Carbohydrates Lab Report

The protein molecules in many foods provide the amino acid building blocks required by our own cells to produce new proteins. To determine whether a sample contains protein, a reagent called Biuret solution is used. Biuret solution contains copper ions. However, the chemical state of the copper ions in Biuret solution causes them to form a chemical complex with the peptide bonds between amino acids (when present), changing the color of the solution. Biuret solution is normally blue, but changes to pink when short peptides are present and to violet when long polypeptides are present.

1. Fill in the table below with the results from the monosaccharide test experiment, and your conclusions based on those results.

The null hypothesis will be that the test tubes with an increase in temperature, pH values, enzyme concentrations, and substrate concentration will have a very small color change or no color change at all. The alternate hypothesis is that the test tubes containing an increase in temperature, pH values, enzyme concentrations, and substrate concentration will all have an intense color change; the more the change, the more intense the color change will be.

Gelatin is observed to have a lower absorbance reading than lysozyme in only the Bradford assay, while in the BCA assay gelatin was observed to have about the same absorbance as lysozyme. In Bradford assay, the color yield for proteins with higher content of tryptophan, tyrosine, or cysteine residue, will be higher. The observed protein sensitivities did not correlates with the amino acid content in the Bradford assay. As presented in Table I, the mole fractions of lysine and arginine in BSA were 10 mole percent and 4 mole percent, respectively. The sensitivity should have been higher in BSA than in the Bradford assy. However, the observed sensitivities did correlates with the amino acid contents in the BCA assay.

Lab six requires students to observe the effects of pH and enzyme concentration on catecholase activity. Enzymes are organic catalysts that can affect the rate of a chemical reaction depending on the pH level and the concentration of the enzyme. As pH comes closer to a neutral pH the enzyme is at its greatest effectiveness. Also at the absorbance of a slope of 0.0122 the enzyme is affected greatly. The pH effect on enzymes can be tested by trying each pH level with a pH buffer of the same pH as labeled as the test tube and 1mL of potato juice, water, and catechol. This is all mixed together and put in the spectrophotometer to test how much is being absorbed at 420nm. As the effect on enzyme concentration can be tested almost the same way. This part of the exercise uses different amounts of pH 7-phosphate buffer and potato juice, and 1mL of catechol mixed together in a test tube. Each substance is put in the spectrophotometer at a wavelength set tot 420nm. The results are put down for every minute up to six minutes to see how enzyme concentration affects reaction rate. The results show that the pH 8 (0.494) affects the enzyme more than a pH of 4 (0.249), 6 (0.371), 7 (0.456), and 10 (0.126). Also the absorbance is greatest at a slope of 0.0122 with test tube C that has more effect on the reaction rate, than test tube A, B, and D.

2. Four unknown samples were included in the lab kit: flax seed meal, potato starch, egg whites, and dried milk. Using the results of the biochemical testing, determine which number corresponds to the correct unknown. (8 points)

During the

During

enzymes that will be used during this lab to test the ability of amylase to break down starch ,a

During the

In part II of the lab six small glass tubes were obtained in a test tube rack. Ten drops of distilled water were then added to test tube 1, five drops to tubes 2-4, and no drops in tubes 5 and 6. Five drops of 0.1M HCl were added to test tube 5 and five drops of 0.1M NaOH to test tube 6. Five drops of enzyme were then added to all tubes except tube 1. Tube 3 was then placed in the ice bucket and tube 4 was placed in the hot bucket at 80-900C for five minutes, the remaining tubes were left in the test tube rack. After the five minutes five drops of 1% starch was added to every tube and left to sit for ten minutes. After ten minutes five drops of DNSA were then added to all the tubes. All the tubes were then taken and placed in the

During these experimental procedures, the implication of multiple different temperatures on fungal and bacterial amylase was studied. In order to conduct this experiment, there were four different temperatures used. The four temperatures used were the following: 0 degrees Celsius, 25 degrees Celsius, 55 degrees Celsius, and 80 degrees Celsius - Each temperature for one fungal and one bacterial amylase. Drops of iodine were then placed in order to measure the effectiveness of the enzyme. This method is produced as the starch test. The enzyme was tested over the course of ten minutes to determine if starch hydrolysis stemmed. An effective enzyme would indicate a color variation between blue/black to a more yellowish color towards the end of the time intervals, whereas a not so effective enzyme would produce little to no change in color variation. According to the experiment, both the fungal amylase and bacterial amylase exhibited a optimal temperature. This was discovered by observing during which temperature and time period produced a yellow-like color the quickest. Amylase shared a similar optimal temperature of 55 degrees Celsius. Most of the amylases underwent changes at different points, but some enzymes displayed no effectiveness at all. Both amylases displayed this inactivity at 0 degrees Celsius. At 80 Celsius both the enzymes became denatured due to the high temperatures. In culmination, both fungal and bacterial amylase presented a array of change during it’s

* Temperature * Method of measuring solutions I will use equal amounts of trypsin, milk, PH, buffer and distilled water in all the experiments and will use the same measuring equipment to ensure fair representation of the effect of different PH on digestion.

Record observations: what color did the solution turn? Orange or blue/ black? This will tell whether the amylase is able to denature the starch solution Orange=Negative Blue/black= Positive

The purpose of this lab was to understand how different solutions played a role in the digestion protein. By looking at different variables, such as temperature, and pH we’re capable of understanding just how certain substances functioned and when they didn’t. The data for all labs are clear and concise and give a clear understanding of what solutions work best. All three labs were placed in a warm water bath set at 37’C to stimulate the reaction as if it were taking place within the human body. This gives us a more accurate reading on how they would react at that set temperature. We concluded why certain tubes changed to the color they did and further explained it. This lab focuses primarily on two crucial