Photochemical Synthesis of Benzopinacol and Its Acid-Catalyzed Rerrangement Product Benzopinacolone

After placing in darkness the colorless solution resulted by reformation of the radical intermediates to a new thermodynamic product via C-N bond at room temperature. UV-Vis was conducted on the solution before and after the irradiation with sunlight: UVtoluene 554.92nm, A=0.12 before irradiation and A=1.05 after. The peak at 554.92nm corresponds to yellow/green light and its complementary colour is red/violet. This validates the solutions violet color. The increased absorbance was accounted for an increase in the radical component. The radical was formed when exposed to light, which was visually apparent with the purple coloration and proved the thermodynamic dimer was also photochromic. When dimer 4 is exposed to light photons collide with the molecule and impart energy upon them. This energy is significant enough to break the bond between the two rings and results

The purpose of this experiment was to synthesize the Grignard reagent, phenyl magnesium bromide, and then use the manufactured Grignard reagent to synthesize the alcohol, triphenylmethanol, by reacting with benzophenone and protonation by H3O+. The triphenylmethanol was purified by recrystallization. The melting point, Infrared Spectroscopy, 13C NMR, and 1H NMR were used to characterize and confirm the recrystallized substance was triphenylmethanol.

The hydrobenzoin (meso) product of the benzil was isolated through the techniques of recrystallization and vacuum filtration. Because there NaBH4 was the limiting reagent in the experiment, 0.005604moles of NaBH4 should yield 1.2008g of hydrobenzoin (meso). The mass of the isolated product was 0.613g, resulting in a 51.1% yield. There are many reasons to account for the loss of 48.9% of

In order to isolate benzoic acid, benzocaine and 9-fluorenone, each component needed to be separated from one another. All three compounds began together in one culture tube, dissolved in methylene chloride and formed into a homogenous mixture. In this culture tube, two milliliters of aqueous three molar hydrochloric acid was added, which immediately formed two layers, the top acidic aqueous layer was clear in color and contained benzocaine, and the bottom organic formed was yellow and contained benzoic acid and 9-fluorenone. Benzocaine’s amino group is protonated by the aqueous layer hydronium. This protonation forms the conjugate acid of benzocaine, benzocaine hydrochloride. Thus, the conjugate acid, benzocaine hydrochloride is a salt in which is soluble in water and furthermore can be isolated from the organic mixture. When testing out the pH levels in benzocaine, the pH test strip was dark blue in color, indicating a pH level of around 5 to 7. When isolating benzoic acid, two milliliters of aqueous three molar sodium hydroxide was added, which deprotonates the carboxylic group in benzoic acid, forming its conjugate base, sodium benzoate. As with benzocaine hydrochloride, sodium benzoate is a water soluble ionic salt in the aqueous layer that can then be separated from the bottom organic layer containing the 9-fluorenone. The pH test strip was a vibrant red for benzoic acid, indicating a pH of 2. Now the 9-fluorenone is left, deionized water is added to remove any excess

Abstract: Using hypochlorous acid to convert secondary alcohol called cyclododecanol to the corresponding ketone which is cyclododecanone by oxidation.

Purpose: The purpose of this experiment is to observe a variety of chemical reactions and to identify patterns in the conversion of reactants into products.

1. Purpose: to clarify the mechanism for the cycloaddition reaction between benzonitrile oxide and an alkene, and to test the regiochemistry of the reaction between benzonitrile oxide and styrene.

This experiment was designed by conducting a substitution reaction to construct a complex compound (2-methylphenoxyacetic acid) from two simple parts; also known as synthesis - converting simple molecules into more complex molecules. A purification technique known as crystallization was used to purify the product. Suction filtration was used to filter out the product. The experiment was completed over a three-day experimental period.

The very word, photo “synthesis” gives away what kind of reaction it is…a synthesis reaction. In this case, you have two products ( ) in the presence of light energy

In this laboratory experiment a synthesis was performed through several separate steps. The purpose of the experiment was to synthesize tetraphenylcyclopentadienone from benzaldehyde and to run reactions on carbonyl containing compounds. There was a total of three steps that led up to the synthesis of the final product, tetraphenylcyclopentadienone. The first step of the experiment was the condensation of benzaldehyde to yield benzoin. Thiamine catalyst along with water and ethanol were added to the benzaldehyde, then NaOH was added until the solution turned yellow. After recrystallization, the product was benzoin. Step two was the oxidation of benzoin to benzil.

Hickey) Organic chemistry lab 2 manual, department of Chemistry University of New Orleans. We observed a yellow residue in the bottom of the flask after the dichloromethane has been boiled off, and 2-propanol (3ml) was added to it and then was heated until the entire residue dissolved and the solution was transferred to a clean Erlenmeyer flask.

Chemical synthesis is an imperative technique most relevant to organic chemists. Synthesis employs a succession of chemical reactions by using pre-existing structures to make new and functional ones. A combination of lab techniques could be developed in order to synthesize and attain the desired product. This particular experiment calls for the use for reflux, extraction, recrystallization, infrared spectroscopy, and melting point analysis. The overall objective of this lab is to utilize these steps to synthesize acetaminophen from p-aminophenol and characterize it .

In this preparative lab, an aldol (trans-p-anisalacetophenone) was produced from the reaction between p-anisaldehyde and acetophenone with the presence sodium hydroxide. The reaction also showed the importance of an enolate and the role it played in the mechanism. Sodium hydroxide acts as a catalyst in this experiment and is chosen because of its basic conditions and pH. The acetophenone carries an alpha hydrogen that has a pKa between 18 and 20. This alpha hydrogen is acidic because of its location near the carbonyl on acetophenone. When the sodium hydroxide is added, it deprotonates the hydrogen and creates an enolate ion. This deprotonation creates a nucleophilic carbon that can attack an electrophilic carbon (like a parent

Through the use of the Grignard reaction, a carbon-carbon bond was formed, thereby resulting in the formation of triphenylmethanol from phenyl magnesium bromide and benzophenone. A recrystallization was performed to purify the Grignard product by dissolving the product in methanol. From here, a melting point range of 147.0 °C to 150.8 °C was obtained. The purified product yielded an IR spectrum with major peaks of 3471.82 cm-1, 3060.90 cm-1, 1597.38 cm-1, and 1489.64 cm-1, which helped to testify whether the identity of the product matched the expected triphenylmethanol. The identity of the product being correct was further confirmed by way of both proton and carbon-13 NMR spectra. This is due to the fact

After the initial mixture has refluxed, 9.11 grams of benzophenone was dissolved in 100 mL of anhydrous ether in a beaker and was then transferred into the separatory on the reflux apparatus. This solution was then added to the Grignard reagent at a drop wise rate while stirring. After the benzophenone was added, the mixture was then refluxed for 15 minutes on a heating mantle.