Grignard Reaction

Any amount of H2O present would react with and therefore ruin the Grignard reagent. The negative charge on the Grignard carbon would pop a proton off of water, and the resulting hydroxide would react with MgBr2. Since all of the water and moisture was removed, the reaction should run successfully. For this experiment’s reaction, bromobenzene is turned into phenylmagnesium bromide, a Grignard reagent. Then, the Grignard reagent is reacted with benzophenone to yield a molecule with a negative charge on the oxygen. This molecule is worked up and protonated to yield triphenylmethanol.

Melting Point Data Table Compound Aspirin Caffeine Salicylamide Actual MP (ºC) 93 - 98 260 - 262 96 - 102 Expected MP (ºC) 135 236 140 Percent Error (%) ~30% ~12% ~30%

The purpose of this experiment was to synthesize the Grignard reagent, phenyl magnesium bromide, and then use the manufactured Grignard reagent to synthesize the alcohol, triphenylmethanol, by reacting with benzophenone and protonation by H3O+. The triphenylmethanol was purified by recrystallization. The melting point, Infrared Spectroscopy, 13C NMR, and 1H NMR were used to characterize and confirm the recrystallized substance was triphenylmethanol.

A chemical reaction is when substances (reactants) change into other substances (products). The five general types of chemical reactions are synthesis (also known as direct combination), decomposition, single replacement (also known as single displacement), double replacement (also known as double displacement), and combustion. In this lab, the five general types of chemical reactions were conducted and observations were taken before, during, and after the reaction. Then the reactants and observations were used to determine the products to form a balanced chemical equation. The purpose of this lab was to learn and answer the question: How can observations be used to determine the identity of substances produced in a chemical reaction?

The sodium hydroxide acts to pull the hydrogen off the oxygen in the 2-methylphenol so that the oxygen has a negative charge and can attack the sodium chloroacetate. Again, using a 1:1 molar ratio, 0.34 g (2.9 mmol) of sodium chloroacetate (the good leaving group) was added to 1 ml of water and dissolved. Following dissolving all of the 2-methylphenol (to avoid the sodium hydroxide reacting concurrently with the sodium chloroacetate and 2-methylphenol) in the sodium hydroxide, the aqueous solution of sodium chloroacetate was transferred to the reaction flask. This mixture was then heated to reflux, using a medicine dropper affixed to the top of the flask as an alternative method to boil without

For the organic layer, we had a melting point range of 240-243°C. For the IR spectra, we did note the C-Cl bond although there was not an OH bond present.

0.1 gram of salicylic acid was weighed in a tray and was then added to a test tube containing 2.0 mL of Iron (III) chloride, which was measured using a 10 mL graduated cylinder, to test for phenols.

Purpose: The purpose of this experiment is to observe a variety of chemical reactions and to identify patterns in the conversion of reactants into products.

The Grignard reaction is an important synthetic process by which a new carbon to carbon bond is formed. Magnesium metal is first reacted with an organic halide forming the Grignard reagent. The Grignard reaction is the addition of an organomagnesium halide (Grignard reagent) to a ketone or aldehyde, to form a tertiary or secondary alcohol, respectively. For example, the reaction with formaldehyde leads to a primary alcohol. Grignard Reagents are also used in the following important reactions: The addition of an excess of a Grignard reagent to an ester or lactone gives a tertiary alcohol in which two alkyl groups are the same, and the addition of a

Discussion: As seen in the melting point determination, the average melting point range of the product was 172.2-185.3ºC. The melting points of the possible products are listed as 101ºC for o-methoxybenzoic acid, 110ºC for m- methoxybenzoic acid, and 185ºC for p- methoxybenzoic acid. As the melting point of the sample

After allowing the flask to cool to room temperature and cooling on ice, the product was collected and washed with 2-propanol (2ml) into a clean Hirsch funnel and was filtered using vacuum filtration. The triphenylphosphine oxide remained in the propanol solution, and the crystals were dried by drawing air through them. The mass, percentage yield and melting point of the product was obtained. The crystals were stored in a glass vial for next experiment.

The reaction took place in a conical vial and .2mL of each of the reactant samples were added to it along with some 95% ethanol. Two drops of NaOH were added shortly after and stirred at room temperature for fifteen minutes. The vial was cooled in and ice bath and crystallized. Vacuum filtration was performed to filter the crude product. The crude product was recrystallized using methanol and filtered again. We made one change to the procedure and instead of using .7mL of ethanol we

Through the use of the Grignard reaction, a carbon-carbon bond was formed, thereby resulting in the formation of triphenylmethanol from phenyl magnesium bromide and benzophenone. A recrystallization was performed to purify the Grignard product by dissolving the product in methanol. From here, a melting point range of 147.0 °C to 150.8 °C was obtained. The purified product yielded an IR spectrum with major peaks of 3471.82 cm-1, 3060.90 cm-1, 1597.38 cm-1, and 1489.64 cm-1, which helped to testify whether the identity of the product matched the expected triphenylmethanol. The identity of the product being correct was further confirmed by way of both proton and carbon-13 NMR spectra. This is due to the fact

The purpose of this lab was to synthesize triphenylmethanol from benzophenone and bromobenzene by the formation of a Grignard compound with the reagents bromobenzene and magnesium metal. The bromobenzene was first transformed into the Grignard compound and was then reacted with the benzophenone to make the final product. The mixture was then mixed with sulfuric acid and the organic layer was extracted via a separatory funnel. The mixture was then recrystallized from methanol and was allowed to dry and the percent yield, melting point, and the IR was obtained. The mass of the product obtained was 5.45 grams and the percentage yield was determined to be 41.95%. The melting point range obtained from the final product was 89-91°C

Melting range would be closely related to a mixed sample whose constituents are most identical. In other words, melting point will have a wide range and would be below 200°C and above 95°C.