Limiting Reactant Lab

The purpose of this lab was to determine the limiting reactant in a mixture of to soluble salts and the percent composition of each substance in a salt mixture.

Used stirring rods to completely remove copper from that wire. And then completed the removal of copper using 5 drops of 6M HCl, adding it onto copper. There will produced copper in a solution. Connected Buchner flask to the vacuum line and place filter paper in it to completely washed off the copper. Then, add 95% ethanol to copper and leave it for 1 min and turned section back for 5 mins. Measured mass of clean, dry watch glass. Transfer copper to watch glass and dry it under heat lamp for 20 mins, allowed it to cool to room temperature and then accurately determine its mass.

7.The air dried filter paper was then placed on the weighing scale and results were recorded

In this task the concentration of an unknown sample of copper sulphate using colorimetry was used to find the concentration. In this investigation copper sulphate was used which is CuSO4.5H20 as a formula. To make a standard solution which was 1M, the same clean equipment was used to make up the standard solution as used to make sodium carbonate. However there was one difference and that was that the hot distilled water was used to dissolve the copper sulphate crystals. There had to be enough hot water in order to dissolve the crystals into the beaker and then add cold distilled water to cool the solution.

The purpose of the experiment is to cycle solid copper through a series of five reactions. At different stages of the cycle, copper was present in different forms. First reaction involves reaction between the copper and nitric acid, and copper changed from elemental state to an aqueous. The second reaction converted the aqueous Cu2+ into the solid copper (2) hydroxide. In the third reaction Cu(OH)2 decomposed into copper 2 oxide and water when heated. When solid CuO reacted with sulfuric acid, the copper returned to solution as an ion (Cu2+). The cycle of reactions was completed with the reaction where elemental copper was regenerated by Zn and Cu

Washing of the copper is necessary in this experiment to separate the iron from the copper and make sure the iron is not counted in the mass of the copper.

Obtain a 50 mL beaker for the experiment. In the first part of the experiment, you dissolve the zinc core of a penny and leave the copper covering intact by putting four notches in

The Cu Later lab experiment is designed to allow you to practice lab skills in implementing and performing a series of reactions. Specifically, four types of chemical reactions will occur: oxidation/reduction; double replacement; single replacement; and decomposition. You will begin with a known amount of copper metal, which, after progressing through several steps, is reproduced. In this experiment you will observe and record the various changes such as heat, color changes, and production that occur. This procedure is used to observe some chemical reactions of copper and its compounds while also performing the lab appropriately as to retain the copper as much as

13) When the tray is thoroughly dry, determine its mass. Record the mass in the data table. You have to wait until day three to weigh the copper.

The limiting reactant of a chemical reaction is the substance that places an upper bound on the amount of product that the reaction can produce. The limiting reactant places this upper bound because the reaction must stop once all of the limiting reactant is consumed.

XIII. Carefully remove the copper metal from the filter paper onto the watch glass. (with a spatula) Place a 400 ml beaker on a hot plate contained with water. Carefully place the watch glass before the water boils to dry the copper metal. (Use the tongs to handle the hot watch glass)

3) Repeat the drying process just to be sure that the copper is completely dry, and again determine the mass of the copper and the beaker.

Purpose: The purpose of this experiment was to observe the many physical and chemical properties of copper as it undergoes a series of chemical reactions. Throughout this process, one would also need to acknowledge that even though the law of conservation of matter/mass suggests that one should expect to recover the same amount of copper as one started with, inevitable sources of error alter the results and produce different outcomes. The possible sources of error that led to a gain or loss in copper are demonstrated in the calculation of percent yield (percent yield= (actual yield/theoretical yield) x 100.

The lab performed required the use of quantitative and analytical analysis along with limiting reagent analysis. The reaction of Copper (II) Sulfate, CuSO4, mass of 7.0015g with 2.0095g Fe or iron powder produced a solid precipitate of copper while the solution remained the blue color. Through this the appropriate reaction had to be determined out of the two possibilities. Through the use of a vacuum filtration system the mass of Cu was found to be 2.1726g which meant that through limiting reagent analysis Fe was determined to be the limiting reagent and the chemical reaction was determined to be as following:-

Assign one member of the group to gently stir solution with a thermometer (See figure 2)