Nitrating Acetanilide and Methyl Benzoate: Electrophilic Aromatic Substitution

Melting Point Data Table Compound Aspirin Caffeine Salicylamide Actual MP (ºC) 93 - 98 260 - 262 96 - 102 Expected MP (ºC) 135 236 140 Percent Error (%) ~30% ~12% ~30%

Perform the following with three 0.05g samples of unknown and the following solvents: methanol, water and toluene

2. The purpose of the thiosulfate in this reaction is the pH testing of bleach substances. If one first adds sodium thiosulfate to such solutions, it will neutralize the color-removing effects of bleach and allow one to test the pH of bleach solutions with liquid

The Purpose of this experiment is for the students to learn how to use sodium borohydride to reduce benzil to its secondary alcohol product via reduction reaction. This two-step reaction reduces aldehydes by hydrides to primary alcohols, and ketones to secondary alcohols. In order for the reaction to occur and to better control the stereochemistry and yield of the product, the metal hydride nucleophile of the reducing agents such as LiH, LiAlH4, or NaBH4 must be carefully chosen. Being that LiAlH4 and NaBH4 will not react with isolated carbon-carbon double bonds nor the double bonds from aromatic rings; the chosen compound can be reduce selectively when the nucleophile only react with

The recrystallization technique utilizes the ability of a compound to dissolve within a hot solvent and produce a solution. As this solution cools, the solute reforms without impurities in a crystal lattice structure.1 For this to work properly, an appropriate solution that will not dissolve the solute at low temperatures, but will at high temperatures, must be used.1 There is no single solvent that will work well for every solute’s recrystallization; different solvents are better suited for some solutes than others.2 Some impurities that do not dissolve within the solvent can be filtered out while the solution is still hot, while other impurities that readily dissolve within the solvent shouldn’t recrystallize with the pure substance (as they are not concentrated enough to

The product was placed in a Craig tube and several drops of hot (100°C) solvent (50% water, 50% methanol, by volume) was added and heated until all of the crystals dissolved. The Craig tube was plugged and set in an Erlenmeyer flask to cool. Crystallization was induced once the mixture was at room temperature by scratching the inner wall of the tube. It was then placed into an ice bath for ten minutes until crystallization was complete. The tube was then

The product was then suspended in 2 ml of water with a stir rod in a 50 ml Erlenmeyer flask and heated to boiling. Water was added in one milliliter increments until all the product was dissolved (18 ml added total). The saturated solution was allowed to slowly cool, and gradual white crystal formation was observed. Recrystallized product was collected once more by suction filtration with the Hirsch funnel once crystallization ceased. Collected product dried on a watch glass for a week, weighed 0.14 g (1.2 mmol), and the melting point was 139°-141°

No correction had to be made to the melting points because the standard melted in the range labeled on the bottle. The melted point observed is the correct melting point.

6. Purpose: to clarify the mechanism for the cycloaddition reaction between benzonitrile oxide and an alkene, and to test the regiochemistry of the reaction between benzonitrile oxide and styrene; to purify the crude product of either trans-stilbene, cis-stilbene, or styrene reaction.

Discussion: As seen in the melting point determination, the average melting point range of the product was 172.2-185.3ºC. The melting points of the possible products are listed as 101ºC for o-methoxybenzoic acid, 110ºC for m- methoxybenzoic acid, and 185ºC for p- methoxybenzoic acid. As the melting point of the sample

Aromatic compounds can undergo electrophilic substitution reactions. In these reactions, the aromatic ring acts as a nucleophile (an electron pair donor) and reacts with an electrophilic reagent (an electron pair acceptor) resulting in the replacement of a hydrogen on the aromatic ring with the electrophile. Due to the fact that the conjugated 6π-electron system of the aromatic ring is so stable, the carbocation intermediate loses a proton to sustain the aromatic ring rather than reacting with a nucleophile. Ring substituents strongly influence the rate and position of electrophilic attack. Electron-donating groups on the benzene ring speed up the substitution process by stabilizing the carbocation intermediate. Electron-withdrawing groups, however, slow down the aromatic substitution because formation of the carbocation intermediate is more difficult. The electron-withdrawing group withdraws electron density from a species that is already positively charged making it very electron deficient. Therefore, electron-donating groups are considered to be “activating” and electron-withdrawing groups are “deactivating”. Activating substituents direct incoming groups to either the “ortho” or “para” positions. Deactivating substituents, with the exception of the halogens, direct incoming groups to the “meta” position. The experiment described above was an example of a specific electrophilic aromatic

To apply thermal analysis to the two-component system, naphthalene-biphenyl at atmospheric temperature. The analysis will be represented by a solid-liquid phase diagram (freezing point diagram).

Abstract: This procedure demonstrates the nitration of methyl benzoate to prepare methyl m-nitrobenzoate. Methyl benzoate was treated with concentrated Nitric and Sulfuric acid to yield methyl m-nitrobenzoate. The product was then isolated and recrystallized using methanol. This reaction is an example of an electrophilic aromatic substitution reaction, in which the nitro group replaces a proton of the aromatic ring. Following recrystallization, melting point and infrared were used to identify and characterize the product of the reaction.

Once cooled, the mixture was then transferred to a separatory funnel using the funnel while avoiding adding the boiling chip. 10 ml of water was then added to the mixture. The mixture was gently shaken and the phases were allowed to separate. The funnel was then unstopped and the lower aqueous phase was drained into a beaker. 5 ml of 5% aqueous NaHCO3 was added and then shaken gently. A great deal of caution was taken into consideration because of the production of carbon dioxide gas which caused pressure to develop inside the funnel. The pressure needed to be released so the funnel was vented frequently. The phases were allowed to separate and the lower aqueous phases was drained into the beaker. After draining, 5 ml of saturated NaCl was added to the funnel and then shaken gently. Once again, the phases were allowed to separate and the lower aqueous phase was drained into a beaker. An ester product was produced and was transferred into a 25 ml Erlenmeyer flask. This organic product was then dried over anhydrous Na2SO4 to trap small amounts of water in its crystal lattices thus removing it from the product. Finally the ester was decanted, so that the drying agent was excluded from the final product.

In this synthesis, 2.0g of benzophenone was dissolved in 50ml isopropyl alcohol in 50ml Erlenmeyer flask. In this solution, one drop of glacial acetic acid was added. It was then filled with isopropyl alcohol up to the brim. After, the flask was stoppered using a well-rolled cork. It was ensured that very little air as possible was trapped inside the flask. It was tightly bind using a parafilm. The flask was inverted and exposed to sunlight outside the laboratory.