Fractional Distillation Lab

I. LIQUID - Identification of an Unknown Liquid: Using the physical properties of Solubility, Density, and Boiling Point.

14 mL of 9 M H2SO4 was added to the separatory funnel and the mixture was shaken. The layers were given a small amount of time to separate. The remaining n-butyl alcohol was extracted by the H2SO4 solution therefore, there was only one organic top layer. The lower aqueous layer was drained and discarded. 14 mL of H2O was added to the separatory funnel. A stopper was placed on the separatory funnel and it was shaken while being vented occasionally. The layers separated and the lower layer which contained the n-butyl bromide was drained into a smaller beaker. The aqueous layer was then discarded after ensuring that the correct layer had been saved by completing the "water drop test" (adding a drop of water to the drained liquid and if the water dissolves, it confirms that it is an aqueous layer). The alkyl halide was then returned to the separatory funnel. 14 mL of saturated aqeous sodium bicarbonate was added a little at a time while the separatory funnel was being swirled. A stopper was placed on the funnel and it was shaken for 1 minute while being vented frequently to relieve any pressure that was being produced. The lower alkyl halide layer was drained into a dry Erlenmeyer flask and 1.0 g of anhydrous calcium chloride was added to dry the solution. A stopper was placed on the Erlenmeyer flask and the contents were swirled until the liquid was clear. For the distillation

In this experiment, we used distillation to separate a mixture of cyclohexane and toluene. We used two types of distillation simple and fractional. The experiment was carried out by mixing the cyclohexane and toluene in a round bottom flask, and the mixture was heated to boiling (in sand bath) and vaporized. The vapor then condensed by the condenser where the water was running through to cool the vapor back to liquid. Since this was a mixture of two liquids, the temperature was continuously increasing throughout the process. The different boiling points of cyclohexane and toluene allows the separation to occur. Cyclohexane has a boiling point of 81 °C and toluene has a boiling point of 111 °C, since cyclohexane has a lower boiling point it

Abstract: One mixture of two unknown liquid compounds and one mixture of two unknown solid compounds were separated, isolated, purified, and characterized by boiling point. Two liquid unknowns were separated, isolated, and purified via simple distillation. Then, the process of an acid-base extraction and washing were used to separate two unknown compounds into two crude compounds: an organic acid and a neutral organic compound. Each crude compound was purified by recrystallization, resulting in a carboxylic acid (RCO2H) and a pure organic compound (RZ). The resulting mass of the pure carboxylic acid was 1.688g with a percent recovery of 31.80%, the boiling range was 244-245 °C, and its density was 2.0879g/mL. The resulting mass of the pure organic solid was 2.4902g with a percent recovery of 46.91%, the boiling range was 52.0-53.4°C, and its density was 1.5956 g/mL.

Method: Distillation is based on the fact that the matter can exist in three phases - - solid, liquid and gas. As the temperature of a pure substance is increased, it passes through these phases, making a transition at a specific temperature from solid to liquid (melting point--mp) and then at a higher temperature from liquid to gas (boiling point--bp). Distillation involves evaporating a liquid into a gas phase, then condensing the gas back into a liquid and collecting the liquid in a clean receiver. Substances that have a higher boiling point than the desired material will not distill at the

Objective: The main goal of this lab is to learn how separation of binary liquid mixtures is performed. Especially when the two liquids have boiling points varying by about 30° C. Hexane can be separated from toluene in this experiment because of the difference in their boiling points. Since toluene has a higher boiling point, it will left at the bottom while the hexane starts to boil out and collect in the Hickman still. GC measurements help us in determining how accurate our data is by making a graph of the amount of hexane and toluene in each fraction. Also this lab gives experience with semi-micro

In this experiment, distillations were done. This is a technique that utilizes the differing boiling points of two or more compounds in a mixture in order to separate the compounds from the mixture. The way fractional distillation works is that the initial mixture is boiled up to the point of the lower boiling point compound; this compound then evaporates. This compound is then

Simple distillation is a separation technique which can be used to separate and purify distillates from a liquid mixture which ideally contains one volatile and one non-volatile compound. If such ideal conditions are not possible—as is usually the case—then simple distillation can be applied as long as the liquid in question is composed of compounds that differ in volatility such that their boiling points differ by at least 40 to 50 degrees Celsius. Because

1.) Briefly explain the concept of steam distillation. What is the difference between a simple distillation and a steam distillation? When a mixture of two immiscible liquids are distilled it is referred to as codistillation. This process is referred to as steam distillation when one of the liquids is water. This distillation is used to separate organic liquids from natural products and reaction mixtures in which the final product results in high boiling residues such as tars, inorganic salts, and other relatively involatile components. It is useful in isolating volatile oils from various parts of plants and not useful in the final purification of a

Distillation is a method of separating two volatile chemicals on the basis of their differing boiling points. During this lab, students were given 30 mL of an unknown solution containing two colorless chemicals. Because the chemicals may have had a relatively close boiling point, we had to employ a fractional distillation over a simple distillation. By adding a fractionating column between the boiling flask and the condenser, we were able to separate the liquids more efficiently due to the fact that more volatile liquids tend to push towards the top of the fractionating column, thereby leaving the liquid with the lower boiling point towards the bottom. After obtaining the distillates, we utilized a gas chromatograph in order to analyze the volatile substances in the gas phase and determine their composition percentage of the initial solution. Overall, through this lab we were able to enhance our knowledge on the practical utilization of chemical theories, and thus also demonstrated technical fluency involving the equipment.

The boiling range of the 1-pentyl ethanoate distillate was approximately between 149-151°C. This was indicated by the formation of the distillate and when the mixture of the purified 1-pentyl ethanoate started to vigorously

The purpose of this experiment was to separate a two component mixture using fractional distillation. Distillation is a process of vaporization than condensation of a substance, used primarily to separate substances from a mixture when there are different boiling points. Fractional distillation is when the mixture has multiple substances with similar boiling points, and a fractional column is used to create multiple vaporization/condensation cycles. Fractional distillation is important when two or more substances need to be separated, but they have similar boiling points.

The purpose of this experiment is to identify an unknown substance by measuring the density and boiling point. I will be able to conclude which substance is my own from a list of known options stating what its real boiling point and density is.

Matter is what everything around us is made up of and chemistry is concerned with how this matter - more specifically how atoms - can interact, transform and produce different substances depending on their structure. These different structures and arrangements atoms take ultimately create solids, liquids and gases. In solids, the atoms are close together and therefore vibrate in fixed positions. In liquids, atoms are further apart, however, they still are rather close and slide over each other. And in gases, there is a large amount of space in between atoms and they are constantly moving around. Many different substances that these atoms form - whether solids, liquids or gases - can be incredibly useful, and as a result, different techniques

The purpose of distillation is to purify a liquid. Distillations are use to purify contaminates out of water to obtain clean pure water, as well as, to separate mixtures of liquids into their individual components; e.g. methanol and water.