An Experiment On Extraction And Its Effect On Solubility And The Rule Of The Solvents

There are various techniques to separate a mixture of compounds from each other. One of the commonly used way to isolate compounds from a mixture of two compounds is called extraction. This method of extracting two compounds from each other relies on the different solubility of the compounds in two different solvents.

Experiment 55 consists of devising a separation and purification scheme for a three component mixture. The overall objective is to isolate in pure form two of the three compounds. This was done using extraction, solubility, crystallization and vacuum filtration. The experiment was carried out two times, both of which were successful.

14 mL of 9 M H2SO4 was added to the separatory funnel and the mixture was shaken. The layers were given a small amount of time to separate. The remaining n-butyl alcohol was extracted by the H2SO4 solution therefore, there was only one organic top layer. The lower aqueous layer was drained and discarded. 14 mL of H2O was added to the separatory funnel. A stopper was placed on the separatory funnel and it was shaken while being vented occasionally. The layers separated and the lower layer which contained the n-butyl bromide was drained into a smaller beaker. The aqueous layer was then discarded after ensuring that the correct layer had been saved by completing the "water drop test" (adding a drop of water to the drained liquid and if the water dissolves, it confirms that it is an aqueous layer). The alkyl halide was then returned to the separatory funnel. 14 mL of saturated aqeous sodium bicarbonate was added a little at a time while the separatory funnel was being swirled. A stopper was placed on the funnel and it was shaken for 1 minute while being vented frequently to relieve any pressure that was being produced. The lower alkyl halide layer was drained into a dry Erlenmeyer flask and 1.0 g of anhydrous calcium chloride was added to dry the solution. A stopper was placed on the Erlenmeyer flask and the contents were swirled until the liquid was clear. For the distillation

Solid impurities and liquid impurities having quite different boiling points are most easily removed by distillation, but even liquids having similar boiling points can be separated. For easy separations, a "simple distillation" apparatus (Figure 1) will be used for the first part, but for more accurate separations, a "fractional distillation" apparatus (Figure 2) is necessary. In this lab we will be using both apparatuses. Unfortunately, each time a distillation is run, material is lost. Some evaporates into the air and some is left behind, stuck to the apparatus. That is why fractional distillation is the best apparatus to use. It is important to keep a careful record of the temperature at the beginning and end of every fraction you collect. Stop the distillation by removing the heat just before all the liquid in the distilling flask is completely gone. Watching the rate of temperature increase is important, allowing the temperature to increase too quickly can cause impurity. The distillation curves for our simple and fractional distillation clearly demonstrate that fractional distillation separates the two compounds more

Me and my lab partner, obtained a mixture of a un known proportion from the instructor and then flow the guide line in our lab manual to separate the mixture by applying the separation method motioned in our lab manual pages 33-40 . In this experiment, the separation methods were decantation,

There are millions of different organic compounds. Most of them are found in mixtures and in order to achieve a pure form they need to be separated, isolated, and purified. However, there are endless numbers of possible mixtures, which make it impossible to have a pre-designed procedure for every mixture. So chemists often have to make their own procedures. The purpose of this experiment was to prepare the student to the real world by them designing their own procedure which will help them understand the techniques of separation and purification better. The goal was to extract two of the components of the

The objective of this extraction experiment was to achieve a comprehensive understanding, as well as master the practice, of the technique of separating various individual components of a compound.

Substance A and B were weighed; Substance A weighed 0.502 g and substance B weighed 0.503 g. Both substances were put into two different test tube with approximately 8 ml of DI water into the test tub. Substance A and B were stirred and B dissolved while A did not. This shows that B is soluble in water compared to A. Thus, shows that B is soluble in water than A. The reason why B is soluble in water is because it has a higher dipole moment than A. With a higher dipole moment, it shows that it is soluble in water since it is polar and the bonds were easily broken.

In this experiment, distillations were done. This is a technique that utilizes the differing boiling points of two or more compounds in a mixture in order to separate the compounds from the mixture. The way fractional distillation works is that the initial mixture is boiled up to the point of the lower boiling point compound; this compound then evaporates. This compound is then

In this experiment, a mixture of unknown #3 was used. That mixture had acid, base, and neutral. We added solvent to the unknown. It is important to know the density of the solvent in order to determine which is the aqueous layer and which is the organic layer. If the solvent that has more density than water, so the organic layer will be the lower layer, while if the solvent has lower density than water, the organic layer will be the upper layer. This will make an error if the determination of the layers was wrong after added the strong acid or the strong base. We added 5% HCl to the mixture in order to separate the base in the aqueous layer and form its salt. Same thing, we add 5% NaOH to the mixture in order to separate the acid and form its salt. In order to recover the base, we add 10% NaOH to the HCl extraction. The result will be salt with a base. Same thing for the acid, in order to recovered it, we added 10% HCl. The reaction will give us salt with an acid. For the neutral, we added sodium sulfate as a drying reagent in order to dry water and separate the neutral part as pure.

Simple distillation is a separation technique which can be used to separate and purify distillates from a liquid mixture which ideally contains one volatile and one non-volatile compound. If such ideal conditions are not possible—as is usually the case—then simple distillation can be applied as long as the liquid in question is composed of compounds that differ in volatility such that their boiling points differ by at least 40 to 50 degrees Celsius. Because

In the separating funnel, a heterogeneous mixture was formed: resulting in an organic layer (top) and a solvent layer (bottom). This effectively allowed the draining of the solvent, in order to isolate the organic layer, the impure ester (1-pentyl ethanoate)

The purpose of this experiment was to use solvent extraction techniques in order to separate a mixture consisting of a carboxylic acid (p-toulic acid), a phenol (p-tert-butylphenol), and a neutral compound (acetanilide). Extraction is the process of selectively dissolving one or more of the compounds of a mixture into an appropriate solvent, the solution that contains these dissolved compounds is called an extract (Manion, 2004).

     Conventional Liquid Chromatography is most commonly used in preparative scale work to purify and isolate some components of a mixture. It’s also used in ultra trace separations where small disposable columns are used once and then discarded. Analytical separations of solutions for detection or quantification typically use more sophisticated high-pressure liquid chromatography instruments.

Extraction vessels: Jars or bottles with sufficient capacity to hold the sample and extraction fluid. Two liter normal capacity bottles are recommended. The vessel type is determined by the analysis of interest.