Panacetin Lab Report

Instead of approximately 28 mL of water being added, 140 mL of water was added. To correctly identify the compound, it was concentrated with nitrogen while the container was placed in a boiling water bath. After being concentrated enough, the experiment was able to continue. To confirm that the unknown was acetanilide, a comparison of the melting points between the acetanilide, phenacetin and the unknown was performed which led to confirming that the unknown was

Aspirin, Caffeine and Salicylamide were extracted from an over-the-counter pain reliever (BC Powder). These components were separated by manipulating their solubilities by adjusting the acidity and basicity of the solution. By doing this, the three components were forced into conjugate acid (or base) forms, causing selective solubility in either an aqueous or organic solvent. These layers were then separated by use of a separation funnel. Once separated, the components extracted were characterized by measuring the melting point and performing a TLC analysis. Also, the recovered aspirin from the first part of the experiment was recrystallized and compared to that of the

In experiment two, the drug Panacetin was separated by a series of chemical reactions into its three components: sucrose, aspirin, and an unknown active ingredient, either acetanilide or phenacetin. The purpose of this lab was to determine what percentages of each component is present in the pain-killer. The initial step was to dissolve Panacetin in dichloromethane. However, sucrose is insoluble in dichloromethane because organic molecules are soluble in organic solvents, and dichloromethane is an inorganic solvent, so only aspirin and the unknown dissolved. By using gravity filtration, sucrose was filtered from the solution and 0.30g of solid was collected.

Moisten filter paper with a few drops of solvent and turn on water vacuum to fullest extent

The recrystallization technique utilizes the ability of a compound to dissolve within a hot solvent and produce a solution. As this solution cools, the solute reforms without impurities in a crystal lattice structure.1 For this to work properly, an appropriate solution that will not dissolve the solute at low temperatures, but will at high temperatures, must be used.1 There is no single solvent that will work well for every solute’s recrystallization; different solvents are better suited for some solutes than others.2 Some impurities that do not dissolve within the solvent can be filtered out while the solution is still hot, while other impurities that readily dissolve within the solvent shouldn’t recrystallize with the pure substance (as they are not concentrated enough to

Panacetin is an analgesic (pain reducing) and antipyretic (fever reducing) drug that is sold in drug stores. However, there is a suspicion that this bottle may be counterfeit, not containing the chemicals that it should. Panacetin should be made up of about 50 percent of the unknown component that we previously separated out of Panacetin for testing. We suspect that this unknown compound is either acetanilide or phenacetin, both of which can be toxic to humans. It is very important that this component is

The mole is a convenient unit for analyzing chemical reactions. Avogadro’s number is equal to the mole. The mass of a mole of any compound or element is the mass in grams that corresponds to the molecular formula, also known as the atomic mass. In this experiment, you will observe the reaction of iron nails with a solution of copper (II) chloride and determine the number of moles involved in the reaction. You will determine the number of moles of copper produced in the reaction of iron and copper (II) chloride, determine the number of moles of iron used up in the reaction of iron and copper (II) chloride, determine the ratio of moles of iron to moles of copper, and determine the number of atoms and formula units involved in

The vial was removed from the heat and cooled to room temperature. The spin vane was rinsed with 2-3 drops of warm water over the conical vial. The vial was cooled to room temperature then placed in an ice bath for 15 minutes. The liquid was decanted from the mixture and the resulting crystals were dried on filter paper. The crystals were then placed on a watch glass for further drying. The crystals were weighed and a small sample was placed into a capillary tube for melting point determination.

This experiment involved three steps: synthesis of aspirin, isolation and purification, and the estimation of purity of the final product. The synthesis involved the reaction of salicylic acid and acetic anhydride in the presence of a catalyst, phosphoric acid, H3PO4. When the aspirin was prepared, it was isolated and filtered. The percentage yield of the synthesis was calculated to be 78.42%. The experimental melting point range of aspirin was determined to be 122 -132°C. Due to its wide range, and lower value than that of the theoretical melting point of 136°C, it was

21) After all of the solid dissolves, move the flask from the hot plate and allow it cool to room temperature. After a while, crystals should appear in the flask.

The product was then suspended in 2 ml of water with a stir rod in a 50 ml Erlenmeyer flask and heated to boiling. Water was added in one milliliter increments until all the product was dissolved (18 ml added total). The saturated solution was allowed to slowly cool, and gradual white crystal formation was observed. Recrystallized product was collected once more by suction filtration with the Hirsch funnel once crystallization ceased. Collected product dried on a watch glass for a week, weighed 0.14 g (1.2 mmol), and the melting point was 139°-141°

The purpose of this lab is to investigate the composition of a compound suspected to be Panacetin, a type of pain-killer. Panacetin is typically made up of sucrose, aspirin, and acetaminophen, but the third component in this experiment is unknown. The unknown component is suspected to be a chemical relative of acetaminophen, either acetanilide or phenacetin. Using techniques such as extraction, evaporation, and filtration, the three components will be isolated based on their solubilities and acid-base properties. Then, the percent composition of Panacetin can be deduced based on the masses of the three dried components. The

Of the three components likely to be present in your sample of Panacetin (aspirin, acetanilide, and starch), only starch is insoluble in the organic solvent dichloromethane (or methylene chloride), CH2 Cl2. If a sample of Panacetin is dissolved as completely as possible in dichloromethane, the insoluble starch can be filtered out, leaving acetanilide and aspirin in solution. The purpose of this experiment is to extract the components of Panacetin.

An ice bath was prepared in a large beaker and a small cotton ball was obtained. 0.5 g of acetanilide, 0.9 g of NaBr, 3mL of ethanol and 2.5 mL acetic acid was measured and gathered into 50mL beakers. In a fume hood, the measured amounts of acetanilide, NaBr, ethanol and acetic acid were mixed in a 25mL Erlenmeyer flask with a stir bar. The flask was plugged with the cotton ball and placed in an ice bath on top of a stir plate. The stir feature was turned on a medium speed. 7mL of bleach was obtained and was slowly added to the stirring flask in the ice bath. Once all the bleach was added, stirring continued for another 2 minutes and then the flask was removed from the ice bath and left to warm up to room temperature. 0.8mL of saturated sodium thiosulfate solution and 0.5mL of NaOH solution were collected in small beakers. The two solutions were added to the flask at room temperature. The flask was gently stirred. Vacuum filtration was used to remove the crude product. The product was weighed and a melting point was taken. The crude product was placed into a clean 25mL Erlenmeyer flask. A large beaker with 50/50 ethanol/water

Crystals were collected in a Buchner funnel, washed with alcohol, then ether, then transferred into a sample tube for storage.