Comparing The Determination Of Molarity Of Naoh By Titration

1. To titrate a hydrochloric acid solution of “unknown” concentration with standardized 0.5M sodium hydroxide.

The purpose of this experiment is to determine an unknown concentration of acid (hydrochloric acid) with a standard solution of a base (sodium carbonate) using titration method.

The results showed the molarity of the NaOH solution. This experiment was completed twice and a new average molarity

After the twenty minutes elapsed, the flask was cooled to room temperature and then titrated with the remaining NaOH until the colorless solution remained pink. The final volume was then recorded. While solution #1 was heating the same process was repeated with solution#2 and the second burette

3. If a student did not remove all of the bubbles from inside the buret before reading the initial volume and beginning the titration, will this cause the calculated concentration of the hydrochloric acid determined from that trial to be higher or lower than the actual concentration? Explain your answer in complete

The next step in this lab is to rinse the Erlenmeyer flask with distilled water down the drain and then repeat the experiment, this time adding 10 ml of 0.10M KI and 10 ml of distilled water to the flask instead. The flask should again be swirling to allow the solution to succumb to the same temperature as the water bath and once it has reached the same temperature, 10 ml of 3% H2O2 must then be added and a stopper must be immediately placed on the flask and recording should then begin for experiment two. After recording the times, the Erlenmeyer flask must then be rinsed again with distilled water down the drain. After rinsing the flask, the last part of the lab can now be performed. Experiment three is performed the same way, but instead, 20 ml of 0.10 ml M KI and 5 ml of distilled water will be added and after the swirling of the flask, 5 ml of 3% H2O2 will be added. After the times have been recorded, data collection should now be complete.

Chemistry 102 is the study of kinetics – equilibrium constant. When it comes to the study of acid-base, equilibrium constant plays an important role that tells how much of the H+ ion will be released into the solution. In this lab, the method of titrimetry was performed to determine the equivalent mass and dissociation constant of an unknown weak monoprotic acid. For a monoprotic acid, it is known that pH = pKa + log (Base/Acid). When a solution has the same amount of conjugate base and bronsted lowry acid, log (Base/Acid) = 0 and pH = pKa. By recording the pH value throughout the titration process and determining the pH at half- equivalence point, the value of Ka can be easily calculated. In this experiment, the standardized NaOH solution has a concentration of 0.09834 M. The satisfactory sample size of known B was 0.2117 g. The average equivalent mass of the unknown sample was found to be 85.01 g, pKa was found to be 4.69, which was also its pH at half-equivalence point and Ka was found to be 2.0439×〖10〗^(-5). The error was 1.255% for equivalent mass and 0.11% for Ka. In other word, the experiment was very precise and accurate; the identity of the unknown sample was determined to be trans-crotonic by the method of titrimetry.

Methods: First, a burette, ring stand, clamp, and an empty flask were obtained. The burette, with the valve closed, was attached to the ring stand with a clamp, and the empty flask was placed below the burette. Next, 50mL of the NaOH solution were poured into the burette, and a small bit was drained into the empty flask to ensure that the tip of the burette was also full of NaOH solution. The volume of the NaOH in the burette was recorded. Next, approximately 0.6 grams of KHP were massed poured into an empty 125mL flask. Two drops of an indicator solution were added to the KHP

ii. The second part of the titration series involves titration of NaOH with Hydrochloric acid (HCL). Again, three reps of titration and a blank titration have to be completed. A volumetric pipet is used to measure 10.00mL of HCL into three labeled conical flasks. Then the flasks are filled with deionized water until about the 50mL mark. A buret is

To determine the concentrations in both parts, the change in pH is monitored for every added amount of 0.1035 M NaOH. The pH of the solution is taken using the Orion Model 420A pH reader. The data for Figures 1-4 can be found in Appendix. B.

Its concentration was found through a quantitative and qualitative titration testing. Because HCl is acidic, a 1.07M NaOH solution was used to titrate an aqueous solution of HCl (the unknown solution). The PASCO program gave the final results shown in Figure 1. A typical titration curve can be described as starting at the initial pH of the solution, then some acid/base is added, until a sharp curve either up or down takes the pH past a neutral of 7, and towards the pH level of whatever the added acid’s/base’s pH is (Clark6). The stronger the acid or base being titrated, the faster the change occurs, which means a sharper slope of the titration graph. Also, it is important to note the equivalence point on this titration graph. At the equivalence point “the correct amount of standard solution must be added to fully react with the unknown concentration” (Xavier3). In Figure 1, this equivalence point is shown by where the sharpest slope occurs in the curve, which is seen at about a pH of 5.0

During a titration the pH of the solution will be monitored using a pH meter from that we get a titration curve. The titration curve is then used to determine the equivalent molecular weight and Ka value of the unknown weak acid, from that we are

5. In reaction three, the number of moles of NaOH can be calculated from the concentration of the solution (1.0M = 1.0mole/L) and the volume used. The calculation is below. Enter the result into Data Table 2.

The purpose of this lab was to use process titration to find concentration of an aqueous solution of Hcl(aq) , using KOH(aq) as the titrant.

An acid-base titration is the determination of the concentration of an acid or base by exactly neutralizing the acid/base with an acid or base of known concentration. This allows for quantitative analysis of the concentration of an unknown acid