Naphthalene And Salicylic Acid Lab Report

The objective of this experiment is to separate a 50:50 mixture of benzoic acid and benzil by using macroscale extraction. In the experiment, organic solvent diethyl ether is used. After adding 1.0 gram of the 50:50 mixture of benzoic acid and benzil to a 25ml Erlenmeyer flask, diethyl ether was added to the flask to dissolve the mixture. Benzoic acid and benzil dissolve in diethyl ether. Once the mixture dissolved in

This experiment combined all the knowledge of the previous labs performed throughout the semester. An unknown mixture containing an organic acid or base and an organic neutral compound in nearly equal amounts needs to be separated to its separate components. An understanding of solubility, extraction, crystallization and vacuum filtration is necessary in order to

In the first acid extraction of benzocaine, the compound was dissolved in the organic solvent of dichloromethane. When the mixture was shaken with HCl, benzocaine’s amine group gained a proton and became more soluble in water than dichloromethane. This allowed the newly formed hydrochloric salt to migrate to the aqueous layer. However, the addition of NaOH to the acidic aqueous layer regenerated benzocaine by deprotonation, making it insoluble in the aqueous layer. The precipitation of an ionic salt was therefore recovered by vacuum filtration and had a tested melting point range of 85.1C-87.4C compared to 88C-90C, the literature melting point of benzocaine. The similarity in melting point ranges, but low percent yield of 30.37% proves that the extract was somewhat successful. Lower yields may be the result of spillage performed in the lab. In the second basic extraction, the organic layer now included benzoic acid and benzamide. When treated with NaOH to deprotonate benzoic acid, the newly formed sodium benzoate transitioned to the aqueous layer as a sodium salt. Benzoic acid is regenerated once again after the addition of HCl and became insoluble in the aqueous layer after protonation. Its precipitation was then filtered out for a 65.87% recovery. Compared to its literature melting point of 122.41C, the resulting 120.9C-123.5C melting range of the sample also supports the accuracy of the separation due to its similarities and high percent yield. In conclusion, the usage of base and acid liquid extraction was mostly successful in this experiment because it was able to efficiently and properly isolate the impure mixture into two separate components of benzocaine and benzoic acid. By performing the techniques of extraction and vacuum filtration, the similarities between literature and tested

Abstract: One mixture of two unknown liquid compounds and one mixture of two unknown solid compounds were separated, isolated, purified, and characterized by boiling point. Two liquid unknowns were separated, isolated, and purified via simple distillation. Then, the process of an acid-base extraction and washing were used to separate two unknown compounds into two crude compounds: an organic acid and a neutral organic compound. Each crude compound was purified by recrystallization, resulting in a carboxylic acid (RCO2H) and a pure organic compound (RZ). The resulting mass of the pure carboxylic acid was 1.688g with a percent recovery of 31.80%, the boiling range was 244-245 °C, and its density was 2.0879g/mL. The resulting mass of the pure organic solid was 2.4902g with a percent recovery of 46.91%, the boiling range was 52.0-53.4°C, and its density was 1.5956 g/mL.

The objective of this extraction experiment was to achieve a comprehensive understanding, as well as master the practice, of the technique of separating various individual components of a compound.

In order to isolate benzoic acid, benzocaine and 9-fluorenone, each component needed to be separated from one another. All three compounds began together in one culture tube, dissolved in methylene chloride and formed into a homogenous mixture. In this culture tube, two milliliters of aqueous three molar hydrochloric acid was added, which immediately formed two layers, the top acidic aqueous layer was clear in color and contained benzocaine, and the bottom organic formed was yellow and contained benzoic acid and 9-fluorenone. Benzocaine’s amino group is protonated by the aqueous layer hydronium. This protonation forms the conjugate acid of benzocaine, benzocaine hydrochloride. Thus, the conjugate acid, benzocaine hydrochloride is a salt in which is soluble in water and furthermore can be isolated from the organic mixture. When testing out the pH levels in benzocaine, the pH test strip was dark blue in color, indicating a pH level of around 5 to 7. When isolating benzoic acid, two milliliters of aqueous three molar sodium hydroxide was added, which deprotonates the carboxylic group in benzoic acid, forming its conjugate base, sodium benzoate. As with benzocaine hydrochloride, sodium benzoate is a water soluble ionic salt in the aqueous layer that can then be separated from the bottom organic layer containing the 9-fluorenone. The pH test strip was a vibrant red for benzoic acid, indicating a pH of 2. Now the 9-fluorenone is left, deionized water is added to remove any excess

