Of The Melting Point Of Benzoic Acid And Erlenmeyer Fask

An Erlenmeyer flask was used to accommodate the largest volume of recrystallization solvent calculated and was cooled in an ice bath to increase the yield of crystals. The solid was collected by vacuum filtration and washed with a small amount of ice water. The product is then dried to a constant mass by use of an oven and weighed. A small amount of the unknown was compared to two samples of acetanilide and phenacetin for a melting point range to determine the identity. The temperature of the unknown was recorded when the first trace of liquid can be seen and when the unknown was completely liquid.

After each of the solids were completely dry, each was placed into a MelTemp device. The temperature at which each solid began to melt and completed melting was recorded.

The mixture was transferred to an ice bath to crystallize the product, after which the product was collected by vacuum filtration on a Hirsch funnel, washing the flask with small aliquots of cold xylene and pouring the solution over the crystals, allowing the vacuum to thoroughly dry the product. Additional drying was achieved by transferring the product to filter paper and pressing the crystals to remove any excess moisture. The product was then weighed and a melting point determined. A comparative TLC was run in Hexanes:Ethyl Acetate solvent against maleic anhydride to verify the purity of the

Experiment 55 consists of devising a separation and purification scheme for a three component mixture. The overall objective is to isolate in pure form two of the three compounds. This was done using extraction, solubility, crystallization and vacuum filtration. The experiment was carried out two times, both of which were successful.

The recrystallization technique utilizes the ability of a compound to dissolve within a hot solvent and produce a solution. As this solution cools, the solute reforms without impurities in a crystal lattice structure.1 For this to work properly, an appropriate solution that will not dissolve the solute at low temperatures, but will at high temperatures, must be used.1 There is no single solvent that will work well for every solute’s recrystallization; different solvents are better suited for some solutes than others.2 Some impurities that do not dissolve within the solvent can be filtered out while the solution is still hot, while other impurities that readily dissolve within the solvent shouldn’t recrystallize with the pure substance (as they are not concentrated enough to

In this lab, liquid-liquid extraction was performed to isolate a mixture of benzocaine and benzoic acid. 2.0107 grams of the mixture was first weighed out for the trials. When HCl was added to the mixture for the first acid extraction of benzocaine, an emulsion formed during inversion and venting that prevented a defined separation of the two layers. 8 mL of water was therefore added before continuing the extraction. The addition of NaOH then turned the top aqueous layer basic, indicated by the pH strips that turned blue when tested. A vacuum filtration isolated 0.29 grams of benzocaine and a MelTemp apparatus measured the crystal’s melting point ranges to be 85.1C-87.4C. For the base extraction of benzoic acid, the aqueous layers were retrieved

The product was placed in a Craig tube and several drops of hot (100°C) solvent (50% water, 50% methanol, by volume) was added and heated until all of the crystals dissolved. The Craig tube was plugged and set in an Erlenmeyer flask to cool. Crystallization was induced once the mixture was at room temperature by scratching the inner wall of the tube. It was then placed into an ice bath for ten minutes until crystallization was complete. The tube was then

The product was then suspended in 2 ml of water with a stir rod in a 50 ml Erlenmeyer flask and heated to boiling. Water was added in one milliliter increments until all the product was dissolved (18 ml added total). The saturated solution was allowed to slowly cool, and gradual white crystal formation was observed. Recrystallized product was collected once more by suction filtration with the Hirsch funnel once crystallization ceased. Collected product dried on a watch glass for a week, weighed 0.14 g (1.2 mmol), and the melting point was 139°-141°

In order to isolate benzoic acid, benzocaine and 9-fluorenone, each component needed to be separated from one another. All three compounds began together in one culture tube, dissolved in methylene chloride and formed into a homogenous mixture. In this culture tube, two milliliters of aqueous three molar hydrochloric acid was added, which immediately formed two layers, the top acidic aqueous layer was clear in color and contained benzocaine, and the bottom organic formed was yellow and contained benzoic acid and 9-fluorenone. Benzocaine’s amino group is protonated by the aqueous layer hydronium. This protonation forms the conjugate acid of benzocaine, benzocaine hydrochloride. Thus, the conjugate acid, benzocaine hydrochloride is a salt in which is soluble in water and furthermore can be isolated from the organic mixture. When testing out the pH levels in benzocaine, the pH test strip was dark blue in color, indicating a pH level of around 5 to 7. When isolating benzoic acid, two milliliters of aqueous three molar sodium hydroxide was added, which deprotonates the carboxylic group in benzoic acid, forming its conjugate base, sodium benzoate. As with benzocaine hydrochloride, sodium benzoate is a water soluble ionic salt in the aqueous layer that can then be separated from the bottom organic layer containing the 9-fluorenone. The pH test strip was a vibrant red for benzoic acid, indicating a pH of 2. Now the 9-fluorenone is left, deionized water is added to remove any excess

The wet, crude product was placed into the 50 mL Erlenmeyer flask. Small amounts of CaCl2 were added to dry the solution. The flask was sealed and the mixture was swirled and left to settle. Once

After dissolving benzoic acid in 1.0mL CH2Cl2 and 1.0mL 10% NaHCO3 solution, two layers are created, the top layer is 10% NaHCO3 solution and the bottom is CH2Cl2.

organic compounds. The goal of this technique is to allow organic compounds to form crystal

The week after, a recrystallization was performed on the previous week’s crude product. The product ethereal solution was first heated on a steam bath until dry. During the heating, a beaker of methanol was collected and also placed on the steam bath. Once the product was dry, it was cooled to room temperature and then placed in an ice-water bath. The now boiling methanol was added to the crude crystals and a recrystallization was performed. Once completed, the now purified product was collected via Buchner vacuum filtration and stored in drawer to dry for a week. Afterwards, a melting point range of the purified product was obtained by using a Mel-temp apparatus. Lastly, an

The crude solid was dissolved in hot ethanol and then, was allowed to cool. As the solution cooled the solubility of the compounds in the solution drops, which allowed the nitroacetanilide to recrystallize from the solution. The size of the crystals depends on the rate of cooling; a slower cooling rate leads to the formation of larger crystals. In order to collect the crude solid and the recrystallized solid, vacuum filtration was used. Vacuum filtration uses reduced pressure to force the solution and air through the filter paper, allowing for the solid to

The purpose of this experiment is to separate a mixture of salicylic acid and naphthalene using extraction, recrystallization and sublimation techniques. Extraction is the separation of compounds from a mixture based on their relative solubilities in different solvents. Sublimation is the process of separation by which a substance transitions from the solid phase into the gas phase, skipping the liquid phase. Recrystallization involves dissolving a substance in an appropriate solvent then crystallizing it as it cools (impurities remain in solution). The melting points of the substances were determined in order to assess their purity and the percent recovery of pure naphthalene and salicylic acid were calculated. According to the results, the melting point of pure naphthalene was between 86°C -89°C range, whereas for pure salicylic acid was 167°C -170°C. Both determined melting points were higher compared to the literature value of 80.26°C and 158.6°C for pure naphthalene and salicylic acid respectively. Lastly, the percent recovery for pure naphthalene and salicylic acid were 17.7% and 71.2% accordingly.