Essay On Acid-Base Extraction

The objective of this experiment is to separate a 50:50 mixture of benzoic acid and benzil by using macroscale extraction. In the experiment, organic solvent diethyl ether is used. After adding 1.0 gram of the 50:50 mixture of benzoic acid and benzil to a 25ml Erlenmeyer flask, diethyl ether was added to the flask to dissolve the mixture. Benzoic acid and benzil dissolve in diethyl ether. Once the mixture dissolved in

This experiment combined all the knowledge of the previous labs performed throughout the semester. An unknown mixture containing an organic acid or base and an organic neutral compound in nearly equal amounts needs to be separated to its separate components. An understanding of solubility, extraction, crystallization and vacuum filtration is necessary in order to

In the first acid extraction of benzocaine, the compound was dissolved in the organic solvent of dichloromethane. When the mixture was shaken with HCl, benzocaine’s amine group gained a proton and became more soluble in water than dichloromethane. This allowed the newly formed hydrochloric salt to migrate to the aqueous layer. However, the addition of NaOH to the acidic aqueous layer regenerated benzocaine by deprotonation, making it insoluble in the aqueous layer. The precipitation of an ionic salt was therefore recovered by vacuum filtration and had a tested melting point range of 85.1C-87.4C compared to 88C-90C, the literature melting point of benzocaine. The similarity in melting point ranges, but low percent yield of 30.37% proves that the extract was somewhat successful. Lower yields may be the result of spillage performed in the lab. In the second basic extraction, the organic layer now included benzoic acid and benzamide. When treated with NaOH to deprotonate benzoic acid, the newly formed sodium benzoate transitioned to the aqueous layer as a sodium salt. Benzoic acid is regenerated once again after the addition of HCl and became insoluble in the aqueous layer after protonation. Its precipitation was then filtered out for a 65.87% recovery. Compared to its literature melting point of 122.41C, the resulting 120.9C-123.5C melting range of the sample also supports the accuracy of the separation due to its similarities and high percent yield. In conclusion, the usage of base and acid liquid extraction was mostly successful in this experiment because it was able to efficiently and properly isolate the impure mixture into two separate components of benzocaine and benzoic acid. By performing the techniques of extraction and vacuum filtration, the similarities between literature and tested

Me and my lab partner, obtained a mixture of a un known proportion from the instructor and then flow the guide line in our lab manual to separate the mixture by applying the separation method motioned in our lab manual pages 33-40 . In this experiment, the separation methods were decantation,

There are millions of different organic compounds. Most of them are found in mixtures and in order to achieve a pure form they need to be separated, isolated, and purified. However, there are endless numbers of possible mixtures, which make it impossible to have a pre-designed procedure for every mixture. So chemists often have to make their own procedures. The purpose of this experiment was to prepare the student to the real world by them designing their own procedure which will help them understand the techniques of separation and purification better. The goal was to extract two of the components of the

The objective of this extraction experiment was to achieve a comprehensive understanding, as well as master the practice, of the technique of separating various individual components of a compound.

The problem that was trying to be solved in this study deals with analyzing unknown solutions. In this particular case, a chemical company has several unknown solutions and to correctly dispose of them they need to know their properties. To figure out the properties several qualitative tests were performed throughout the study (Cooper 2012).

The crude product was washed by taking the reaction product in the separatory funnel and adding 23 mL of deionized H2O. The mixture was shaken and allowed to settle until layers were observable. The top layer was the desired product and approximately 25 mL of aqueous layer was extracted from the separatory funnel. Next, 25 mL of 5% NaHCO3 was added to the separatory funnel in order to neutralize the acid. This mixture was swirled, plugged with the stopper and inverted. Built-up gas was released by turning the stopcock to its opened and closed positions, releasing CO2 by-product. This was done four times in one minute intervals. The solution was allowed to settle until layers were observable. The bottom layer that contained salt, base and water was extracted from the separatory funnel. The crude product was washed again as mentioned previously.

In this experiment, an acid-base extraction was done to separate a mixture of an unknown acid and fluorene, a neutral compound. The possible unknown acids were 2-chlorobenzoic acid, 3-chlorobenzoic acid, and 3-methylbenzoic acid. The purification of the isolated unknown acid was performed by recrystallization and its identity was established by analyzing the melting point range of the pure product and comparing it to the provided standards. In addition, a mixed melting point experimentation enhanced the fidelity of the unknown's

Experiment 4A: Determination of a Partition Coefficient for Benzoic Acid in Methylene Chloride and Water, and Experiment 4B: Solvent Extraction I: Acid-Base Extraction Using the System Benzoic Acid, Methylene Chloride, and Sodium Bicarbonate Solution

As the acid was being added, the mixture was being stirred over a stir plate. Once completed, the reaction mixture was poured from the round bottom flask into a 500 mL separatory funnel and its top (organic) layer was extracted into another beaker. The bottom (aqueous) layer was placed back into the funnel and extracted twice with 50.0 mL of ethyl ether each. The newly extracted layers were combined and dried over magnesium sulfate (MgSO4). The dried solution was the decanted into a beaker to remove the MgSO4 salts and the product solution was collected via Buchner vacuum filtration. The resulting product was transferred into an Erlenmeyer flask with an inverted beaker on top and stored in a drawer.

In the separating funnel, a heterogeneous mixture was formed: resulting in an organic layer (top) and a solvent layer (bottom). This effectively allowed the draining of the solvent, in order to isolate the organic layer, the impure ester (1-pentyl ethanoate)

In this experiment were used three separation techniques: extraction, sublimation and recrystallization. During the first method, 0.70 g sample of salicylic acid-naphthalene mixture was dissolved in 10 ml of diethyl ether. The solution was placed in a separatory funnel and 10 ml of saturated aqueous sodium bicarbonate solution was added to it. After the initial gas was

The purpose of this lab is to find out how components of a mixture can be separated and analyzed.

Six concrete blocks with the curing of 28 days were used to study the effects of acids and bases. Three blocks consist of sand and cement (Mortar mix) and the other three consist of sand, cement and aggregate (Pea gravel mix).