My Egg Autobiography

Once I have examined the eggs, I will then take them out of the containers and place them on a paper towel. Once I have dried the eggs off, I will start to test each one to determine how high each one can bounce and which one will break first. I will do this experiment by dropping each egg no more than 2 inches from a tabletop. I will make a note of how many bounces it took before each egg broke. I will record this on my data sheet. Once I have completed this experiment, then I will be able to answer the question I have.

One Quart Zip-Lock bag and fill it with 20mL of Hydrochloric acid, take a taped off Easter egg and fill it with 5.15g of baking soda. Insert egg in corner of bag and close bag. When ready to deploy flick egg to release baking soda into the acid to create a gas to fill the bag.

The science behind this project is conservation of momentum, conservation of energy, force time trade off, and Newton’s first, second, and third laws. These can be used to ensure the eggs safety before, during, and after the egg is dropped. When dropped there are many forces that act upon the egg, some of these are gravity, speed, velocity, and acceleration. When the project is built it is important that this is taken into account. If the science behind all of it is used properly the egg should not break when it hits the ground.

Grab your styrophome cup and fill it appotrpiratly with water until the egg is weighed down

For this project, I made a capsule for an egg that is to be dropped from about twenty feet. This capsule that I made was not what I was thinking at first but when I started to build it, I saw that this capsule would hold better than the one that I was thinking which was a triangular capsule with the egg in the middle but I saw later one that the egg would break if it hit one of the flat sides. The capsule is a cube that is made out of the tongue depressors and I used most of the yarn for the big cage and I used the Elmer’s glue to glue the tongue depressors together. I used pieces of the paper clips to hold the popsicle sticks together with the tongue depressors and some

The purpose behind the egg drop project is for students to understand the concept of momentum, collision, impulse and force. To do this, they will create a protective carrier that will surround the egg. The egg will then be dropped from a certain height. The device that is created should weigh enough to increase the time of impact, therefore decreasing the force of impact on the egg so it doesn’t crack.

Drain the hot water and instantly place the eggs in cold water so that they become cool to be peeled easily.

many western politicians and media sources the ammunition to further propagate Islamophobia by exploiting the attack.

We had to do an egg drop so when it is dropped from 20 ft it wouldn’t crack.. But I really didn’t have any background knowledge on egg drops because I never did one. But I did know that by putting a plate on the bottom it would make it float down and not fall. So when it was dropped from 20ft it wouldn’t crack.

Procedure: First you need your plastic cup and stand it up straight if it isn't already. Then open your bag of sugar and pour enough to fill up your cup about two- thirds of the way. Then place the egg in the center and push and turn into the sugar until you can’t see it

Have you ever heard of drop the egg challenge? Well, I’m here to tell you about my drop the egg challenge. You have to drop the egg from a distance in the air, but the egg cannot crack. Yes, it is possible. Here’s the supplies my partner and I used. We had a bowl, rocks, cardboard, four paper towel rolls, gorilla tape, hot glue gun, and of course an EGG! First we placed the rocks in the bowl, then glued a square foot piece of cardboard on top of the bowl, next we glued/taped the paper towel rolls (on top of the cardboard glued to the bowl), after we cut a small circle in a small square piece of cardboard (so the egg can fit in it), therefor we glued the egg in the circle and we cut a half of a bottle and put it

When I went to Evergreen Park, I saw a lot of children with their parents. I went to ask them about what happened. They said this is Easter egg hunt which they define as a game for children and children have to find eggs. An eggs have different colors that was beautiful. This day for Christin people and they celebrated in spring season. In addition, this day was on Saturday (8 April, 2017) and they stared this game at 12 p.m. to 1:30 p.m.

Procedure: Materials needed for this lab are: two cardboard boxes, with one bigger than the other, polyfill (one handful), hot glue (a couple of sticks), hot glue gun, elmers glue, dixie cups(at least two, but may want/need extra) , eggs (minimum of one but two is allowed), saran wrap, sandwich baggie(s), feathers, colorful thin foam, sequins, balloons, scissors, ruler, timer, calculator, scale, duct tape and/or masking tape, insulation pipe, string, paint, paint brushes, sharpie markers (to decorate egg with) Start by coming up with an initial design to make the egg drop container, by having an actual drawing, also write down the materials needed and if needed a budget of how much you can spend. Also you will need a way to keep track of the

Our contraption is made of balloons, string, Popsicle sticks, cups, cotton, and rubber bands. In this experiment gravity, drag, and impact are demonstrated. Gravity is the force that pulls objects towards each other. This is when the egg is falling to the ground. The drag is when the object is acting is the opposite direction. This is the balloons attached to the egg which slows it down. Finally impact is the shock when to objects collide. This is why cotton balls are on the bottom to absorb the impact. These are all Newton's law of motion.

Drag, gravity, and impact everything that affects the egg drop project. Drag is a very forceful pull. Drag and gravity work together in a way because if there wasn't gravity to pull the object to the ground than drag wouldn't be able to come into play. Gravity is the force that pulls the object to the ground but drag is what makes the object slow down when gravity is pulling it through the air. The higher you drop the object from doesn't always mean that the object will maintain a higher speed. Once it reaches its terminal velocity (the speed where the drag from the air is equal to the force of gravity), it will stop accelerating and maintain a certain speed. Impact is another huge factor in this project because without impact than the egg