Empirical Formula Lab

Ratio between the amounts in moles of any two compounds involved in a chemical reaction.

Empirical formulas represent the ratio of atoms in a formula. It is expressed in the simplest, small, whole number ratio. The molecular formula can either be the empirical formula, or a multiple of the empirical

Due to this fact, the concentration of copper in the solution is able to be calculated by using light absorbance. Since zinc doesn’t absorb any light, we are able to deduce that the greater the absorbance, the greater the concentration of copper.

Mole of chlorine : 1.0217g - .221g - .3946 g = .4061 g of chlorine

After this, the solution was poured into a volumetric flask just about to the 1dm3 line and then it was left there to cool to the same temperature as the room before filling precisely to the 1dm3 line with distilled water. The molar mass of CuSO4.5H20 was 249.5 so that means 249.5g of copper sulphate was needed to dissolve, in order to make a standard solution, into 1dm3of distilled water. Following this, a linear dilution of the CuSO4.5H2O was made in order to be used to make a calibration curve after using the colorimeter to write down the absorbance of each sample. A linear dilution is diluted with distilled water in order for it to make the concentration weaker and weaker. For this investigation, the dilutions made ranged from 0.01 to 0.1 M/l . It was essential to only make up 10cm3

The purpose of the experiment is to cycle solid copper through a series of five reactions. At different stages of the cycle, copper was present in different forms. First reaction involves reaction between the copper and nitric acid, and copper changed from elemental state to an aqueous. The second reaction converted the aqueous Cu2+ into the solid copper (2) hydroxide. In the third reaction Cu(OH)2 decomposed into copper 2 oxide and water when heated. When solid CuO reacted with sulfuric acid, the copper returned to solution as an ion (Cu2+). The cycle of reactions was completed with the reaction where elemental copper was regenerated by Zn and Cu

The mole is a convenient unit for analyzing chemical reactions. Avogadro’s number is equal to the mole. The mass of a mole of any compound or element is the mass in grams that corresponds to the molecular formula, also known as the atomic mass. In this experiment, you will observe the reaction of iron nails with a solution of copper (II) chloride and determine the number of moles involved in the reaction. You will determine the number of moles of copper produced in the reaction of iron and copper (II) chloride, determine the number of moles of iron used up in the reaction of iron and copper (II) chloride, determine the ratio of moles of iron to moles of copper, and determine the number of atoms and formula units involved in

The Empirical Formula is a formula that shows elements in a compound. The molecular formula gives the amount of atoms that each element has in a compound. These formulas were used to calculate and find elements that were given prior to the crash. The formulas also helped our team find out which passengers had each of the possible materials on the flight.

The purpose of this lab was to determine the limiting reactant in a reaction between copper sulfate and iron. Using the reaction between copper sulfate and iron, the reaction was observed to see the reaction and transformation of matter. The copper sulfate was placed into a beaker, as the excess reactant, then iron filings added until the heated solution was completely reacted. This reaction created an excess of leftover. The law of conservation of mass can be observed in this reaction, and using the data found, the percent yield calculated.

Oxidation involves the gain of electrons of hydrogen or the loss of oxygen or decrease in oxidation state. If zinc completely reacts with HCL, then the theoretical yield of copper should be equivalent to the actual yield.

The purpose of this experiment is to distinguish the relationships between reactants and products, in addition to expanding on concepts such as single displacement reactions, mole ratio values, moles to mass, theoretical yields, limiting reactants, excess, stoichiometric relationships and percentage errors.

Before the synthesis of the Copper Iodine Compound, the identities provided (CuNO3)2 and Nal weighed 1.65 g and 4.7 g, respectively. After being weighed, the (CuNO3)2 exhibited a blue color, while the Nal, through observation, was a white color. However, when both identities were combined, the product turned into a brown and red rocky material. Once 20 mL of deionized water was added, the product quickly turned pale pink paste. After the solution was repeatedly washed with a total of an additional 100 mL of deionized water, the product was powdery and pink with small grains, and was left to air-dry. Once the product was air dried, it was observed to be a pale pink color, while the filter paper was stiff as the product was hard and dry. Therefore, the solid was scraped off onto a recrystallizing dish. However, the mass of an empty recrystallizing dish needed to be recorded in order to compare how much of the synthesized copper iodide was obtained. Within this case, the empty recrystallizing dish used weighed 32.01 g, the product on the empty dish weighed 1.03 g, having a total weight of 33.04 g.

The Copper Cycle is a popular experiment used to determine if an element, in this instance, copper, reverts to its elemental form after a chain of reactions. This experiment is very dangerous because of the reactions between the strong acids and bases. In this experiment I performed a series of reactions starting with copper metal and nitric acid to form copper (II) nitrate. Then I reacted copper and several other solutions such as, sodium hydroxide, sulfuric acid, ammonium hydroxide, and hydrochloric acid to form precipitates. In conclusion my percent recovery

Purpose: The purpose of this experiment was to observe the many physical and chemical properties of copper as it undergoes a series of chemical reactions. Throughout this process, one would also need to acknowledge that even though the law of conservation of matter/mass suggests that one should expect to recover the same amount of copper as one started with, inevitable sources of error alter the results and produce different outcomes. The possible sources of error that led to a gain or loss in copper are demonstrated in the calculation of percent yield (percent yield= (actual yield/theoretical yield) x 100.

The lab performed required the use of quantitative and analytical analysis along with limiting reagent analysis. The reaction of Copper (II) Sulfate, CuSO4, mass of 7.0015g with 2.0095g Fe or iron powder produced a solid precipitate of copper while the solution remained the blue color. Through this the appropriate reaction had to be determined out of the two possibilities. Through the use of a vacuum filtration system the mass of Cu was found to be 2.1726g which meant that through limiting reagent analysis Fe was determined to be the limiting reagent and the chemical reaction was determined to be as following:-