Experiments

The objective of this lab was to create a ketone through an oxidation reaction using a using a secondary alcohol and oxidizing agent in order to use that ketone in a reduction reaction with a specific reducing agent to determine the affect of that reducing agent on the diastereoselectivity of the product. In the first part of this experiment, 4-tert-butylcyclohexanol was reacted with NaOCl, an oxidizing agent, and acetic acid to form 4-tert-butylcyclohexanone. In the second part of this experiment, 4-tert-butylcyclohexanone was reacted with a reducing agent, either NaBH4 in EtOH or Al(OiPr)3 in iPrOH, to form the product 4-tert-butylcyclohexanol. 1H NMR spectroscopy was used to determine the cis:trans ratio of the OH relative to the tert-butyl group in the product formed from the reduction reaction with each reducing agent. Thin-layer chromatography was used in both the oxidation and reduction steps to ensure that each reaction ran to completion.

Different procedures were used to isolate benzil from the ether layer and benzoic acid from the aqueous layers. To isolate benzil, anhydrous MgSO4 was added to the flask containing the ether layer solution. MgSO4 removes the remaining water in the ether layer solution. After making sure that enough amount of MgSO4 present in the solution, the ether solution was filtered by using gravity filtration. During filtration, MgSO4 was removed from the solution and the ether solution was collected in 25 ml flask. To separate benzil from the filtered ether solution, the beaker containing the ether solution was heated until the ether evaporated. After letting the beaker to cool to room temperature, the mass of the beaker with the benzil crystals was measured. From the combined mass of the beaker and the benzil crystals and from the predetermined mass of the beaker, the mass of the collected crystals was calculated to be 0.266 gram.

For this experiment, an organometallic reagent was used for the synthesis and isolation of benzoic acid. The Grignard reaction is the addition reaction of an organometallic reagent, which in this case was an organomagnesium reagent. An organometallic reagent is a carbon bonded to a metal. This reagent was combined with an electrophile, a carbonyl compound such as a ketone or aldehyde. Carbons are electrophilic when bound to a nonmetal thus the atoms are more electronegative than the carbon and metals are less electronegative than carbon.

In the Cannizaro reaction an aldehyde is simultaneously reduced into its primary alcohol form and also oxidized into it 's carboxylic acid form. The purpose of this experiment is to isolate, purify and identify compounds 1 and 2 which contain 4-chlorobenzaldehyde, methanol, and aqueous potassium hydroxide. Compounds 1 and 2 are purified by crystallization. . The purified product will be characterized by IR spectroscopy and melting point.

Abstract: One mixture of two unknown liquid compounds and one mixture of two unknown solid compounds were separated, isolated, purified, and characterized by boiling point. Two liquid unknowns were separated, isolated, and purified via simple distillation. Then, the process of an acid-base extraction and washing were used to separate two unknown compounds into two crude compounds: an organic acid and a neutral organic compound. Each crude compound was purified by recrystallization, resulting in a carboxylic acid (RCO2H) and a pure organic compound (RZ). The resulting mass of the pure carboxylic acid was 1.688g with a percent recovery of 31.80%, the boiling range was 244-245 °C, and its density was 2.0879g/mL. The resulting mass of the pure organic solid was 2.4902g with a percent recovery of 46.91%, the boiling range was 52.0-53.4°C, and its density was 1.5956 g/mL.

Three grams of a mixture containing Benzoic Acid and Naphthalene was obtained and placed in 100 ml beaker and added 30 ml of ethyl acetate for dissolving the mixture. A small amount (1-2 drops) of this mixture was separated into a test tube. This test tube was covered and labelled as “M” (mixture). This was set to the side and used the following week for the second part of lab. The content in the beaker was then transferred into separatory funnel. 10 ml of 1 M NaOH added to the content and placed the stopper in the funnel. In the hood separatory funnel was gently shaken for approximately one minute and vent the air out for five seconds. We repeated the same process in the same manner one more time by adding 10ml of 1M NaOH.

