Lab Report Physics Lab

because each of the objects displaced the water by 1 mL, their mass over that mL is their density.

Students in an AP Physics lab perform an electrostatics experiment involving two charged spheres suspended

Experiment 2 “Density” was about how to measure the mass and volume and determine the density of water, alcohol, and a solid. For this lab, we begin by calculating the mass of empty graduated cylinder and the mass of 25 mL of tap water. After taking the mass of water and cylinder, we record it on “Density of Water: Data Table”. Since we did not have enough time of complete the whole lab, so we skipped the procedure to measure the density of alcohol. We jumped to the next procedure, which was density of a solid. For that we used a copper and it density 8.95. For this lab, my partner and I did not make any mistakes or errors. But, for better improvement I think we should have more time to complete the whole lab. I felt like we was rushing through

Procedure: Using distilled water, premeasured containers and objects determine displacement of fluids and density of objects. Use ice and heat measure temperatures in Celsius, Fahrenheit and Kelvin.

There are several sources of error to this experiment due to random and systematic errors. The only source of random error was the measurement that we took through the graduated cylinder which was only accurate to the nearest 1%. We took the largest error from this one percent, which was +/- 3. The largest relative error this yielded was only 3%, so this did not affect how precise this experiment was too much. We can still make this more precise by making the masses of the water larger. For example if we started the masses at 300mL and went up by 50mL, the largest error this would yield would be 2% due to the largest error being +/- 5. This would cause smaller errors in the amount of water.

The purpose of this lab is to test substances and to determine the physical and chemical properties of substances.

In this lab experiment our main focus was to get skillful in using tools such as the metric ruler, balances, thermometer, and graduated cylinder to capture measurements of length, mass, temperature and volume. Additionally, this lab helped us to become more familiar with the uncertainty of measurements, as well as becoming efficient with rounding our measurements to the correct numbers of significant figures. Our results are measured consistently with rounding to the closest answer we could possibly acquire as the data can tell you.

Abstract: The objective of the lab is to determine the volumes of the polystyrene spheres with three different measuring tools: Water Displacement, Analytical Scale, and Triple Beam Balance Scale. The experiment is meant to help understand the concept and application of precision and accuracy in experimental measurements. Accuracy is a measure of how closely the results of repeated measurements are to the true value of what is being measured. Precision is the variability in the results from the repeated measurements, and how close the repeated measurements were to one another. In this lab, the method for measuring the volume of the polystyrene spheres is done with the previously stated tools: Water Displacement, Analytical Scale, and Triple Beam Balance Scale. The standard deviation for the entire classes volumes and masses are recorded to determine the densities.

2. In order to calculate the density of a solid or liquid sample, what measurements are needed?

Abstract: This experiment introduced the student to lab techniques and measurements. It started with measuring length. An example of this would be the length of a nickel, which is 2cm. The next part of the experiment was measuring temperature. I found that water boils around 95ºC at 6600ft. Ice also has a significant effect on the temperature of water from the tap. Ice dropped the temperature about 15ºC. Volumetric measurements were the basis of the 3rd part of the experiment. It was displayed during this experiment that a pipet holds about 4mL and that there are approximately 27 drops/mL from a short stem pipet. Part 4 introduced the student to measuring

The volume of a small test tube and a thin-stemmed pipet were determined in this section of the lab. Water was poured into a small test tube until the water reached the very top edge of the test tube. The test tube was then emptied into a plastic 25 mL graduated cylinder and volume was measured and recorded into data table 3. A think-stemmed pipet was completely filled with water. Drops were carefully counted and emptied into the empty plastic 25 mL graduated cylinder until the water level reached 1 mL. The number of drops in 1 mL was recorded into data table 3. The thin-stemmed pipet had a total volume of 4 mL and that was also recorded into data table 3.

Throughout lab one we were introduced to many different forms of measurement, whether its using a ruler too measure length, a digital scale to measure weight, and also many different sized and shaped flasks to measure different volumes. Another key measurement of this lab was to teach the

1. How well does the appearance and solubility, of iodine and zinc respectively compare with information presented in the CRC handbook of chemistry and Physics? Our results for the appearance and solubility of iodine and zinc were very similar to the results given on the table. The only thing that was different was the result for Mineral oil.

From this lab, we can learn how using the volume and mass of an object can be used to the calculate density, and how the density can help you to identify what substance the object is made of. We began the lab by obtaining object C and recorded the physical properties of the substance. Next, the object was placed onto a scale to determine the mass in grams (56.56g). We used a ruler to measure the radius of the base (.6cm) and the height (5cm) of the cylinder-shaped substance. We plugged these measurements into the volume formula for a cylinder (V =

2. Vary the inbuilt d. c. supply voltage in steps of 0.1V and note down corresponding voltmeter and ammeter readings.