Copper Phosphate Trihydrate Lab Report

Theoretical Yield: The amount of the product obtained when all of the limiting reagent react.

In chemical reactions, the significance of knowing the limiting reactant is high. In order to increase the percent yield of product, increasing the limiting reactant, possibly, is the most effective. In this experiment we were able to calculate limiting reactants from the reaction of CaCl2. 2H2O + K2C2O4.H2O(aq).

In this task the concentration of an unknown sample of copper sulphate using colorimetry was used to find the concentration. In this investigation copper sulphate was used which is CuSO4.5H20 as a formula. To make a standard solution which was 1M, the same clean equipment was used to make up the standard solution as used to make sodium carbonate. However there was one difference and that was that the hot distilled water was used to dissolve the copper sulphate crystals. There had to be enough hot water in order to dissolve the crystals into the beaker and then add cold distilled water to cool the solution.

The purpose of the experiment is to cycle solid copper through a series of five reactions. At different stages of the cycle, copper was present in different forms. First reaction involves reaction between the copper and nitric acid, and copper changed from elemental state to an aqueous. The second reaction converted the aqueous Cu2+ into the solid copper (2) hydroxide. In the third reaction Cu(OH)2 decomposed into copper 2 oxide and water when heated. When solid CuO reacted with sulfuric acid, the copper returned to solution as an ion (Cu2+). The cycle of reactions was completed with the reaction where elemental copper was regenerated by Zn and Cu

1. Suppose that you have an unlimited supply of copper (II) sulfate to react with iron. How many moles of copper would be

The Cu Later lab experiment is designed to allow you to practice lab skills in implementing and performing a series of reactions. Specifically, four types of chemical reactions will occur: oxidation/reduction; double replacement; single replacement; and decomposition. You will begin with a known amount of copper metal, which, after progressing through several steps, is reproduced. In this experiment you will observe and record the various changes such as heat, color changes, and production that occur. This procedure is used to observe some chemical reactions of copper and its compounds while also performing the lab appropriately as to retain the copper as much as

The purpose of this lab was to determine the limiting reactant in a reaction between copper sulfate and iron. Using the reaction between copper sulfate and iron, the reaction was observed to see the reaction and transformation of matter. The copper sulfate was placed into a beaker, as the excess reactant, then iron filings added until the heated solution was completely reacted. This reaction created an excess of leftover. The law of conservation of mass can be observed in this reaction, and using the data found, the percent yield calculated.

Before the synthesis of the Copper Iodine Compound, the identities provided (CuNO3)2 and Nal weighed 1.65 g and 4.7 g, respectively. After being weighed, the (CuNO3)2 exhibited a blue color, while the Nal, through observation, was a white color. However, when both identities were combined, the product turned into a brown and red rocky material. Once 20 mL of deionized water was added, the product quickly turned pale pink paste. After the solution was repeatedly washed with a total of an additional 100 mL of deionized water, the product was powdery and pink with small grains, and was left to air-dry. Once the product was air dried, it was observed to be a pale pink color, while the filter paper was stiff as the product was hard and dry. Therefore, the solid was scraped off onto a recrystallizing dish. However, the mass of an empty recrystallizing dish needed to be recorded in order to compare how much of the synthesized copper iodide was obtained. Within this case, the empty recrystallizing dish used weighed 32.01 g, the product on the empty dish weighed 1.03 g, having a total weight of 33.04 g.

The Copper Cycle is a popular experiment used to determine if an element, in this instance, copper, reverts to its elemental form after a chain of reactions. This experiment is very dangerous because of the reactions between the strong acids and bases. In this experiment I performed a series of reactions starting with copper metal and nitric acid to form copper (II) nitrate. Then I reacted copper and several other solutions such as, sodium hydroxide, sulfuric acid, ammonium hydroxide, and hydrochloric acid to form precipitates. In conclusion my percent recovery

Purpose: The purpose of this experiment was to observe the many physical and chemical properties of copper as it undergoes a series of chemical reactions. Throughout this process, one would also need to acknowledge that even though the law of conservation of matter/mass suggests that one should expect to recover the same amount of copper as one started with, inevitable sources of error alter the results and produce different outcomes. The possible sources of error that led to a gain or loss in copper are demonstrated in the calculation of percent yield (percent yield= (actual yield/theoretical yield) x 100.

The lab performed required the use of quantitative and analytical analysis along with limiting reagent analysis. The reaction of Copper (II) Sulfate, CuSO4, mass of 7.0015g with 2.0095g Fe or iron powder produced a solid precipitate of copper while the solution remained the blue color. Through this the appropriate reaction had to be determined out of the two possibilities. Through the use of a vacuum filtration system the mass of Cu was found to be 2.1726g which meant that through limiting reagent analysis Fe was determined to be the limiting reagent and the chemical reaction was determined to be as following:-

We used the equation M1V1= M2V2 to find the proper volume to get the correct molarity of solution. The original phosphate is .101M and was diluted to .0002M. The phosphate and the reagent ammonium vanadomolybdate (AVM) are then prepared in a 2:1 solution for the spectrophotometer 20 to read it in a cuvette. A cuvette of water and AVM was also prepared in a 2:1 ratio to act as the blank for the PO4/AVM solution.

Stoichiometry is a method scientists use to presume how two or more substances will react together. In order to do so successfully, the reactants are positioned on the left and the products on the right. The most important part of successfully

Introduction: Metallic copper and its compounds have played an important role in history, from ancient civilizations to today’s economy. It also has biological and environmental significance. In this experiment, we explored copper in its metallic and ionic forms and examined the reactions which form metallic copper and copper compounds as well as calculated percentage yield of final metallic copper product. Materials and Methods:

At the end of the experiment when the lid was removed, it was found out that the blue colour of the copper (II) sulphate solution has faded away. It was turned to pale grey and there were some precipitates present. It was the zinc powder that was in excess to ensure that the copper (II) sulphate solution could react fully with the zinc powder.