After 10 minutes the reaction liquid was separated from the solid using a vacuum filtration system and toluene. The product was stored and dried until week 2 of the experiment. The product was weighed to be 0.31 g. Percent yield was calculated to be 38.75%. IR spectra data was conducted for the two starting materials and of the product. Melting point determination was performed on the product and proton NMR spectrum was given. The IR spectrum revealed peaks at 1720 cm-1, which indicated the presence of a lactone group, and 1730 cm-1, representing a functional group of a carboxylic acid (C=O), and 3300cm-1, indicating the presence of an alcohol group (O-H). All three peaks correspond with the desired product. A second TLC using the same mobile and stationary phase as the first was performed and revealed Rf Values of 0.17 and 0.43for the product. The first value was unique to the product indicating that the Diels-Alder reaction was successful. The other Rf value of 0.43 matched that of maleic anhydride indicating some

In this experiment, 1,2-cyclohexene was taken and made it 1,2-cyclohexanediol in two separate reactions. Two products were formed in each respective reaction: cis-1, 2-cyclohexene and trans-1, 2-cyclohexanediol. To figure out which product was formed in each reaction, TLC was used to test the stereochemistry from the products compared to the actual compounds. Each retention factor was compared to the actual product retention factors to see if the reactions had been done properly.

In this experiment, the main objective was to synthesize a ketone from borneol via an oxidation reaction and secondly, to produce a secondary alcohol from camphor via a reduction reaction. Therefore, the hypothesis of this lab is that camphor will be produced in the oxidation reaction and isoborneol will be the product of the reduction reaction because of steric hindrance. For the oxidation step, a reflux will be done and then a microscale reflux for the reduction step. The products will be confirmed using Infrared spectroscopy, the chromic acid test, 2,4-DNP test and 13C NMR spectroscopy. The results of this

Benzyltriphenylphosphonium chloride (0.201g) and 9-anthraldehyde (0.116g) were weighed and added to a short-neck round-bottomed flask (5ml). Dichloromethane (2ml) was measured using a measuring cylinder and added to the

The reaction took place in a conical vial and .2mL of each of the reactant samples were added to it along with some 95% ethanol. Two drops of NaOH were added shortly after and stirred at room temperature for fifteen minutes. The vial was cooled in and ice bath and crystallized. Vacuum filtration was performed to filter the crude product. The crude product was recrystallized using methanol and filtered again. We made one change to the procedure and instead of using .7mL of ethanol we

Varying concentrations of chemically-manufactured acetone solution were used in this experiment, which also acted as the control for the detection of acetone. Measurement was made using the UV-Vis spectrophotometer.

After the initial mixture has refluxed, 9.11 grams of benzophenone was dissolved in 100 mL of anhydrous ether in a beaker and was then transferred into the separatory on the reflux apparatus. This solution was then added to the Grignard reagent at a drop wise rate while stirring. After the benzophenone was added, the mixture was then refluxed for 15 minutes on a heating mantle.

One milliliter of 6.00-M phosphoric acid was placed into a 125-mL Erlenmeyer flask using a volumetric pipette. Using a slightly larger pipette, six milliliters of 3.00-M sodium hydroxide was transferred into a 50-mL beaker. Then a disposable pipette was used to slowly mix the sodium hydroxide into the phosphoric acid while the solution was swirled around. Then both the beaker and flask were rinsed with 2-mL of deionized water and set aside. A clean and dry evaporating dish was weighed with watch glass on a scale. Then the solution was poured into the dish and the watch glass was placed on top. The solution was then heated with a Bunsen burner to allow for the water to boil off to reveal a dry white solid. After the dish cooled to room temperature it was once again weighed and the new mass was recorded.

The purpose of refluxing the reaction was to break the bond in the p-acetaminophen and acetic anhydride at the same time the condenser prevent some molecule to escape though evaporation by capturing it and return it into the reaction vessel. The heat was necessary to break bond in P-acetaminophen and in acetic anhydride by increasing the rate of reaction and bringing molecules closer to the activation energy. Product isolation was performed by cooling the solution, and filtered it to isolate the crystals of the products by using Hirsch funnel. This crude product was then purified through recrystallization technique and by using Craig tube. The final process was to identify the product by using dig melt machine to find out the melting point