic compound. Each crude compound was purified by recrystallization, resulting in a carboxylic acid (RCO2H) and a pure organic compound (RZ). The resulting mass of the pure carboxylic acid was 1.688g with a percent recovery of 31.80%, the boiling range was 244-245 °C, and its density was 2.0879g/mL. The resulting mass of the pure organic solid was 2.4902g with a percent recovery of 46.91%, the boiling range was 52.0-53.4°C, and its density was 1.5956 g/mL.

The objective of this extraction experiment was to achieve a comprehensive understanding, as well as master the practice, of the technique of separating various individual components of a compound.

Chemically active extraction is a highly useful method of separating organic compounds in mixtures (Padias 128-37). Organic acids and bases are soluble in organic solvents, but their corresponding salts are soluble in water. Therefore, if one had a mixture of an acidic organic compound and a basic organic compound in an organic solvent, addition of a base

Solutions of 6M H2SO4, 6M NH3, 6M HCl, 6M NaOH, and 1.0 M of NaCl, 1M Fe(NO3)3, 1M NiSO4, 1M AgNO3, 1M KSCN, 1M Ba(NO3)2, and 1M Cu(NO3)2 were given in separate test tubes. The color of possible precipitates, ions, acid-base behaviour, odor and solubility rules were conducted and were reported in Table 1. The key information about a mixture of two solutions was

Objective: The objective of this experiment is to use acid-base extraction techniques to separate a mixture of organic compounds based on acidity and/or basicity. After the three compounds are separated we will recover them into their salt forms and then purify them by recrystallization and identify them by their melting points.

Experiment 4A: Determination of a Partition Coefficient for Benzoic Acid in Methylene Chloride and Water, and Experiment 4B: Solvent Extraction I: Acid-Base Extraction Using the System Benzoic Acid, Methylene Chloride, and Sodium Bicarbonate Solution

The main objective of this experiment is to carry out qualitative analysis to identify metal cations in unknown solution 1.

The purpose of this experiment was to use solvent extraction techniques in order to separate a mixture consisting of a carboxylic acid (p-toulic acid), a phenol (p-tert-butylphenol), and a neutral compound (acetanilide). Extraction is the process of selectively dissolving one or more of the compounds of a mixture into an appropriate solvent, the solution that contains these dissolved compounds is called an extract (Manion, 2004).

     Conventional Liquid Chromatography is most commonly used in preparative scale work to purify and isolate some components of a mixture. It’s also used in ultra trace separations where small disposable columns are used once and then discarded. Analytical separations of solutions for detection or quantification typically use more sophisticated high-pressure liquid chromatography instruments.

The cations in both the known and unknown samples were identified by using qualitative analysis, of which were determined to be acidic, basic, or neutral by using litmus paper. Acid-base reactions, oxidation-reduction reactions, and the formation of complex ions are often used in a systematic way for either separating ions or for determining the presence of specific ions. When white precipitate formed after adding hydroxide, aluminum ion was determined to be present in the solution. However, nickel was determined to test positive when the solution changed to a hot pink color after adding a few drops of dimethylglyoxime reagent and iron was present when the solution was a reddish brown color when sodium hydroxide was added to the mixture at the very beginning of the experiment. Qualitative analysis determines that ions will undergo specific chemical reactions with certain reagents to yield observable products to detect the presence of specific ions in an aqueous solution where precipitation reactions play a major role. The qualitative analysis of ions in a mixture must add reagents that exploit the more general properties of ions to separate major groups of ions, separate major groups into subgroups with reactions that will distinguish less general properties, and add reagents that will specifically confirm the presence of individual

1. Obtain a sample of the mixture. The mixture you will separate contains three components: NaCl, NH4Cl, and SiO2. Their separation will be accomplished by heating the mixture to sub-lime the NH4Cl, extracting the NaCl with water, and drying the remaining SiO2.