Measuring the Melting Points of Compounds and Mixtures Essay

An Erlenmeyer flask was used to accommodate the largest volume of recrystallization solvent calculated and was cooled in an ice bath to increase the yield of crystals. The solid was collected by vacuum filtration and washed with a small amount of ice water. The product is then dried to a constant mass by use of an oven and weighed. A small amount of the unknown was compared to two samples of acetanilide and phenacetin for a melting point range to determine the identity. The temperature of the unknown was recorded when the first trace of liquid can be seen and when the unknown was completely liquid.

After each of the solids were completely dry, each was placed into a MelTemp device. The temperature at which each solid began to melt and completed melting was recorded.

The mixture was transferred to an ice bath to crystallize the product, after which the product was collected by vacuum filtration on a Hirsch funnel, washing the flask with small aliquots of cold xylene and pouring the solution over the crystals, allowing the vacuum to thoroughly dry the product. Additional drying was achieved by transferring the product to filter paper and pressing the crystals to remove any excess moisture. The product was then weighed and a melting point determined. A comparative TLC was run in Hexanes:Ethyl Acetate solvent against maleic anhydride to verify the purity of the

In this lab, liquid-liquid extraction was performed to isolate a mixture of benzocaine and benzoic acid. 2.0107 grams of the mixture was first weighed out for the trials. When HCl was added to the mixture for the first acid extraction of benzocaine, an emulsion formed during inversion and venting that prevented a defined separation of the two layers. 8 mL of water was therefore added before continuing the extraction. The addition of NaOH then turned the top aqueous layer basic, indicated by the pH strips that turned blue when tested. A vacuum filtration isolated 0.29 grams of benzocaine and a MelTemp apparatus measured the crystal’s melting point ranges to be 85.1C-87.4C. For the base extraction of benzoic acid, the aqueous layers were retrieved

The vial was removed from the heat and cooled to room temperature. The spin vane was rinsed with 2-3 drops of warm water over the conical vial. The vial was cooled to room temperature then placed in an ice bath for 15 minutes. The liquid was decanted from the mixture and the resulting crystals were dried on filter paper. The crystals were then placed on a watch glass for further drying. The crystals were weighed and a small sample was placed into a capillary tube for melting point determination.

In determining the melting point range of the aspirin, a capillary tube (sealed at one end) was one-third-filled with the dried aspirin. The capillary tube and a thermometer were immersed in an oil bath. The temperature at which the solid started to melt and the temperature when the entire sample was completely liquefied were recorded as the melting point temperature range.

The product was then suspended in 2 ml of water with a stir rod in a 50 ml Erlenmeyer flask and heated to boiling. Water was added in one milliliter increments until all the product was dissolved (18 ml added total). The saturated solution was allowed to slowly cool, and gradual white crystal formation was observed. Recrystallized product was collected once more by suction filtration with the Hirsch funnel once crystallization ceased. Collected product dried on a watch glass for a week, weighed 0.14 g (1.2 mmol), and the melting point was 139°-141°

4- chlorobenzoic acid which was the aqueous layer has a theoretical melting point of 240-243°C, the organic layer, 4-chlorobenzyl alcohol has a theoretical melting point of 68-71°C. During our experiment we were unable to collect any data for the organic

pH was recorded every time 1.00 mL of NaOH was added to beaker. When the amount of NaOH added to the beaker was about 5.00 mL away from the expected end point, NaOH was added very slowly. Approximately 0.20 mL of NaOH was added until the pH made a jump. The pH was recorded until it reached ~12. This was repeated two more times. The pKa of each trial are determined using the graphs made on excel.

Discussion: As seen in the melting point determination, the average melting point range of the product was 172.2-185.3ºC. The melting points of the possible products are listed as 101ºC for o-methoxybenzoic acid, 110ºC for m- methoxybenzoic acid, and 185ºC for p- methoxybenzoic acid. As the melting point of the sample

Identifying this organic acid was an extensive task that involved several different experiments. Firstly, the melting point had to be determined. Since melting point can be determined to an almost exact degree, finding a close melting point of the specific unknown can accurately point to the identification of the acid. In this case the best melting point

The week after, a recrystallization was performed on the previous week’s crude product. The product ethereal solution was first heated on a steam bath until dry. During the heating, a beaker of methanol was collected and also placed on the steam bath. Once the product was dry, it was cooled to room temperature and then placed in an ice-water bath. The now boiling methanol was added to the crude crystals and a recrystallization was performed. Once completed, the now purified product was collected via Buchner vacuum filtration and stored in drawer to dry for a week. Afterwards, a melting point range of the purified product was obtained by using a Mel-temp apparatus. Lastly, an

Solubility – Very soluble (water), Freely soluble (methylene chloride, chloroform, alcohol), Slightly soluble (acetone) and Insoluble (ether).6 Melting point - 120°C or 248°F.5

Melting range would be closely related to a mixed sample whose constituents are most identical. In other words, melting point will have a wide range and would be below 200°C and above 95°C.

The temperature at which polymer transmit into crystalline form to determine the melting point. The polymer of low-molecular substance exist very low melting point and this happened when polymer chain is dispersed. In physical state melting point is very difficult to calculate. Polymer will decompose at high temperature rather than melts. It is also known as crystalline melting temperature.