Bromination of Benzene Synthesis and Purification of Bromobenzene

Theory: One of the methods of preparing alkyl halides is via the nucleophilic substitution reactions of alcohols. Alcohols are inexpensive materials and easy to maintain. However, they are a poor leaving group the OH group is a problem in nucleophilic substitution, this problem is fixed by converting the alcohol into H2O.

Experiment 55 consists of devising a separation and purification scheme for a three component mixture. The overall objective is to isolate in pure form two of the three compounds. This was done using extraction, solubility, crystallization and vacuum filtration. The experiment was carried out two times, both of which were successful.

The first step that needed to be done in this experiment was adding hydrochloric acid (HCl)

The Purpose of this experiment is for the students to learn how to use sodium borohydride to reduce benzil to its secondary alcohol product via reduction reaction. This two-step reaction reduces aldehydes by hydrides to primary alcohols, and ketones to secondary alcohols. In order for the reaction to occur and to better control the stereochemistry and yield of the product, the metal hydride nucleophile of the reducing agents such as LiH, LiAlH4, or NaBH4 must be carefully chosen. Being that LiAlH4 and NaBH4 will not react with isolated carbon-carbon double bonds nor the double bonds from aromatic rings; the chosen compound can be reduce selectively when the nucleophile only react with

In the first acid extraction of benzocaine, the compound was dissolved in the organic solvent of dichloromethane. When the mixture was shaken with HCl, benzocaine’s amine group gained a proton and became more soluble in water than dichloromethane. This allowed the newly formed hydrochloric salt to migrate to the aqueous layer. However, the addition of NaOH to the acidic aqueous layer regenerated benzocaine by deprotonation, making it insoluble in the aqueous layer. The precipitation of an ionic salt was therefore recovered by vacuum filtration and had a tested melting point range of 85.1C-87.4C compared to 88C-90C, the literature melting point of benzocaine. The similarity in melting point ranges, but low percent yield of 30.37% proves that the extract was somewhat successful. Lower yields may be the result of spillage performed in the lab. In the second basic extraction, the organic layer now included benzoic acid and benzamide. When treated with NaOH to deprotonate benzoic acid, the newly formed sodium benzoate transitioned to the aqueous layer as a sodium salt. Benzoic acid is regenerated once again after the addition of HCl and became insoluble in the aqueous layer after protonation. Its precipitation was then filtered out for a 65.87% recovery. Compared to its literature melting point of 122.41C, the resulting 120.9C-123.5C melting range of the sample also supports the accuracy of the separation due to its similarities and high percent yield. In conclusion, the usage of base and acid liquid extraction was mostly successful in this experiment because it was able to efficiently and properly isolate the impure mixture into two separate components of benzocaine and benzoic acid. By performing the techniques of extraction and vacuum filtration, the similarities between literature and tested

Me and my lab partner, obtained a mixture of a un known proportion from the instructor and then flow the guide line in our lab manual to separate the mixture by applying the separation method motioned in our lab manual pages 33-40 . In this experiment, the separation methods were decantation,

12) Pipet the remaining methylene chloride to a new beaker. Place the flask in hot water bath, and boil the methylene chloride out, leaving the benzoin and the dibromobenzene .

The crude product was washed by taking the reaction product in the separatory funnel and adding 23 mL of deionized H2O. The mixture was shaken and allowed to settle until layers were observable. The top layer was the desired product and approximately 25 mL of aqueous layer was extracted from the separatory funnel. Next, 25 mL of 5% NaHCO3 was added to the separatory funnel in order to neutralize the acid. This mixture was swirled, plugged with the stopper and inverted. Built-up gas was released by turning the stopcock to its opened and closed positions, releasing CO2 by-product. This was done four times in one minute intervals. The solution was allowed to settle until layers were observable. The bottom layer that contained salt, base and water was extracted from the separatory funnel. The crude product was washed again as mentioned previously.

9.Repeat the procedure with a new mass of baking soda. Before beginning, rinse the reaction vessel with water. Refill the graduated cylinder with water. Check water level in collection box so it has room for the water from the graduated cylinder.

Once the distillate had been collected into two separate vials, both distillates were washed with aqueous sodium bicarbonate (1.5-ml, 5%). The aqueous layer (lower) was extracted from both vials using a pipette and put into a chemical waste bin. The organic (alkene) layer was then dried with anhydrous calcium chloride pellets (3 pellets per vial). Both distillates were analyzed using gas chromatography, and each peak shown was identified to be one of the alkenes. Analysis of the graph was used to determine the major and minor products of the reaction.

Wash (swirl and shake) the organic layer with one 10-mL portion of water and again drain the lower aqueous layer. Transfer the organic layer to a small, dry Erlenmeyer flask by pouring it from the top of the separatory funnel. Dry the crude t-pentyl chloride over 1.01 g of anhydrous calcium chloride until it is clear (see Technique 12, Section 12.9). Swirl the alkyl halide with the drying agent to aid the drying.

2) Rinse the solid with about 30 mL of distilled water and decant the liquid from the solid. It is critical that as little solid as possible is lost during this process. Repeat the rinsing two or three times.

After the initial mixture has refluxed, 9.11 grams of benzophenone was dissolved in 100 mL of anhydrous ether in a beaker and was then transferred into the separatory on the reflux apparatus. This solution was then added to the Grignard reagent at a drop wise rate while stirring. After the benzophenone was added, the mixture was then refluxed for 15 minutes on a heating mantle.

After the hour has passed, remove the tubes and add 2-3 drops of biuret reagent to each tube and shake.

1. Number four clean test tubes 1-4. 2. Place 1 ml (or 20 drops) of the following solutions into each tube: water, egg albumin, starch, and chicken broth. 3. Add 3 drops of Buiret reagent to each tube and gently shake