Changing The Oil In A Car's Engine

When putting the tire on is an effective idea to install the bottom lug nut first, since it will help keep the tire in the right position to install the other lug nuts with ease. As a rule, starting the lug nuts by hand and turning them three or more threads will prevent stripping out the threads. Next, you will use the lug wrench to tighten the lug nuts little past finger tight. After all the lug nuts are snug, then the car can be lowered so the tire begins to touch the ground. Straight off the lug nuts can get their final torque and should be done so in a star or a criss-cross pattern. Afterward, the car can be lowered and the tools can be put away. By the way, it’s always a beneficial idea to check the lug nuts after traveling about ten miles to assure they are still

While the oil is draining, locate the oil filter it is white and oval. The oil filter is usually located on the side near the back. After, you locate the oil filter take it off with the oil filter wrench. Once the oil filter is off dispose of it in the trash, then get the new filter, and fill it up with oil before attaching it back to the motor. This step is called priming the car. Priming is when you basically jump starting the motor with whatever you took out. Now the car should be finished draining oil. You can tell its finish from when you look under the car near the motor and see no oil coming out. Once, that is noticed get the oil bolt and put it back in tight, but not too tight because that could strip the bolt out.

That is how you change your oil a simple process that saves you money and keeps your car running for as long as you need

iii. The oil should roughly take ten to fifteen minutes to drain completely. When the oil stops draining your ready to remove the oil filter. Just like before with the plug place the oil drain pan directly under oil filter. This is done because almost always their will still be a little left over oil in the filter. When removing the filter you want to turn the oil filter counter clockwise to release it from your vehicle.

First, you need to remove the oil fill cap under the hood so the oil will flow out freely. Be sure that you have a container for the used oil later; take it to recycle centers which are usually located around town. Remember that it is now illegal to dump oil anywhere. Next find the drain plug, which will be located on the bottom of the engine block. It is the only plug located usually in the middle of a black pan in the front of the vehicle. Be careful that you have the right plug because some transmissions are also equipped with a drain plug. Once the plug has been located, find the right size socket or wrench to fit it, and be careful not to round of the head of the drain plug when you are removing it. Then let the oil drain in to your container. When the pan has drained replace the plug, but do not over-tighten it because you can strip the treads out of pan. Next, you need to find the oil filter, which should be located on either side of the engine block. Then take the oil filter wrench and put it around the filter and remove the old filter. Then take your new filter and take a little

i. Step 1: Locate the oil filler cap on top of the engine. Remove it.

You will have to turn the lug nuts counter clockwise to loosen them. Do not remove the lug nuts all the way off the threaded shaft. Next, to get the wheel off the car, you have to raise the corner of the car where the flat is located.

Finally, you will now need to lower the car to the ground. Remove the flat tire from under the car. Crank the jack lowering the car to the ground. Do not fully lower it to the ground because you have to tighten the nuts again just to make sure you got it right. After everything is fully tightened, lower the car completely. Place the hub back on the wheel and remove the jack from under the car. Place the flat tire into your car and get it repaired if possible.

i. Note that this has to be done quickly, but not too quickly otherwise the car

Before pouring new oil into the engine block, the drainage bolt must be placed back into the car’s oil pan with the 10-millimeter socket wrench. This assures the new oil will not drip out into the old oil. To replace the old filter with a new one, the new oil must first be applied to the seal of the new filter. This lubes the seal on the new filter so it will not break due to friction. If it does break, the filter will leak and a new oil change will be required. Pouring the new oil in is a relatively easy step compared to all the other steps. To pour the new oil in, the engine oil cap must be removed. The recommended amount of oil and oil type, which is different for every car, can be found in the owners-manual or on the car dealer’s website. For instance, if the recommended amount of oil is 8 quarts, pour in 8 quarts, which can be measured by bottles (usually sold in 2 quart bottles), through a funnel into the engine block.

Clean the car properly: this is very important because the use of hard and non-automotive products can damage the finish of your car and make it faster. Spray the car first and wet it. Use water to spray dirt and other contaminants that will scratch your car if you immediately start using a sponge and water first. Also, do not clean your car in the sun on a hot day. Be sure to use warm water as it works best to loosen contaminants. After you wet your car, use a car wash solution and add to the water in a bucket. Follow the instructions in the bottle. Then wash the car. You will find it easier if you use a long-handled wash brush (most car

Normally when my husband and I get a vehicle we always start under the hood. First, check the oil. Without oil, people run the risk of seizing and locking up the engine and then it becomes a lot more expensive than just a few quarts of oil. Most people I have noticed, don’t know how often to change their oil. When using regular blend oil, it should be changed around every 3,500 miles. When purchasing synthetic oil, which is used in most vehicles today drivers should change it around 7,000 miles. After checking the oil, we check the tire pressure to ensure the correct lbs. of pressure required for the type of tires and vehicle we have. Other fluid levels to check include the coolant reservoir, anti-freeze levels, as well as transmission and brake fluid. Aside from fluids, when my husband would perform a tune-up on a vehicle new to us, he would also check the spark plugs and wires

The first step to cleaning your car is to clean everything out. You want to clean out anything that belongs inside of your house. For example, a bookbag, makeup, clothes, or anything else you have in your car. Next, clean out all the garbage. You may have plastic bags, food wrappers, or old papers that can be thrown out. You also might want to take any change out of your car into your piggy bank.

Once you reach 5 to 7 mph, let go of the depressed clutch quickly. If the engine starts, it’s a great job. But if it does not, press hard on the clutch again and release it.

Vehicle history is extraordinarily important for an oil change service. The vehicle history shows specific oil type used in the past and crucial dates and places the services were performed. Historical documents will help any new car or used car owner develop a service plan for the car’s engine. After choosing the desired oil