The purpose of this experiment is to practice common organic laboratory techniques inside the lab to get one oriented to the basic methods of procedure that can be used for later experiments. This experiment involves the separation of benzoic acid from a more crude form, consisting of benzoic acid, methyl orange, a common acid/base indicator, and cellulose, a natural polymer of glucose (Huston, and Liu 17-24). The technique that is used to perform this separation is called extraction. Extraction is a systematic process of separating mixtures of compounds, taking advantage of the affinity differences of compounds to separate them (Padias 128-37). This technique recognizes the principle that “like dissolves in like,” that is,

1.5mL of phosphoric acid including 3-4 boiling chips were also added to the 25mL flask. The short path distillation apparatus was set up as shown in Figure 1. A heating mantle was used to heat up the 25mL flask. The solution was distilled to the receiving flask until a small amount of liquid remained in the initial RBF flask. At this point the presence of thick grey smoke pulling over into the entire apparatus was observed. The apparatus was then left to cool down. Through the use of pasture pipette, the aqueous layer from the distilled solution was drawn out. Sodium carbonate was then added to the remaining organic solution in order to check the pH and to verify the basicity of the solution. The aqueous layer was again drawn out from the solution. Next, 0.5g of sodium sulfate was added to the remaining organic layer and was swirled until the liquid appeared to be dry and clear. The alkenes were transferred into a clean 10mL flaks using another clean pasture pipe. The apparatus from the first distillation was rinsed off with

Three grams of a mixture containing Benzoic Acid and Naphthalene was obtained and placed in 100 ml beaker and added 30 ml of ethyl acetate for dissolving the mixture. A small amount (1-2 drops) of this mixture was separated into a test tube. This test tube was covered and labelled as “M” (mixture). This was set to the side and used the following week for the second part of lab. The content in the beaker was then transferred into separatory funnel. 10 ml of 1 M NaOH added to the content and placed the stopper in the funnel. In the hood separatory funnel was gently shaken for approximately one minute and vent the air out for five seconds. We repeated the same process in the same manner one more time by adding 10ml of 1M NaOH.

Objective: The objective of this experiment is to use acid-base extraction techniques to separate a mixture of organic compounds based on acidity and/or basicity. After the three compounds are separated we will recover them into their salt forms and then purify them by recrystallization and identify them by their melting points.

Experiment 4A: Determination of a Partition Coefficient for Benzoic Acid in Methylene Chloride and Water, and Experiment 4B: Solvent Extraction I: Acid-Base Extraction Using the System Benzoic Acid, Methylene Chloride, and Sodium Bicarbonate Solution

Distillation is a method of separating two volatile chemicals on the basis of their differing boiling points. During this lab, students were given 30 mL of an unknown solution containing two colorless chemicals. Because the chemicals may have had a relatively close boiling point, we had to employ a fractional distillation over a simple distillation. By adding a fractionating column between the boiling flask and the condenser, we were able to separate the liquids more efficiently due to the fact that more volatile liquids tend to push towards the top of the fractionating column, thereby leaving the liquid with the lower boiling point towards the bottom. After obtaining the distillates, we utilized a gas chromatograph in order to analyze the volatile substances in the gas phase and determine their composition percentage of the initial solution. Overall, through this lab we were able to enhance our knowledge on the practical utilization of chemical theories, and thus also demonstrated technical fluency involving the equipment.

Dispense .5 mL water into the already weighed conical vial, replace cap and face insert on its down side.

The purpose of this experiment was to use solvent extraction techniques in order to separate a mixture consisting of a carboxylic acid (p-toulic acid), a phenol (p-tert-butylphenol), and a neutral compound (acetanilide). Extraction is the process of selectively dissolving one or more of the compounds of a mixture into an appropriate solvent, the solution that contains these dissolved compounds is called an extract (Manion, 2004).

2-naphthol has a molecular weight of 144.17 g/mol, with a density of 1.22 g/cm3. The melting point of 2-naphthol is in the range of 121 to 123 °C. The stock solution of 2-naphthol has a concentration of 1.9844E-3 M.