Experiment to investigate factors affecting the rate of reaction between magnesium ribbon and hydrochloric acid

2. Obtained a 2-3 cm strip of magnesium metal ribbon and coiled it loosely into a small ball. Added the magnesium metal to the acid in the test tube.

During the immersion of the magnesium metal in the hydrochloric acid solution, white bubbles could be seen escaping the surface of the metal as gas was produced during the reaction. Depending on the temperature of the hydrochloric acid and the overall molar concentration, the rate of reaction differed but the same signs were shown. During the reaction between the magnesium metal and higher concentrations of hydrochloric acid, it was observed that the test tube grew quite warm to the touch. As the immersed magnesium strip sank down, it appeared coated in a layer of white bubbles that fizzed like a carbonated drink. In the lower concentrations of hydrochloric acid, the strip spent some time floating at the surface of the solution in the test tube, later sinking down to the bottom as the

When the tip of the rod touched the pH paper, the color of the pH paper became blue.

always give out or take in energy most of the time this is heat energy

Title: The Effect Temperature of Sodium Thiosulfate Has On The Rate of Reaction with Hydrochloric Acid

The purpose of this lab was to test the law of definite proportions for the synthesis reaction of combusting magnesium. In this lab, the polished magnesium ribbon was placed in covered crucible and was heated in order for it to react with Oxygen presented in air and in water provided. The result showed that Magnesium oxide formed through chemical reaction was made up of 60.19% magnesium and 39.81% oxygen, which is approximate proportion of both particles in every Magnesium oxide compound. From this lab it can be concluded that the law of definite proportion stating that the elements in a pure compound combine in definite proportion to each other is factual.

    In this lab, a calorimeter was used to find the enthalpy of reaction for two reactions, the first was between magnesium and 1 molar hydrochloric acid, and the second was between magnesium oxide and 1 molar hydrochloric acid. After the enthalpy for both of these were found, Hess’ law was used to find the molar enthalpy of combustion of magnesium, using the enthalpies for the two previous reactions and the enthalpy of formation for water. The enthalpy of reaction for the magnesium + hydrochloric acid reaction was found to be -812.76 kJ. The enthalpy of reaction for the magnesium oxide + hydrochloric acid reaction was found to be -111.06 kJ. These two enthalpies and the enthalpy of formation for water were manipulated and added together using Hess’s law to get the molar enthalpy of combustion of magnesium. It was found that the molar enthalpy of combustion of magnesium was -987.5 kJ/mol. The accepted enthalpy was -601.6 kJ/mol, which means that there is a percent difference of 64%. This percent difference is very high which indicates that this type of experiment is very inefficient for finding the molar enthalpy of combustion of magnesium. Most likely, a there are many errors in this simple calorimeter experiment that make it inefficient for finding the molar enthalpy of combustion of magnesium.

Kinetics is the study of the rate of chemical processes. The kinetics of the reaction between crystal violet and NaOH was studied. In order to monitor crystal violet concentration as a function of time, a spectroscopic colorimeter was used. What is the rate law for decolorization of crystal violet? In order to figure this out, the rate of the reaction of crystal violet and sodium hydroxide must be found. In this experiment, the initial goals were to determine the overall rate law for the rate of decolorization of crystal violet in basic solutions as a function of time and to determine the rate law for the reaction including the actual value of k; Rate = k[A]x[B]y. The rate of a reaction was expected to depend on the concentrations

I could use a gas syringe to collect the gas that will evolve from my

About 80 mL of HCl was obtained and mixed with phenolphthalein. Using a LabQuest unit and Gas Pressure Sensor kit, the HCl mixture was added to the flask with the magnesium ribbon and allowed to react. When reaction was complete, the change of temperature and gas was recorded. This procedure was repeated for different masses of magnesium ribbon (masses found on page 89 of the lab manual). After the completed procedure, moles of H₂ produced in each trial were calculated. (The actual procedure can be found on pages 87-89 of the lab manual)

| After hydrochloric acid is added the mg reacts violently with bubbles and heat. Left over is a clear residue.

Experiment 2 focused on finding the enthalpy of solution of magnesium chloride. Testing the enthalpy of solution started with measuring out 10 mL of deionized water in a graduated cylinder for three separate trials, each trial having a different mass of magnesium chloride. The water was then poured into a well of a Styrofoam calorimeter then the initial temperature of water was taken using a temperature probe and the LoggerPro programming. A measured amount of magnesium chloride was placed in the same well as the water in the calorimeter,

Magnesium will react with hydrochloric acid, because it is higher in the reactivity series than hydrogen. The magnesium displaces the hydrogen in the acid, so it forms magnesium chloride and hydrogen gas.

It is expected that the concentration of hydrochloric acid will increase the rate of the reaction between magnesium ribbon and hydrochloric acid. By increasing the concentration of

Equation of magnesium and hydrochloric acid: 2 HCl+ + Mg [IMAGE]Mg2+ + H2 Measuring rates of reaction In this investigation there are two experiments that can be used to test rates of reaction. Using a gas syringe As more gas is produced the plunger inside the syringe moves out of the syringe so the gas can be measured by marks on the syringes length.