Chemical Reaction Lab

The theoretical yield for the product is a necessary component in finding percent yield, and Eq. 2 and Calculation 2 demonstrate how it was found.

This experiment is based on determining the chemical formula for a hydrated compound containing copper, chloride, and water molecules in the crystal structure of the solid compound, using law of definite proportion. The general formula of the compound is CuxCly•zH2O, and aim is to determine chemical formula of this compound.

Washing of the copper is necessary in this experiment to separate the iron from the copper and make sure the iron is not counted in the mass of the copper.

The mixture was heated at 120°C using an aluminum block and was stirred gently. After all of the solid dissolved, it was heated for 20 additional minutes to ensure the reaction was complete.

5. Calculate the mass of the water by subtracting “Mass A” from “Mass B.” Record the mass of the water in Data Table 4.

Then 8.0g of copper sulfate crystals were placed inside the beaker and the mass was recorded for the actual crystals. 50 mL of water was added to the beaker with the crystals. The ring stand was set up with the wire mesh on it and one partner should place the mixture in the beaker on it should be heated without letting the mixture boil. Stir the mixture and heat until the crystals are dissolved. While one partner does this, the other should obtain 1.5g of iron filings in a measuring cup and records the mass. Then the iron filings should be added small amounts at a time to the heated solution. Stir continuously until all the mixture is added to the beaker. Then it sat for 10 minutes and observations were recorded. Record the mass of a filter paper and set up a filtration apparatus with the filter paper in a funnel over an Erlenmeyer flask. Decant the liquid through the paper slowly trying not to allow any solid to get on the filter paper. Then with de-ionized water, rinse your solid in the beaker and let the solid settle then decant the liquid. Repeat the washing twice more and in the last time guide all the solid into the filter paper. Then place the filter paper on a watch glass and then into a warm oven to dry. After it is cool, record the mass of the watch glass, filter paper and solid. If there is not enough time to cool, you may have to do it the next

The wet, crude product was placed into the 50 mL Erlenmeyer flask. Small amounts of CaCl2 were added to dry the solution. The flask was sealed and the mixture was swirled and left to settle. Once

I started with elemental copper metal and then reactions occur step by step as follows:

1) Allow the copper in the beaker to dry at low temperature in a drying oven for at least one hour.

Purpose: The purpose of this experiment was to observe the many physical and chemical properties of copper as it undergoes a series of chemical reactions. Throughout this process, one would also need to acknowledge that even though the law of conservation of matter/mass suggests that one should expect to recover the same amount of copper as one started with, inevitable sources of error alter the results and produce different outcomes. The possible sources of error that led to a gain or loss in copper are demonstrated in the calculation of percent yield (percent yield= (actual yield/theoretical yield) x 100.

The lab performed required the use of quantitative and analytical analysis along with limiting reagent analysis. The reaction of Copper (II) Sulfate, CuSO4, mass of 7.0015g with 2.0095g Fe or iron powder produced a solid precipitate of copper while the solution remained the blue color. Through this the appropriate reaction had to be determined out of the two possibilities. Through the use of a vacuum filtration system the mass of Cu was found to be 2.1726g which meant that through limiting reagent analysis Fe was determined to be the limiting reagent and the chemical reaction was determined to be as following:-

The purpose of this lab was to become familiar with the three different balances and two different methods used to find the weight and mass of chemicals and compounds in the ChemLab program. The lab was performed by using three different types of balances, and the direct weighing and weighing by difference methods.

Submerge the graduated cylinder in the plastic tub so that it is completely filled with water. Hold the open end of the graduated cylinder and move it vertically upside-down where the open end of the graduated cylinder is still submerged in the plastic tub. Clamp the graduated cylinder the ring stand of the lab table to keep it in place. perforate a hole in the top of the rubber cork for the solution container. Cut a straw the length of about four inches. place the straw inside of the rubber cork hole. Set up your timer for two minutes.

2. Add about 20 mL of distilled water and stir the mixture with a glass stirring rod to dissolve the sample. There may be a small amount of insoluble residue. If your sample does not dissolve completely, remove the insoluble material by filtration.

0.5% of copper sulphate solution was added by drop at a time and and the test tube was shaked continuously.