Describe The Evolution Of The Calculated Concentration Of Hcl

We know that that the end point of the titration is reached when, after drop after careful drop of NaOH, the solution in the flask retains its pale pink color while swirling for about 30

2. To titrate a hydrochloric acid solution of “known” concentration with standardized 0.5M sodium hydroxide.

The Distilled water pH average of HCl for zero drops was 6.67, and the pH for the final thirtieth drop

pH was recorded every time 1.00 mL of NaOH was added to beaker. When the amount of NaOH added to the beaker was about 5.00 mL away from the expected end point, NaOH was added very slowly. Approximately 0.20 mL of NaOH was added until the pH made a jump. The pH was recorded until it reached ~12. This was repeated two more times. The pKa of each trial are determined using the graphs made on excel.

In 2 and 7 I added 50 mL of .1 M NaCl. I added sodium acetate to the rest of the beakers: 1 gram to 3 and 8, 5 grams to 4 and 9, and 10 grams to 5 and 10. I then filled the beakers that contained the solid sodium acetate with 50 ml of .10 M acetic acid. Specifics can be found on page 84 of the lab manual. Though the lab manual instructed to use a pipet, we did not have an accurate 1 mL pipet or a graduated pipet, so we instead prepared two graduated burets with 1 M Sodium Hydroxide and 1 M hydrochloric acid. Using a standardized pH probe with a Lab Pro to measure changes in pH, we added 1 mL of HCl at a time and recorded the changes. The same was done for the NaOH.

Question: The equivalence points of the two titration curves were not in the same pH range. Explain. (Why was the pH at the equivalence point different for the two different acids?)

To improve the results from the experiment buffer solutions that were not whole pHs could have been used e.g. pH 4.5, 5.5 etc. This would have provided more reliable results as a wider range of results would have been produced. Using pHs with decimals would also help to more accurately determine the optimum pH as the optimum may have been above or below the pH stated in the hypothesis; 8. In this experiment however the optimum is taken at 8 because the graph does not rise again.

When using different methods to measure pH levels there are some tools that can be useful. Some more than others but by putting into action the different methods it may determine which tools will work best and give the best results when testing the pH within a solution. The pH, which stands for the proportion of hydrogen ions in a solution, could be acidic (acidosis), neutral or basic (alkaline). The pH scale goes from numbers 1 through 14. A pH of 7 is neutral;

Chemistry 102 is the study of kinetics – equilibrium constant. When it comes to the study of acid-base, equilibrium constant plays an important role that tells how much of the H+ ion will be released into the solution. In this lab, the method of titrimetry was performed to determine the equivalent mass and dissociation constant of an unknown weak monoprotic acid. For a monoprotic acid, it is known that pH = pKa + log (Base/Acid). When a solution has the same amount of conjugate base and bronsted lowry acid, log (Base/Acid) = 0 and pH = pKa. By recording the pH value throughout the titration process and determining the pH at half- equivalence point, the value of Ka can be easily calculated. In this experiment, the standardized NaOH solution has a concentration of 0.09834 M. The satisfactory sample size of known B was 0.2117 g. The average equivalent mass of the unknown sample was found to be 85.01 g, pKa was found to be 4.69, which was also its pH at half-equivalence point and Ka was found to be 2.0439×〖10〗^(-5). The error was 1.255% for equivalent mass and 0.11% for Ka. In other word, the experiment was very precise and accurate; the identity of the unknown sample was determined to be trans-crotonic by the method of titrimetry.

ii. The second part of the titration series involves titration of NaOH with Hydrochloric acid (HCL). Again, three reps of titration and a blank titration have to be completed. A volumetric pipet is used to measure 10.00mL of HCL into three labeled conical flasks. Then the flasks are filled with deionized water until about the 50mL mark. A buret is

Within an acid-base titration the titration curve resembles the strengths of the corresponding acids and bases. A strong acid will correspond with a weak conjugate base, and a weak conjugate acid will correspond with a strong base. This is based on the Bronsted-Lowry model. The weak acid will donate protons to the hydroxide ion. Weak acids will have a low Ka value, the Ka value is the tendency of the acid to dissociate:

Using Graph 1: The Volume of Titrant Added in order to reach the Endpoint and the Corresponding pH Values, observe the vertical line of each titration and see the points in which the horizontal lines intersect it. These points give the

In the first experiment my partner and I selected to produce a buffer that contained 35mL of .1 M sodium acetate with 10 mL of .2M acetic acid with the excepted pH of the solution to be 5. We used C1V1=C2V2 to first calculate the theoretical concentration of both the weak acid and the weak base in the buffer solution. Then using the theoretical concentration and the Henderson- Hasselbalch equation we were able to calculate the excepted pH. After calculating the pH we then measured the experimental pH of the produced buffer and found it to be 4.9. This showcased that there was a difference of 2% between the theoretical pH and the experimental pH. We further measured the buffering capacity of three different samples one being the buffer that

First, three titration curves and three second derivative curves were created to determine the average pH at the half-equivalence point from the acetic acid titrations. Titration curves were used as visuals to portray buffer capacity. The graphs and a table, Table 1, that showcased the values collected were created and included below. The flat region, the middle part, of Figures 1, 2 and 3, showed the zone at which the addition of a base or acid did not cause changes in pH. Once surpassed, the pH increased rapidly when a small amount of base, NaOH, was added to the buffer solution. Using the figures below and

2. Following solutions are added to the tubes and the pH of each tube is determined: