Basic Technologies of Handling Chemicals and Laboratory Apparatus

because each of the objects displaced the water by 1 mL, their mass over that mL is their density.

Procedure: I used a ruler, thermometer, and scale to take measurements. I used a graduated cylinder, short step pipet, scale, and ruler to determine volume and density. I used a volumetric flask, graduated pipet, pipet bulb, scale, and glass beaker to determine concentrations and densities of various dilutions.

Next, I poured distilled water just below the 250ml mark on the neck of the volumetric flask.

Density is the amount of matter per unit of measurement (Merriam-Webster. Merriam-Webster, n.d. Web. 26 Aug. 2016.). If water has a density of 1.0 g/mL and you place a substance with a density of 1.8 g/mL the substance will sink because it is denser than water. Density is often measured in g/cm^3 or g/mL because the formula for density is D=m/v.

I will be doing this experiment to understand density of water compared to the volume of an object. D=m/v=mass/volume

In this lab experiment our main focus was to get skillful in using tools such as the metric ruler, balances, thermometer, and graduated cylinder to capture measurements of length, mass, temperature and volume. Additionally, this lab helped us to become more familiar with the uncertainty of measurements, as well as becoming efficient with rounding our measurements to the correct numbers of significant figures. Our results are measured consistently with rounding to the closest answer we could possibly acquire as the data can tell you.

9. The accepted value for the density of water is 1 g/mL and the accepted density for isopropyl alcohol is 0.786 g/mL. Determine the percent error between your calculated densities and the accepted values for both water and isopropyl alcohol. Record the percent error in Data Table 4.

Measure 500ml of tap water in the 500cm3 beaker, then measure 5g of sodium hydrogen carbonate using the 50cm3 beaker and weight scale and place in the beaker of water, using the glass rod to dissolve it into the mixture.

2. In order to calculate the density of a solid or liquid sample, what measurements are needed?

Abstract: This experiment introduced the student to lab techniques and measurements. It started with measuring length. An example of this would be the length of a nickel, which is 2cm. The next part of the experiment was measuring temperature. I found that water boils around 95ºC at 6600ft. Ice also has a significant effect on the temperature of water from the tap. Ice dropped the temperature about 15ºC. Volumetric measurements were the basis of the 3rd part of the experiment. It was displayed during this experiment that a pipet holds about 4mL and that there are approximately 27 drops/mL from a short stem pipet. Part 4 introduced the student to measuring

When filling up the burette it is important that a funnel is used, however as the solution reaches the 0 mark it is ideal that the funnel be removed and a pipette used instead to reach the 0 mark, this is to achieve greater precision. During the experiment, it is important to swirl the flask continuously with one hand

2. Fill a flask with pure water (0% sugar), another with 0.2M water, another flask with 0.4 M water, and another flask with 0.8M water.

The volume of a small test tube and a thin-stemmed pipet were determined in this section of the lab. Water was poured into a small test tube until the water reached the very top edge of the test tube. The test tube was then emptied into a plastic 25 mL graduated cylinder and volume was measured and recorded into data table 3. A think-stemmed pipet was completely filled with water. Drops were carefully counted and emptied into the empty plastic 25 mL graduated cylinder until the water level reached 1 mL. The number of drops in 1 mL was recorded into data table 3. The thin-stemmed pipet had a total volume of 4 mL and that was also recorded into data table 3.

XII. Take the 250 ml beaker to your lab bench. Set up a gravity filtration with a plastic funnel, folded wet filter paper, and an Erlenmeyer flask. Pour the content in the 250 ml beaker slowly through the filter paper. Wash the filter paper with deionized water. Dispose of the filtrate in the proper labeled waste container.

Determine the weight of the water by subtracting the weight of the vial with water by the weight of the vial on its own.