How to Change Oil in a Car Essay

Changing your engine oil is one of the single most important vehicle maintenance acts you can perform. Over time the oil breaks down and no longer performs its job the way it did when it was new. Your engine 's oil helps absorb heat from the engine and lubricates moving metal parts that would otherwise grind together. As you drive, the oil pump circulates oil within your engine and the oil filter catches the deposits that build up over time. The oil filter performs its own type of car maintenance by keeping the oil clean. But as the oil gets older, the number of deposits in the oil continues to build and the filter is unable to extract all of the material. When this happens, the color of the oil changes and it indicates the oil should be

Specific purpose: To inform the audience on how to change the oil in a vehical.

everything is okay; lower the car off the jack stands. Now that you're on flat ground, check the

Once you have the car in the air you will want to put some jack stands under each side and lower the car down on these, this will prevent the car from falling on you if the jack where to collapse, since jacks are only designed to pick the car up, not support it all day. Once the car is safely on the jack stands, you are ready to change the oil.

i. Step 1: Locate the oil filler cap on top of the engine. Remove it.

Oil lubricates the moving parts that are within the engine. It also absorbs heat so that the engine doesn’t overheat. Your oil needs to be changed every 3,000 to 5,000 miles. If you would rather change it yourself instead of taking it in somewhere to be done, follow these steps.

First, put the key into the ignation switch where located below the headlight compartment .

Therefore, you will raise the jack so that it almost touches the car. Once the jack is raised enough to just touch the car; position the jack so that it is not tilted; furthermore, make sure the jack is 6 – 12 inches behind the front or rear of the tire. When you are sure the jack is in position correctly; proceed by raising the jack, so that the car will rise off the ground. Remember you need to fit a fully inflated tire in place of the flat; therefore, make sure you jack the car up enough to get a fully inflated tire under there. Once you have the car off the ground; go ahead and remove the lug nuts with your hand. Now, grasp the wheel at 3 o’clock and 9 o’clock and pull the wheel straight off. Place the flat tire in the trunk; otherwise, it will be in the way while you are working. You will then, pick up the spare tire and line up the holes with the threaded shafts; then slide the spare tire onto the threaded shafts. Next, you will spin the lug nuts on by hand; indeed, you have to turn the lug nuts clockwise to tighten them.

In the winter only, I recommend letting your vehicle run a few minutes before starting. The oil is thicker when it is colder so when the vehicle runs it will warm the oil, making the oil flow easier.With the car off, safely elevate the vehicle with a jack or a set of ramps. Next, you want to align the bucket so it is under the oil pan plug. Proceed to unscrew the plug with the box end wrench. Be very careful not to be burned by the oil, because it may be hot. Do not drop the plug in the oil. Completely take off the plug and let the oil drain into the bucket. The next step is to use an oil filter wrench, to unscrew the old oil filter. The oil filter is usually a three to five inch tall cylindrical canister located relatively close to the oil pan. When the oil filter is completely off, dump any remaining oil from it into the bucket. When it is empty make sure to remove the gasket. The gasket is a rubber ring around the edge of the filter. Once everything is completed, come out from underneath the vehicle and set aside the old filter. Take the new oil filter out of the box and make sure it looks like the old filter. Take a little bit of the new oil into clean hands and smear it around the gasket of the new filter. This is done to “wake up” the gasket so it has an even seal when it is attached to the vehicle. Make sure to not get any foreign particles into the filter such as sand or dirt. Bring the new oil filter back underneath

it into the gas tank. Next check to see if you have weed eater line on the weed eater. After you

There is nothing better than having the self-satisfaction of doing something by yourself. If you don’t learn how to change your oil in your car, you could have to spend thousands of dollars on your car’s engine, or go to the auto parts store and spend around thirty dollars on oil and an oil filter. So listen up and save a couple dollars by learning how to change your own oil in your car.

C. To get moving onto the road there are some things that we have to do.

4.     Jack the car up about a foot to a foot and a half. Use the jack stands and put them on both sides of the car. ** This is a very important procedure; in case the jack fails (unlikely but can happen) you have something to hold up the car.

Next fill the bucket with the recommended ratio of water and soap. Using hot water will affect the cars wax so be sure to use cool water. Don't use more soap than the instructions say to use, because more soap removes more wax. If possible use less soap to help save your car.

Before you start, park your car out of direct sunlight and on a hard surface. You should park on concrete if possible; this will keep dirt and mud from splashing up on the car when you rinse it off. Now fill up your bucket with water and mix the soap as directed. Next soak the car down with water; do this a couple of times. The water helps to loosen the dirt and grime. Submerge your wash cloth completely in the bucket of soap and water. Do not ring out the towel, take it dripping wet and start to wash you car. Start at the top and work your way down, using the wash cloth in a circular motion with a little bit of pressure. If it is a hot day, then you probably need to wash the car in sections. For example, wash the roof, windshield, and hood, and then set the wash cloth back in the bucket