Fractional Distillation Lab Report

Solid impurities and liquid impurities having quite different boiling points are most easily removed by distillation, but even liquids having similar boiling points can be separated. For easy separations, a "simple distillation" apparatus (Figure 1) will be used for the first part, but for more accurate separations, a "fractional distillation" apparatus (Figure 2) is necessary. In this lab we will be using both apparatuses. Unfortunately, each time a distillation is run, material is lost. Some evaporates into the air and some is left behind, stuck to the apparatus. That is why fractional distillation is the best apparatus to use. It is important to keep a careful record of the temperature at the beginning and end of every fraction you collect. Stop the distillation by removing the heat just before all the liquid in the distilling flask is completely gone. Watching the rate of temperature increase is important, allowing the temperature to increase too quickly can cause impurity. The distillation curves for our simple and fractional distillation clearly demonstrate that fractional distillation separates the two compounds more

Whereas for simple distillation, the compounds need to be around 80C apart in order for proper separation to occur. Thus, cyclohexane and toluene were not able to be properly separated since the boiling point for cyclohexane was 80.74C while the boiling point of toluene was 110.6C—there two boiling points are fairly close to one another. Thus, the mole fraction for cyclohexane and toluene were fairly low when compared to cyclohexane and

Method: Distillation is based on the fact that the matter can exist in three phases - - solid, liquid and gas. As the temperature of a pure substance is increased, it passes through these phases, making a transition at a specific temperature from solid to liquid (melting point--mp) and then at a higher temperature from liquid to gas (boiling point--bp). Distillation involves evaporating a liquid into a gas phase, then condensing the gas back into a liquid and collecting the liquid in a clean receiver. Substances that have a higher boiling point than the desired material will not distill at the

Objective: The main goal of this lab is to learn how separation of binary liquid mixtures is performed. Especially when the two liquids have boiling points varying by about 30° C. Hexane can be separated from toluene in this experiment because of the difference in their boiling points. Since toluene has a higher boiling point, it will left at the bottom while the hexane starts to boil out and collect in the Hickman still. GC measurements help us in determining how accurate our data is by making a graph of the amount of hexane and toluene in each fraction. Also this lab gives experience with semi-micro

In this experiment, distillations were done. This is a technique that utilizes the differing boiling points of two or more compounds in a mixture in order to separate the compounds from the mixture. The way fractional distillation works is that the initial mixture is boiled up to the point of the lower boiling point compound; this compound then evaporates. This compound is then

Simple distillation is more effective when the two components of a mixture have a difference in boiling point that is greater than 50°C. This large difference makes the need for theoretical plates non-existent since there is no need for multiple distillations per fraction. We can collect all necessary data from a simple distillation fraction using a gas chromatograph. The gas chromatograph vaporizes the injected sample and it begins to undergo partitioning. It is pushed into a small heated column that is coated in the liquid form of the sample. The longer the substance stays inside the column before passing over the heated wire, the longer the retention time is. The retention time is utilized to identify the substance, while the number of peaks shows how many substances are present, and the size of the peaks show how much percentage each substance occupies in a sample. The intrinsic properties of isopropyl acetate and toluene allow analysis of the provided data to become quite simple. Isopropyl acetate has a lower boiling point because it has a relatively low dipole moment and only one double bond. Thus, the intermolecular forces are relatively low in isopropyl acetate leading to a low boiling point. Toluene has a higher boiling point because the methyl group, attached to the benzene

In this lab, the molar mass of a volatile liquid is determined based on its physical properties in the vapor state. In order to calculate the molar mass, the mass, temperature, pressure, and volume is measured independently and then converted to the correct units. Sample C was obtained at the beginning of the experiment, which was later informed to be ethanol. Based on the calculations made, the molar mass of the volatile liquid was 95.9 g/mol. However, compared to the known value of 46.1 g of ethanol, the value measured had a 108% error. Unfortunately, this was a very big percent error and may have been caused by incorrectly measuring the volume of the gas. Using the ideal gas law, the molar mass of a volatile compound was calculated in order

Simple distillation is a separation technique which can be used to separate and purify distillates from a liquid mixture which ideally contains one volatile and one non-volatile compound. If such ideal conditions are not possible—as is usually the case—then simple distillation can be applied as long as the liquid in question is composed of compounds that differ in volatility such that their boiling points differ by at least 40 to 50 degrees Celsius. Because

This is different from fractional distillation because you would use this technique if there is a mixture of liquids with volatilities that cannot be separated easily. Also, because it is harder to separate this liquids another condenser has to be added to the distillation setup, this condenser has a metal sponge inside of it and tinfoil wrapped around the outside in order to increase surface area and ensures that the liquid heats enough to be able to reach the other condenser, this is attached to the round bottom flask that sits on the hot plate. For part A, the distillation can be described as a steady rounded incline, could be determined as a linear curve. Whereas in part B the distillation graph first starts as an almost straight line and then there is a quick almost S-like jump to a higher temperature and then continues at a slow

1.) Briefly explain the concept of steam distillation. What is the difference between a simple distillation and a steam distillation? When a mixture of two immiscible liquids are distilled it is referred to as codistillation. This process is referred to as steam distillation when one of the liquids is water. This distillation is used to separate organic liquids from natural products and reaction mixtures in which the final product results in high boiling residues such as tars, inorganic salts, and other relatively involatile components. It is useful in isolating volatile oils from various parts of plants and not useful in the final purification of a

Distillation is a method of separating two volatile chemicals on the basis of their differing boiling points. During this lab, students were given 30 mL of an unknown solution containing two colorless chemicals. Because the chemicals may have had a relatively close boiling point, we had to employ a fractional distillation over a simple distillation. By adding a fractionating column between the boiling flask and the condenser, we were able to separate the liquids more efficiently due to the fact that more volatile liquids tend to push towards the top of the fractionating column, thereby leaving the liquid with the lower boiling point towards the bottom. After obtaining the distillates, we utilized a gas chromatograph in order to analyze the volatile substances in the gas phase and determine their composition percentage of the initial solution. Overall, through this lab we were able to enhance our knowledge on the practical utilization of chemical theories, and thus also demonstrated technical fluency involving the equipment.

The boiling range of the 1-pentyl ethanoate distillate was approximately between 149-151°C. This was indicated by the formation of the distillate and when the mixture of the purified 1-pentyl ethanoate started to vigorously

The purpose of this experiment was to separate a two component mixture using fractional distillation. Distillation is a process of vaporization than condensation of a substance, used primarily to separate substances from a mixture when there are different boiling points. Fractional distillation is when the mixture has multiple substances with similar boiling points, and a fractional column is used to create multiple vaporization/condensation cycles. Fractional distillation is important when two or more substances need to be separated, but they have similar boiling points.

The first thing that comes to everyone’s mind when they hear home distiller or home distillery is a picture of that prohibition era man in his overalls distilling in the woods. This is not the case! Home Distilling is becoming more popular by the day. So what should you do if you want to begin distilling?

The main objective of the distillation lab was to identify the composition of an unknown binary solution. The only known component is that the boiling point of the two components were at least 40˚C apart in boiling points. Due to the difference in boiling points, fractional distillation would be an easy way to determine the identity of each component of the binary solution. In the experiment, 30mL of the unknown binary solution was ran through the fractional distillation apparatus. As the solution boiled, gas from the unknown solution ran through the column, which had a temperature gradient to allow rapid and repeated distillations, and one of the components were isolated. By recording the temperature and amount of