Ap Chemistry Lab Report Ph Titration

4. To utilize the titration results to calculate the molarity of the hydrochloric acid and the

You find a sample of a solution that has a faint odor resembling vinegar. You are verifying that it is indeed vinegar and you add a few drops of phenolphthalein. The sample turns pink. What assumptions can you make about this sample?

An example would be pure water. Most of the time the pH is determined by pH paper but there are also other ways to determine the pH. For example, in this lab, cabbage juice was used. Cabbage juice is a great pH indicator because it can be homemade and easy to access.

3.0g of salicylic acid was weighed then 3.0mL of acetic anhydride and 6 drops of 85% H3PO4 were added to it. The mixture was warmed over a water bath for 5 minutes while stirring. After warming, 20 drops of distilled water was slowly added. 15mL of water was added then the solution was heated until it became clear. It was allowed to cool and was placed in an ice bath until the solution becomes cloudy. Using pre-weighed filter paper, the mixture was filtered and was allowed to dry in the filter paper.

pH was recorded every time 1.00 mL of NaOH was added to beaker. When the amount of NaOH added to the beaker was about 5.00 mL away from the expected end point, NaOH was added very slowly. Approximately 0.20 mL of NaOH was added until the pH made a jump. The pH was recorded until it reached ~12. This was repeated two more times. The pKa of each trial are determined using the graphs made on excel.

1. What was the purpose of using water as a sample in some of the tests performed in the lab? (2 points) to have a control.

twice. Place the pH probe in the beaker and record the pH in the data table. Drag the beaker to the red

Three grams of a mixture containing Benzoic Acid and Naphthalene was obtained and placed in 100 ml beaker and added 30 ml of ethyl acetate for dissolving the mixture. A small amount (1-2 drops) of this mixture was separated into a test tube. This test tube was covered and labelled as “M” (mixture). This was set to the side and used the following week for the second part of lab. The content in the beaker was then transferred into separatory funnel. 10 ml of 1 M NaOH added to the content and placed the stopper in the funnel. In the hood separatory funnel was gently shaken for approximately one minute and vent the air out for five seconds. We repeated the same process in the same manner one more time by adding 10ml of 1M NaOH.

The purpose of this experiment was to determine the pKa, Ka, and molar mass of an unknown acid (#14). The pKa was found to be 3.88, the Ka was found to be 1.318 x 10 -4, and the molar mass was found to be 171.9 g/mol.

3.6.3. 2, 4 – D (2, 4–Dichloro phenoxy acetic acid) stock solution (1mg/ml): 10.0mg of 2.4-D being weighed and dissolved completely in 1N NaOH to a final total volume

for percent acetic acid in vinegar, it can be concluded that the percentage of acetic acid in the

One milliliter of 6.00-M phosphoric acid was placed into a 125-mL Erlenmeyer flask using a volumetric pipette. Using a slightly larger pipette, six milliliters of 3.00-M sodium hydroxide was transferred into a 50-mL beaker. Then a disposable pipette was used to slowly mix the sodium hydroxide into the phosphoric acid while the solution was swirled around. Then both the beaker and flask were rinsed with 2-mL of deionized water and set aside. A clean and dry evaporating dish was weighed with watch glass on a scale. Then the solution was poured into the dish and the watch glass was placed on top. The solution was then heated with a Bunsen burner to allow for the water to boil off to reveal a dry white solid. After the dish cooled to room temperature it was once again weighed and the new mass was recorded.

By using acid-base titration, we determined the suitability of phenolphthalein and methyl red as acid base indicators. We found that the equivalence point of the titration of hydrochloric acid with sodium hydroxide was not within the ph range of phenolphthalein's color range. The titration of acetic acid with sodium hydroxide resulted in an equivalence point out of the range of methyl red. And the titration of ammonia with hydrochloric acid had an equivalence point that was also out of the range of phenolphthalein.. The methyl red indicator and the phenolphthalein indicator were unsuitable because their pH ranges for their color changes did not cover the equivalence points of the trials in which they were used. However, the

First, three titration curves and three second derivative curves were created to determine the average pH at the half-equivalence point from the acetic acid titrations. Titration curves were used as visuals to portray buffer capacity. The graphs and a table, Table 1, that showcased the values collected were created and included below. The flat region, the middle part, of Figures 1, 2 and 3, showed the zone at which the addition of a base or acid did not cause changes in pH. Once surpassed, the pH increased rapidly when a small amount of base, NaOH, was added to the buffer solution. Using the figures below and

2. Following solutions are added to the tubes and the pH of each tube is determined: