Bottle Rocket Research Paper

Creating an optimal design that allowed my bottle rocket to go to the highest possible altitude and velocity was a long process that included lots of testing, trial, and error. With a rocket, I am attempting to test run and optimize the best design the allows the rocket to have an outstanding altitude and velocity. During this process of trial and error, I have organized my results by marking them down on multiple data table. I got my information from a bottle rocket simulator programmed by the National Aeronautics and Space Administration, more commonly known as NASA. The class attempted to run our own bottle rocket experiment, but this data was inconsistent because there were many variables that changed with each launch that we could not

First we measured out where the fins would go on the body of the rocket. Next we made the part of the rocket that would help it fly, i think it's called the motor mount tube. Afterwards we assembled the thrust rings onto the motor so it would fit in the body, and put tape around the nose cone. The motor was then placed into the tube. The fins went on next with some glue, and the launch lug so it can fly further. All of this was sealed with sealer. The last thing we did was place the wadding, and the parachute in the body, and we were good to go. Painted it all nice, and neatly. The rocket will launch when we put an igniter into the bottom, then you get a plug to make sure it is in there sturdy. You will then hook the wire’s from the control to the wires on the igniter, and then you're ready to

I began creating the base of the battering ram. I made holes in the middle of the round pieces of wood and put round thin pieces of wood through the middle of the circular pieces of wood to make the wheels. After the wheels

Ever been on a gas scooter? I have. It was by the most traumatic experience I have ever dealt with. Falling off not knowing the gas scooter didn’t have any brakes and hitting a car then falling off. Well, that was by far the most memorable day in my life. Ive never been in so much pain than that day, the worst experience ever.

Many people switch over to tankless gas hot water heaters believing them to be more efficient and energy-saving. However, it is important to realize that while a tankless gas hot water-heater can be more energy-efficient, they do not use significantly less energy than regular devises for heating water. If you only switching to a tankless gas hot water heater to save some money, then you will most likely be a bit disappointed.

The gas cap on your Saturn Vue is designed to keep your fuel in your vehicle and keep debris from getting into the fuel system. Anytime dirt, dust or other pollutants get into your fuel tank, they can become sucked up by the fuel pump and clog up the fuel filter. This may result in poor performance and bad fuel efficiency. A factory OEM gas cap will keep the tank sealed and secure. An OEM gas cap will be an exact fit, so there is no possibility of contamination getting in around the edges of the cap. At GMPartsCenter.net, we sell genuine GM parts only, so you know you are getting an exact fit replacement part for your Saturn.

The idea came to me of making a car that I could fit my dolls in. I started by drawing out a carefully thought out plan. Piece by piece, my project was coming together. I had to pace myself because I knew that it wasn't a one day project or even a week project. Sometimes, my calculations weren’t always accurate and pieces wouldn’t fit together as they should. I often had to cut pieces to make them fit into place.

To make the origami airplane correctly you need to follow these precise instructions. First, fold the paper in half and then unfold it. Next, fold the top two corners to the middle. After that, fold the two corners again. Then, fold in half again. Then, fold the wings out to the sides.Sixth, unfold the wings half way. After, glue the paper together where you folded so it does not fall apart. Last but not least, cut out cool designs.

Do you live in the country with a lot of property? There are many things you can typically do when out in the country that you cannot do in the city. A burn barrel is a good example. If you want to use one of these on your property, then consider customizing it to look like a wishing well.

If you've come up with a great invention you want to sell to the masses, the first step is to make a prototype. This allows you to visualize your invention in real life and see how well it functions. You may need to make alterations in the design until you're satisfied with the end result. Once the piece performs as you imagine, it's time to have it mass produced. Here are a few tips for bringing your design to life through the process of fabrication.

Last week, our class made water bottle rockets. We made them out of soda bottles. Some of us worked with a partner, but some didn’t. My partner and I made our rocket out of two 2-liter Pepsi bottles. We cut the top off of one of the bottles and glued it to the bottom of the other bottle so the rocket would fly better. We were supposed to put a piece of paper around the nose of the rocket, but our teacher told us it was unnecessary. We then cut out cardboard wings and hot glued them to our rocket. They would help the rocket fly instead of falling to the ground. Everybody had different shaped wings on their rocket, and I learned that the bigger the wings, the better the rocket flew. Some people even decorated their rocket. Our design process

The things that make me smile, get excited, or makes me want to do something is the level of complication or challenging which the things may have within the activities. The activities that involve Science, Technology, Engineering and Math that I find to be fun is the mousetrap car and the bottle rocket challenges which we are given due to the requirements and constraints which we are given. The requirements that are given in these activities help me to work with my team and acquaintances to get the task done and reach every aspect of the project which is being asked at hand. My organizational skills are put to work to go through every step and examine every part of the project which may include the instructions of putting the prototype together,

What is a rocket? well, a rocket is a cylindrical projectile that can be propelled to a great height or distance. Several early cultures used these rockets for some important things. Cultures such as Greek, Roman, Gellius, and the Early Chinese. They used them to shoot their arrows during the war. The rocketry was very important in America. The reason was because they were used for the “race to space” from 1957-1975.

All metal assembling incorporates a cementing procedure. The metal is either atomised to a powder, or it is thrown. There is a few throwing strategies utilized today. A considerable lot of the techniques utilize the shape once, for instance sand form throwing, the lost-wax strategy and accuracy throwing. For bigger amounts of fluid metal, there are essentially two techniques: ingot throwing and persistent throwing. Ingot throwing typically utilizes a perpetual form made by cast press secluded by clay material. There are confinements with the ingot throwing strategies. The structure in the focal point of the ingot will get coarse which diminishes the quality of the metal and when throwing bigger amounts of metal the treatment of the ingots gets

First, and the most important is a piece of paper because without the paper how are you going to make an airplane? Any paper will do find but make sure it’s not to flimsy so when making the airplane it doesn’t collapse when making the folds on the plane. Also, the bigger the paper the bigger folds you will have to make on the plane but that does mean the airplane will fly further then a regular piece of paper. Once you have the paper take one side of the