Determining The Molecular Formula Of A Hydrated Copper Sulfate

A hydrate is a compound that is bonded with a certain number of water molecules. When heated, the water will be driven out, thus being left with an anhydrate. The anhydrate is the hydrate minus the water. The hydrate must be

This experiment is based on determining the chemical formula for a hydrated compound containing copper, chloride, and water molecules in the crystal structure of the solid compound, using law of definite proportion. The general formula of the compound is CuxCly•zH2O, and aim is to determine chemical formula of this compound.

In this task the concentration of an unknown sample of copper sulphate using colorimetry was used to find the concentration. In this investigation copper sulphate was used which is CuSO4.5H20 as a formula. To make a standard solution which was 1M, the same clean equipment was used to make up the standard solution as used to make sodium carbonate. However there was one difference and that was that the hot distilled water was used to dissolve the copper sulphate crystals. There had to be enough hot water in order to dissolve the crystals into the beaker and then add cold distilled water to cool the solution.

In this experiment an elemental copper was cycled a series of five reactions where it ended with pure elemental copper as well, but at different stages of the cycle the copper was in different forms. In the first reaction, elemental copper was reacted with concentrated nitric acid where copper changed the form from solid to aqueous. Second reaction then converted the aqueous Cu2+ into the solid copper II hydroxide (Cu(OH)2) through reaction with sodium hydroxide. The third reaction takes advantage of the fact that Cu(OH)2 is thermally unstable. When heated, Cu(OH)2 decomposes (breaks down into smaller substances) into copper II oxide and water. When the solid CuO is reacted with sulfuric acid, the copper is returned to solution as an ion (Cu2+). The cycle of reactions is completed with the

The mole is a convenient unit for analyzing chemical reactions. Avogadro’s number is equal to the mole. The mass of a mole of any compound or element is the mass in grams that corresponds to the molecular formula, also known as the atomic mass. In this experiment, you will observe the reaction of iron nails with a solution of copper (II) chloride and determine the number of moles involved in the reaction. You will determine the number of moles of copper produced in the reaction of iron and copper (II) chloride, determine the number of moles of iron used up in the reaction of iron and copper (II) chloride, determine the ratio of moles of iron to moles of copper, and determine the number of atoms and formula units involved in

The mass of the water was found by subtracting the original mass of the hydrate by the anhydride, that was found after heating the hydrate and evaporating the water. However, if the hydrate was not fully heating and there was still excess water remaining, this excess water mass would be included in the anhydride mass. This would make the mass of the anhydride larger and the mass of the water smaller. If the mass of the water was smaller, then the amount of moles of water would also be smaller. The mole ratio of anhydride to water would be larger because the denominator in the ratio, water in this case, would be smaller, so the entire ratio would essentially increase. This would mean that the number of molecules of water would be smaller as a result.

The mass percent of water was determined using the mass of water and dividing it by the total mass of the hydrate and then multiplying that answer by 100%. The number of moles of water in a hydrate was determined by taking the mass of the water released and dividing it by the molar mass of water. The number of moles of water and the number of moles of the hydrate was used to calculate the ratio of moles of water to moles of the sample. This ratio was then used to write the new and balanced equation of the dehydration process. The sample was then rehydrated to the original state and the percent of the hydrate recovered was calculated by using the mass of the rehydrated sample by

A hydrate is a chemical compound containing salt and water. Depending on the salt, there is a maximum amount of water molecules that can be absorbed by the salt. An anhydrous salt is when the hydrate loses water, which happens when the hydrate is heated

The purpose of this lab was to determine the percent cobalt and oxalate by mass, and with that information, the empirical formula for cobalt oxalate hydrate, using the general formula Coa(C2O4)b.cH2O.

The purpose of this experiment is to distinguish the relationships between reactants and products, in addition to expanding on concepts such as single displacement reactions, mole ratio values, moles to mass, theoretical yields, limiting reactants, excess, stoichiometric relationships and percentage errors.

Before the synthesis of the Copper Iodine Compound, the identities provided (CuNO3)2 and Nal weighed 1.65 g and 4.7 g, respectively. After being weighed, the (CuNO3)2 exhibited a blue color, while the Nal, through observation, was a white color. However, when both identities were combined, the product turned into a brown and red rocky material. Once 20 mL of deionized water was added, the product quickly turned pale pink paste. After the solution was repeatedly washed with a total of an additional 100 mL of deionized water, the product was powdery and pink with small grains, and was left to air-dry. Once the product was air dried, it was observed to be a pale pink color, while the filter paper was stiff as the product was hard and dry. Therefore, the solid was scraped off onto a recrystallizing dish. However, the mass of an empty recrystallizing dish needed to be recorded in order to compare how much of the synthesized copper iodide was obtained. Within this case, the empty recrystallizing dish used weighed 32.01 g, the product on the empty dish weighed 1.03 g, having a total weight of 33.04 g.

I started with elemental copper metal and then reactions occur step by step as follows:

Purpose: The purpose of this experiment was to observe the many physical and chemical properties of copper as it undergoes a series of chemical reactions. Throughout this process, one would also need to acknowledge that even though the law of conservation of matter/mass suggests that one should expect to recover the same amount of copper as one started with, inevitable sources of error alter the results and produce different outcomes. The possible sources of error that led to a gain or loss in copper are demonstrated in the calculation of percent yield (percent yield= (actual yield/theoretical yield) x 100.

The lab performed required the use of quantitative and analytical analysis along with limiting reagent analysis. The reaction of Copper (II) Sulfate, CuSO4, mass of 7.0015g with 2.0095g Fe or iron powder produced a solid precipitate of copper while the solution remained the blue color. Through this the appropriate reaction had to be determined out of the two possibilities. Through the use of a vacuum filtration system the mass of Cu was found to be 2.1726g which meant that through limiting reagent analysis Fe was determined to be the limiting reagent and the chemical reaction was determined to be as following:-

Determine how many grams of Copper Sulfate Pentahydrate you will need for your 100 mL of Water using the solubility curve. (See solubility curve)