Equilibrium Constant Of Fsn2 Solution Lab Report

The concentrations and absorbances of the red and blue dyes were used to find the concentration of the purple dyes. From the graph of the blue dye, the linear equation for absorbance was y = mx + b. From that formula came the equation y = 7.915 x 104 (x) + 0.02489, where y represents absorbance, m is slope, x is concentration/molarity, and b is the constant/y-intercept. The same set up was performed for the red dye, but the equation produced was y = 1.045 x 104 (x) +.001298. The equations found when graphing absorbance vs. concentration were used to find the concentration of the purple dyes. The absorbance for purple dye 3 on the red wavelength of 470 nm equaled 0.149 and 0.818 for the blue wavelength of 635 nm. For purple dye 1

From this graph and chart we can see that the higher the concentration the higher the absorbance, all the different concentrations were tested at the same wavelength (625nm). Also we can determine our unknown substances concentration by using the absorbance we got for it. The red dot on the graph followed by the line towards the horizontal axis indicates that the concentration of fast green was 34% or 5.1x10-3.

After this, the solution was poured into a volumetric flask just about to the 1dm3 line and then it was left there to cool to the same temperature as the room before filling precisely to the 1dm3 line with distilled water. The molar mass of CuSO4.5H20 was 249.5 so that means 249.5g of copper sulphate was needed to dissolve, in order to make a standard solution, into 1dm3of distilled water. Following this, a linear dilution of the CuSO4.5H2O was made in order to be used to make a calibration curve after using the colorimeter to write down the absorbance of each sample. A linear dilution is diluted with distilled water in order for it to make the concentration weaker and weaker. For this investigation, the dilutions made ranged from 0.01 to 0.1 M/l . It was essential to only make up 10cm3

The same solution of 0.5 ml BSA was then added from test tube 1 to the test tube 2 after being properly mixed, and from test tube 2 the solution was being added to test tube 3, and so forth all the way up to test tube 5, with the same exact procedure. From the last tube, we then disposed the 0.5 ml solution. After above procedures, we now labeled another test tube “blank”; 0.5 ml blank distilled water was purred into the tube with the serial dilution of 1:10. We also had a tube C labeled “unknown” with the same 0.5 ml of solution. And after adding 5ml of Coomassie Blue to each tube (1-5) and to the blank, the result of absorbance was read at 595 nm.

For this experiment, the amounts of Red 40 and Blue 1 were quantified in six different Kool-Aid samples through the use of a spectrophotometer. This was completing by performing serial dilutions on both dyes, Red 40 and Blue 1, and then creating calibration curves for each of the six samples. The absorbance and maximum wavelength values were obtained from the spectrophotometer for each individual drink sample. Beer’s Law was used to discover the concentration of

Scientists use an instrument called a spectrometer to quantitatively determine the amount of light absorbed by a solution. The primary inner parts of a typical spectrometer are described below. The spectrometer has a light source that emits white light containing a vast mixture of different wavelengths of electromagnetic radiation. The wavelength of interest is then selected using a monochromator (“mono” meaning one and “chromate” meaning color) and an additional exit slit. The separation of white light into different colors (wavelengths) is known as diffraction. The selected light then reaches the sample and depending on how the light interacts with the chemical compound of interest, some of the light is absorbed and some passes straight through. By comparing the amount of light entering the sample (P0) with the amount of light reaching the detector (P), the spectrometer is able to tell how much light is absorbed by the sample.

An experiment was done to determine the concentration of Allura Red in a commercially available beverage, Gatorade. This was done by using the colorimeter, the absorbance of five Allura Red solutions were measured. The graph obtained demonstrated a linear relationship and the equation obtained yielded a concentration of 1.9910-6M.

The Beers Law calibration experiment used many concentrations of crystal violet solutions. Each of these solutions were test and analyzed in order to determine the absorbance of each concentration The results were than graphed and produced a slope of 1.00E05 with an intercept of -2.21E-02.

The dark, navy blue colored graph represented the absorbance curve for the S1 sample. The red colored graph represented the absorbance curve for the S2 sample. The green colored graph represented the absorbance curve for the P1 sample. The purple colored graph represented the absorbance curve for the P2 sample. The gaps between the P2 curve was due to the oversaturation that led to the inconclusive spectrophotometer readings. The blue colored graph represented the absorbance curve for the P1 low salt sample. The orange colored graph represented the absorbance curve for the P2 low salt sample. The light blue colored graph represented the absorbance curve for the P1 medium salt sample. The light pink colored graph represented the absorbance curve for the P2 medium salt sample. The light green colored graph represented the absorbance curve for the P1 high salt sample. The light purple colored graph represented the absorbance curve for the P2 high salt

A spectrophotometer is an instrument which measures the amount of light of a specified wavelength which passes through a medium. This instrument is usually used for the measurement of reflectance of solutions. Light is separate into different wavelengths and is being passed through the sample solution. The sample solution will have its own wavelength and will absorb a certain amount of light. The higher the molecular concentration, the higher the absorbance value.

In this experiment, two reactions were run to determine the molar absorptivity and the equilibrium constant of FeSCN2+. The main principles used in this lab are equilibrium, LeChatlier’s Principle, Beer’s Law and Spectrocopy. The first reaction was run to completion using LeChatier’s Principle and the second reaction was run to equilibrium. A spectrophotometer was used to measure absorbances. Using a graph of absorbance versus concentration of FeSCN2+ was used to determine that the molar absorptivity constant was 3670. Beer’s Law was used to determine that the average equilibrium constant was 33.1793.

Incorporation of assay controls included setting up a spectrophotomer and running the chart recorder with a full-scale deflection before the start of the assay. The set recorder had a corresponding value of 1 for the change in the absorbance. Therefore, prior testing was done to observe whether a change occurred in the readings. This helped to indicate that the results were valid, as they could have been affected by a fault during the setting up of the spectrophotometer. On the other hand this was considered as one of the controls for the experiment. Nevertheless, a new cuvette had to be used for each assay.

The concentration of Nickel(II) Sulfate with a mystery concentration is 0.216M. To find this, the equation y=1.465x-0.022 was used, where y is the molarity(M) of the solution and x is the absorbance. The relationship between the absorbance and concentration is direct because as the absorbance goes up so does the concentration. The concentration was found by first taking a solution with a known concentration and finding the absorbance of it when strategically mixed with water (in mL) to have a variety of known concentrations. With the variety of solutions made with the same solute, the absorbance was found using red light, because it’s the opposite of green, in a colorimeter. The data was then put in a graph to find the relationship. Then, using

8) Steps 1 - 8 were repeated using the wavelengths of 360 nm to 900

concentration, record the absorbance readings at a fixed wavelength, and plot the absorbance vs. concentration data. The wavelength of 520 nm was selected for experiment Part