Determining Enthalpy Change of a Displacement Reaction

Due to this fact, the concentration of copper in the solution is able to be calculated by using light absorbance. Since zinc doesn’t absorb any light, we are able to deduce that the greater the absorbance, the greater the concentration of copper.

It is a chemical reaction where the colors of both solution and iron strip changed. It is

In this task the concentration of an unknown sample of copper sulphate using colorimetry was used to find the concentration. In this investigation copper sulphate was used which is CuSO4.5H20 as a formula. To make a standard solution which was 1M, the same clean equipment was used to make up the standard solution as used to make sodium carbonate. However there was one difference and that was that the hot distilled water was used to dissolve the copper sulphate crystals. There had to be enough hot water in order to dissolve the crystals into the beaker and then add cold distilled water to cool the solution.

The purpose of the experiment is to cycle solid copper through a series of five reactions. At different stages of the cycle, copper was present in different forms. First reaction involves reaction between the copper and nitric acid, and copper changed from elemental state to an aqueous. The second reaction converted the aqueous Cu2+ into the solid copper (2) hydroxide. In the third reaction Cu(OH)2 decomposed into copper 2 oxide and water when heated. When solid CuO reacted with sulfuric acid, the copper returned to solution as an ion (Cu2+). The cycle of reactions was completed with the reaction where elemental copper was regenerated by Zn and Cu

Washing of the copper is necessary in this experiment to separate the iron from the copper and make sure the iron is not counted in the mass of the copper.

Obtain a 50 mL beaker for the experiment. In the first part of the experiment, you dissolve the zinc core of a penny and leave the copper covering intact by putting four notches in

The Cu Later lab experiment is designed to allow you to practice lab skills in implementing and performing a series of reactions. Specifically, four types of chemical reactions will occur: oxidation/reduction; double replacement; single replacement; and decomposition. You will begin with a known amount of copper metal, which, after progressing through several steps, is reproduced. In this experiment you will observe and record the various changes such as heat, color changes, and production that occur. This procedure is used to observe some chemical reactions of copper and its compounds while also performing the lab appropriately as to retain the copper as much as

When the zinc was dropped in the hydrochloric acid, the substance began bubbling vigorously, forming a precipitate. Eventually, the zinc dissolved completely. After the lit wooden splint broke the surface of the test tube, there was a loud popping noise. The gas that was released was hydrogen from the acid and the popping noise was a result of the Hydrogen being burned up by the fire creating a small explosion. Two chemical changes occurred in this test: one with the formation of a precipitate (a textbook sign of a chemical change), and the other when the explosion

Product bubbled upon addition to the hydrochloric acid; liquid turned cloudy ¡V precipitate was present; zinc sample disintegrated slowly and turned black in color.

-If the copper metal is submerged in the silver nitrate solution then in reaction, a pure, solid (Ag) silver product is created with an excess of (Cu (NO3)2) copper (II) aqueous liquid because a single displacement reaction occurs where the balance equation is then

Before the synthesis of the Copper Iodine Compound, the identities provided (CuNO3)2 and Nal weighed 1.65 g and 4.7 g, respectively. After being weighed, the (CuNO3)2 exhibited a blue color, while the Nal, through observation, was a white color. However, when both identities were combined, the product turned into a brown and red rocky material. Once 20 mL of deionized water was added, the product quickly turned pale pink paste. After the solution was repeatedly washed with a total of an additional 100 mL of deionized water, the product was powdery and pink with small grains, and was left to air-dry. Once the product was air dried, it was observed to be a pale pink color, while the filter paper was stiff as the product was hard and dry. Therefore, the solid was scraped off onto a recrystallizing dish. However, the mass of an empty recrystallizing dish needed to be recorded in order to compare how much of the synthesized copper iodide was obtained. Within this case, the empty recrystallizing dish used weighed 32.01 g, the product on the empty dish weighed 1.03 g, having a total weight of 33.04 g.

I started with elemental copper metal and then reactions occur step by step as follows:

Purpose: The purpose of this experiment was to observe the many physical and chemical properties of copper as it undergoes a series of chemical reactions. Throughout this process, one would also need to acknowledge that even though the law of conservation of matter/mass suggests that one should expect to recover the same amount of copper as one started with, inevitable sources of error alter the results and produce different outcomes. The possible sources of error that led to a gain or loss in copper are demonstrated in the calculation of percent yield (percent yield= (actual yield/theoretical yield) x 100.

The lab performed required the use of quantitative and analytical analysis along with limiting reagent analysis. The reaction of Copper (II) Sulfate, CuSO4, mass of 7.0015g with 2.0095g Fe or iron powder produced a solid precipitate of copper while the solution remained the blue color. Through this the appropriate reaction had to be determined out of the two possibilities. Through the use of a vacuum filtration system the mass of Cu was found to be 2.1726g which meant that through limiting reagent analysis Fe was determined to be the limiting reagent and the chemical reaction was determined to be as following:-

The main purpose of this experiment was to show that single displacement reactions between metals according to their reactivity, with more reactive elements having the power to displace less reactive elements and take their place in a chemical compound (Beran, 2014). This was supported by the results of the experiment, where solid metals were combined with aqueous solutions that contained another element, and reactions only took place when the solid metal was more reactive than the other element in the compound. Only three attempted trials resulted in a failure to produce a reaction, namely the combinations of copper with hydrochloric acid, and copper with nickel sulfate. The outcomes of these trials are justifiably reasonable because copper is ranked lower in the