Oil Change Essay

pressure area becoming worse due to neglet or wrong information. Each shift needs to be aware of the plan of

That is how you change your oil a simple process that saves you money and keeps your car running for as long as you need

iii. The oil should roughly take ten to fifteen minutes to drain completely. When the oil stops draining your ready to remove the oil filter. Just like before with the plug place the oil drain pan directly under oil filter. This is done because almost always their will still be a little left over oil in the filter. When removing the filter you want to turn the oil filter counter clockwise to release it from your vehicle.

the oil cap and start the engine. Run the engine for 30 seconds or so to circulate the new oil, then

Once you have the car in the air you will want to put some jack stands under each side and lower the car down on these, this will prevent the car from falling on you if the jack where to collapse, since jacks are only designed to pick the car up, not support it all day. Once the car is safely on the jack stands, you are ready to change the oil.

i. Step 1: Locate the oil filler cap on top of the engine. Remove it.

Oil lubricates the moving parts that are within the engine. It also absorbs heat so that the engine doesn’t overheat. Your oil needs to be changed every 3,000 to 5,000 miles. If you would rather change it yourself instead of taking it in somewhere to be done, follow these steps.

The reconstructing of the car is important because it will let you know if the oil change was done successfully. Checking the new oil level is crucial to determining if the oil change was done right or not. Start the car and let it run for five minutes, but make sure the engine oil cap is back on so oil does not spew everywhere. When the car is turned off, use the oil dipstick, which is in the engine bay, to check the oil level. If the stick reads that the level is good, the oil

6.     Check in after 10 minutes, if you don?t see anymore oil dripping out, screw the nut back in tightly and also screw on the new oil filter. Using a little bit of motor oil on the rubber gasket will ensure a tight fit.

There are a few basic elements of an oil change, starting with draining the old oil from your engine and replacing it with new oil. Automotive technicians will also replace both the oil filter and the air filter in your vehicle. Each of these steps prevents damaging build-up of debris and helps keep your engine running with the least amount of wear and tear possible.

There are two more very important tasks to be done before the actual oil change process. The first is spreading a polythene sheet under your car engine so that the floor may not be greasy by the spilling of oil during the process and the second is grabbing a chair or a table near your car engine to keep the tool kit consisting of a wrench set, a rubber mallet, a box-end wrench for the plug, jack stand, funnel, paper towel, rubber gloves and a pan to trickle old oil in so that they can be made readily available when needed. Now keep the car jack right in the front center of the car and jack it up. Always remember to support the jack with a stand so that it doesn’t fall on you while you work underneath. It is risky to work under a car supported only with a jack. Then lower it down to the level you are convenient at while working underneath the car easily. Make sure that your car is set in the parking mode. Once the car is lifted up, put your safety glasses and rubber gloves on as the oil coming out of the car can be very hot. As mentioned earlier you should let the car run for a few minutes if it is cold so that it can get warmer and the sludge trickles down easily. Running car for about ten minutes before changing oil is recommended by many car experts. Unplug the drain

As the owner of the vehicle, you will most likely know your car or truck fairly well and can tell when something is not right. Some problems are easily fixed, and others are not, but depending on what is wrong, it is something that could have been avoided. This is actually a common occurrence when people have failed to get regular oil changes, as changing your oil can prevent extensive damage to your engine and much more.

Lube and oil changes are simple processes. The technician will get under your truck, remove the plug and let the liquid drain from the vehicle. Once it is empty, the technician will reinstall the plug and refill the engine with clean lubricant. At this time, the filter should also be changed in order to keep your truck running smoothly. The filter is what helps collect some of sludge buildup and keep the substance cleaner for longer.

An experienced mechanic can flush the engine. When the engine is flushed, the cleaner fluid will reduce the friction. The vehicle will move with less resistance, and the car will perform at an optimal level. When you get the oil changed at the recommended intervals, you can prevent larger problems from arising in the future.

It is advisable to choose your tire changing place very carefully. You should drive slowly to the next exit ramp so that you can stay away from main flow of traffic as you change your tire. Sometimes the line separating the traffic from you is not an invisible force field. Sometimes the car is left leaning leaving insufficient room. In this case you will need a level solid surface in order to jack up a car safely.