Separation Of Benzoic Acid And Alkaline Lab Report

The trap was cooled in a beaker of ice water to recover the dichloromethane. To increase the evaporation rate, heat and swirl the mixture over a heat bath. When a solid remains or no more solvent evaporates, the unknown was left to dry to constant mass. After the unknown was dry, it was boiled with enough water (found by calculations) to dissolve it completely and was cooled to room temperature.

3. Turned off the laboratory burner and observed the properties of the product in the evaporating dish.

There are various techniques to separate a mixture of compounds from each other. One of the commonly used way to isolate compounds from a mixture of two compounds is called extraction. This method of extracting two compounds from each other relies on the different solubility of the compounds in two different solvents.

22. Pushing the stopper to make sure it is firmly attached to the mouth of the syringe, press the plunger inward.

In the first acid extraction of benzocaine, the compound was dissolved in the organic solvent of dichloromethane. When the mixture was shaken with HCl, benzocaine’s amine group gained a proton and became more soluble in water than dichloromethane. This allowed the newly formed hydrochloric salt to migrate to the aqueous layer. However, the addition of NaOH to the acidic aqueous layer regenerated benzocaine by deprotonation, making it insoluble in the aqueous layer. The precipitation of an ionic salt was therefore recovered by vacuum filtration and had a tested melting point range of 85.1C-87.4C compared to 88C-90C, the literature melting point of benzocaine. The similarity in melting point ranges, but low percent yield of 30.37% proves that the extract was somewhat successful. Lower yields may be the result of spillage performed in the lab. In the second basic extraction, the organic layer now included benzoic acid and benzamide. When treated with NaOH to deprotonate benzoic acid, the newly formed sodium benzoate transitioned to the aqueous layer as a sodium salt. Benzoic acid is regenerated once again after the addition of HCl and became insoluble in the aqueous layer after protonation. Its precipitation was then filtered out for a 65.87% recovery. Compared to its literature melting point of 122.41C, the resulting 120.9C-123.5C melting range of the sample also supports the accuracy of the separation due to its similarities and high percent yield. In conclusion, the usage of base and acid liquid extraction was mostly successful in this experiment because it was able to efficiently and properly isolate the impure mixture into two separate components of benzocaine and benzoic acid. By performing the techniques of extraction and vacuum filtration, the similarities between literature and tested

14 mL of 9 M H2SO4 was added to the separatory funnel and the mixture was shaken. The layers were given a small amount of time to separate. The remaining n-butyl alcohol was extracted by the H2SO4 solution therefore, there was only one organic top layer. The lower aqueous layer was drained and discarded. 14 mL of H2O was added to the separatory funnel. A stopper was placed on the separatory funnel and it was shaken while being vented occasionally. The layers separated and the lower layer which contained the n-butyl bromide was drained into a smaller beaker. The aqueous layer was then discarded after ensuring that the correct layer had been saved by completing the "water drop test" (adding a drop of water to the drained liquid and if the water dissolves, it confirms that it is an aqueous layer). The alkyl halide was then returned to the separatory funnel. 14 mL of saturated aqeous sodium bicarbonate was added a little at a time while the separatory funnel was being swirled. A stopper was placed on the funnel and it was shaken for 1 minute while being vented frequently to relieve any pressure that was being produced. The lower alkyl halide layer was drained into a dry Erlenmeyer flask and 1.0 g of anhydrous calcium chloride was added to dry the solution. A stopper was placed on the Erlenmeyer flask and the contents were swirled until the liquid was clear. For the distillation

There are millions of different organic compounds. Most of them are found in mixtures and in order to achieve a pure form they need to be separated, isolated, and purified. However, there are endless numbers of possible mixtures, which make it impossible to have a pre-designed procedure for every mixture. So chemists often have to make their own procedures. The purpose of this experiment was to prepare the student to the real world by them designing their own procedure which will help them understand the techniques of separation and purification better. The goal was to extract two of the components of the

The objective of this extraction experiment was to achieve a comprehensive understanding, as well as master the practice, of the technique of separating various individual components of a compound.

In order to isolate benzoic acid, benzocaine and 9-fluorenone, each component needed to be separated from one another. All three compounds began together in one culture tube, dissolved in methylene chloride and formed into a homogenous mixture. In this culture tube, two milliliters of aqueous three molar hydrochloric acid was added, which immediately formed two layers, the top acidic aqueous layer was clear in color and contained benzocaine, and the bottom organic formed was yellow and contained benzoic acid and 9-fluorenone. Benzocaine’s amino group is protonated by the aqueous layer hydronium. This protonation forms the conjugate acid of benzocaine, benzocaine hydrochloride. Thus, the conjugate acid, benzocaine hydrochloride is a salt in which is soluble in water and furthermore can be isolated from the organic mixture. When testing out the pH levels in benzocaine, the pH test strip was dark blue in color, indicating a pH level of around 5 to 7. When isolating benzoic acid, two milliliters of aqueous three molar sodium hydroxide was added, which deprotonates the carboxylic group in benzoic acid, forming its conjugate base, sodium benzoate. As with benzocaine hydrochloride, sodium benzoate is a water soluble ionic salt in the aqueous layer that can then be separated from the bottom organic layer containing the 9-fluorenone. The pH test strip was a vibrant red for benzoic acid, indicating a pH of 2. Now the 9-fluorenone is left, deionized water is added to remove any excess

Three grams of a mixture containing Benzoic Acid and Naphthalene was obtained and placed in 100 ml beaker and added 30 ml of ethyl acetate for dissolving the mixture. A small amount (1-2 drops) of this mixture was separated into a test tube. This test tube was covered and labelled as “M” (mixture). This was set to the side and used the following week for the second part of lab. The content in the beaker was then transferred into separatory funnel. 10 ml of 1 M NaOH added to the content and placed the stopper in the funnel. In the hood separatory funnel was gently shaken for approximately one minute and vent the air out for five seconds. We repeated the same process in the same manner one more time by adding 10ml of 1M NaOH.

The wet, crude product was placed into the 50 mL Erlenmeyer flask. Small amounts of CaCl2 were added to dry the solution. The flask was sealed and the mixture was swirled and left to settle. Once

Objective: The objective of this experiment is to use acid-base extraction techniques to separate a mixture of organic compounds based on acidity and/or basicity. After the three compounds are separated we will recover them into their salt forms and then purify them by recrystallization and identify them by their melting points.

Experiment 4A: Determination of a Partition Coefficient for Benzoic Acid in Methylene Chloride and Water, and Experiment 4B: Solvent Extraction I: Acid-Base Extraction Using the System Benzoic Acid, Methylene Chloride, and Sodium Bicarbonate Solution

3. A few drops of 6 M acetic acid were added until it became basic.

The purpose of this experiment was to use solvent extraction techniques in order to separate a mixture consisting of a carboxylic acid (p-toulic acid), a phenol (p-tert-butylphenol), and a neutral compound (acetanilide). Extraction is the process of selectively dissolving one or more of the compounds of a mixture into an appropriate solvent, the solution that contains these dissolved compounds is called an extract (Manion, 2004).