Copper Carbonate Lab Report

This experiment is based on determining the chemical formula for a hydrated compound containing copper, chloride, and water molecules in the crystal structure of the solid compound, using law of definite proportion. The general formula of the compound is CuxCly•zH2O, and aim is to determine chemical formula of this compound.

In this task the concentration of an unknown sample of copper sulphate using colorimetry was used to find the concentration. In this investigation copper sulphate was used which is CuSO4.5H20 as a formula. To make a standard solution which was 1M, the same clean equipment was used to make up the standard solution as used to make sodium carbonate. However there was one difference and that was that the hot distilled water was used to dissolve the copper sulphate crystals. There had to be enough hot water in order to dissolve the crystals into the beaker and then add cold distilled water to cool the solution.

The purpose of the experiment is to cycle solid copper through a series of five reactions. At different stages of the cycle, copper was present in different forms. First reaction involves reaction between the copper and nitric acid, and copper changed from elemental state to an aqueous. The second reaction converted the aqueous Cu2+ into the solid copper (2) hydroxide. In the third reaction Cu(OH)2 decomposed into copper 2 oxide and water when heated. When solid CuO reacted with sulfuric acid, the copper returned to solution as an ion (Cu2+). The cycle of reactions was completed with the reaction where elemental copper was regenerated by Zn and Cu

The Cu Later lab experiment is designed to allow you to practice lab skills in implementing and performing a series of reactions. Specifically, four types of chemical reactions will occur: oxidation/reduction; double replacement; single replacement; and decomposition. You will begin with a known amount of copper metal, which, after progressing through several steps, is reproduced. In this experiment you will observe and record the various changes such as heat, color changes, and production that occur. This procedure is used to observe some chemical reactions of copper and its compounds while also performing the lab appropriately as to retain the copper as much as

The purpose of this lab was to determine the limiting reactant in a reaction between copper sulfate and iron. Using the reaction between copper sulfate and iron, the reaction was observed to see the reaction and transformation of matter. The copper sulfate was placed into a beaker, as the excess reactant, then iron filings added until the heated solution was completely reacted. This reaction created an excess of leftover. The law of conservation of mass can be observed in this reaction, and using the data found, the percent yield calculated.

Heavy precipitate emerged immediately and solution turned white in color; solution then became opaque and turned light, bright blue in color.

The purpose of this lab was to determine the percent cobalt and oxalate by mass, and with that information, the empirical formula for cobalt oxalate hydrate, using the general formula Coa(C2O4)b.cH2O.

13) When the tray is thoroughly dry, determine its mass. Record the mass in the data table. You have to wait until day three to weigh the copper.

Before the synthesis of the Copper Iodine Compound, the identities provided (CuNO3)2 and Nal weighed 1.65 g and 4.7 g, respectively. After being weighed, the (CuNO3)2 exhibited a blue color, while the Nal, through observation, was a white color. However, when both identities were combined, the product turned into a brown and red rocky material. Once 20 mL of deionized water was added, the product quickly turned pale pink paste. After the solution was repeatedly washed with a total of an additional 100 mL of deionized water, the product was powdery and pink with small grains, and was left to air-dry. Once the product was air dried, it was observed to be a pale pink color, while the filter paper was stiff as the product was hard and dry. Therefore, the solid was scraped off onto a recrystallizing dish. However, the mass of an empty recrystallizing dish needed to be recorded in order to compare how much of the synthesized copper iodide was obtained. Within this case, the empty recrystallizing dish used weighed 32.01 g, the product on the empty dish weighed 1.03 g, having a total weight of 33.04 g.

The Copper Cycle is a popular experiment used to determine if an element, in this instance, copper, reverts to its elemental form after a chain of reactions. This experiment is very dangerous because of the reactions between the strong acids and bases. In this experiment I performed a series of reactions starting with copper metal and nitric acid to form copper (II) nitrate. Then I reacted copper and several other solutions such as, sodium hydroxide, sulfuric acid, ammonium hydroxide, and hydrochloric acid to form precipitates. In conclusion my percent recovery

Purpose: The purpose of this experiment was to observe the many physical and chemical properties of copper as it undergoes a series of chemical reactions. Throughout this process, one would also need to acknowledge that even though the law of conservation of matter/mass suggests that one should expect to recover the same amount of copper as one started with, inevitable sources of error alter the results and produce different outcomes. The possible sources of error that led to a gain or loss in copper are demonstrated in the calculation of percent yield (percent yield= (actual yield/theoretical yield) x 100.

The lab performed required the use of quantitative and analytical analysis along with limiting reagent analysis. The reaction of Copper (II) Sulfate, CuSO4, mass of 7.0015g with 2.0095g Fe or iron powder produced a solid precipitate of copper while the solution remained the blue color. Through this the appropriate reaction had to be determined out of the two possibilities. Through the use of a vacuum filtration system the mass of Cu was found to be 2.1726g which meant that through limiting reagent analysis Fe was determined to be the limiting reagent and the chemical reaction was determined to be as following:-

The volume of carbon dioxide gas produced from a reaction was measured in order to determine what carbonate sample was used. A gas assembly apparatus was used to capture the gas from a reaction between an unknown carbonate and 6M hydrochloric acid; three trials were performed. The mass of the unknown carbonate was determined, and the reaction occurred in a test tube. The volume of gas produced by the reaction was measured, and the partial pressure of carbon dioxide was calculated after the partial pressure of water vapor was determined using Dalton’s Law of Partial Pressures. The percent mass of carbon dioxide gas was then calculated, and the average mass percent was compared to the table of known carbonates. It was concluded that the unknown carbonate sample used in the reaction was magnesium carbonate.

Solutions of CuSO45H2O (0.506 g in 10mL water, 3.17E-3 mol) and ammonium peroxodisulfate (1.030 g in 10mL water, 4.51E-3 mol) were prepared and mixed

Copper is used as it has the lowest affinity and solubility of carbon, as it does not form a carbide phase, relative to Ni and Co . This is attributed to copper’s filled 3d electron shell, possessing an electron configuration of [Ar] 3d104s1, which due to its symmetrical electronic configuration reduces reciprocal electronic repulsions. In addition, copper is able to transfer charge from the π electrons of the sp2 carbons to the empty 4s orbital of