Preparation and Recrystallisation of Aspirin

An Erlenmeyer flask was used to accommodate the largest volume of recrystallization solvent calculated and was cooled in an ice bath to increase the yield of crystals. The solid was collected by vacuum filtration and washed with a small amount of ice water. The product is then dried to a constant mass by use of an oven and weighed. A small amount of the unknown was compared to two samples of acetanilide and phenacetin for a melting point range to determine the identity. The temperature of the unknown was recorded when the first trace of liquid can be seen and when the unknown was completely liquid.

had formed, they were collected by vacuum filtration and weighed. A small amount of the crystals were no weighed due to a lack of toluene with which to rinse the 50 mL Erlenmeyer flask of the last of the crystals.

The goal of the experiment was to securely isolate pure acetaminophen from p-aminophenol using a synthesis reaction. Synthesis still remains an important tool for scientists conducting chemical reactions. Most synthesis relies on a long process that involves multiple chemicals reactions. In the synthesis of Acetaminophen, one reaction is performed and a four step process is used, Scheme 1. Multiple techniques was used to achieve this goal.

In experiment two, 1.48g of the unknown solid was recovered. From this mass, it was determined approximately 30mL of boiling water was needed for crystallization of acetanilide and about 121mL for phenacetin. Phenacetin would require more solvent because it is less

The product was placed in a Craig tube and several drops of hot (100°C) solvent (50% water, 50% methanol, by volume) was added and heated until all of the crystals dissolved. The Craig tube was plugged and set in an Erlenmeyer flask to cool. Crystallization was induced once the mixture was at room temperature by scratching the inner wall of the tube. It was then placed into an ice bath for ten minutes until crystallization was complete. The tube was then

3.0g of salicylic acid was weighed then 3.0mL of acetic anhydride and 6 drops of 85% H3PO4 were added to it. The mixture was warmed over a water bath for 5 minutes while stirring. After warming, 20 drops of distilled water was slowly added. 15mL of water was added then the solution was heated until it became clear. It was allowed to cool and was placed in an ice bath until the solution becomes cloudy. Using pre-weighed filter paper, the mixture was filtered and was allowed to dry in the filter paper.

The product was then suspended in 2 ml of water with a stir rod in a 50 ml Erlenmeyer flask and heated to boiling. Water was added in one milliliter increments until all the product was dissolved (18 ml added total). The saturated solution was allowed to slowly cool, and gradual white crystal formation was observed. Recrystallized product was collected once more by suction filtration with the Hirsch funnel once crystallization ceased. Collected product dried on a watch glass for a week, weighed 0.14 g (1.2 mmol), and the melting point was 139°-141°

Industrial production of Aspirin is dependent on the company producing the drug; however the general method of production is known as slugging or dry-granulation. In this method, corn starch is mixed with pure water and is then heated and

Pre-Lab: Analgesic drugs are known for reducing pain, while antiseptic drugs reduce symptoms such as fevers and swelling. However, some of these drugs can reduce both illnesses. To obtain a pure compound in these drugs, the scientist needs to separate the desired compound by taking advantage of the different physical and chemical properties. Such as; different boiling points, melting points and their solubility properties. To do this a chemist can also asses the differences between acidic and basic substances when they are added to water soluble mixtures. Within this current experiment I will asses the

I hypothesize that salicylic acid will react with acetic anhydride to produce acetylsalicylic acid (aspirin) and acetic acid (vinegar).

The crude product was washed by taking the reaction product in the separatory funnel and adding 23 mL of deionized H2O. The mixture was shaken and allowed to settle until layers were observable. The top layer was the desired product and approximately 25 mL of aqueous layer was extracted from the separatory funnel. Next, 25 mL of 5% NaHCO3 was added to the separatory funnel in order to neutralize the acid. This mixture was swirled, plugged with the stopper and inverted. Built-up gas was released by turning the stopcock to its opened and closed positions, releasing CO2 by-product. This was done four times in one minute intervals. The solution was allowed to settle until layers were observable. The bottom layer that contained salt, base and water was extracted from the separatory funnel. The crude product was washed again as mentioned previously.

This experiment was designed by conducting a substitution reaction to construct a complex compound (2-methylphenoxyacetic acid) from two simple parts; also known as synthesis - converting simple molecules into more complex molecules. A purification technique known as crystallization was used to purify the product. Suction filtration was used to filter out the product. The experiment was completed over a three-day experimental period.

The reaction took place in a conical vial and .2mL of each of the reactant samples were added to it along with some 95% ethanol. Two drops of NaOH were added shortly after and stirred at room temperature for fifteen minutes. The vial was cooled in and ice bath and crystallized. Vacuum filtration was performed to filter the crude product. The crude product was recrystallized using methanol and filtered again. We made one change to the procedure and instead of using .7mL of ethanol we

As the acid was being added, the mixture was being stirred over a stir plate. Once completed, the reaction mixture was poured from the round bottom flask into a 500 mL separatory funnel and its top (organic) layer was extracted into another beaker. The bottom (aqueous) layer was placed back into the funnel and extracted twice with 50.0 mL of ethyl ether each. The newly extracted layers were combined and dried over magnesium sulfate (MgSO4). The dried solution was the decanted into a beaker to remove the MgSO4 salts and the product solution was collected via Buchner vacuum filtration. The resulting product was transferred into an Erlenmeyer flask with an inverted beaker on top and stored in a drawer.

Once cooled, the mixture was then transferred to a separatory funnel using the funnel while avoiding adding the boiling chip. 10 ml of water was then added to the mixture. The mixture was gently shaken and the phases were allowed to separate. The funnel was then unstopped and the lower aqueous phase was drained into a beaker. 5 ml of 5% aqueous NaHCO3 was added and then shaken gently. A great deal of caution was taken into consideration because of the production of carbon dioxide gas which caused pressure to develop inside the funnel. The pressure needed to be released so the funnel was vented frequently. The phases were allowed to separate and the lower aqueous phases was drained into the beaker. After draining, 5 ml of saturated NaCl was added to the funnel and then shaken gently. Once again, the phases were allowed to separate and the lower aqueous phase was drained into a beaker. An ester product was produced and was transferred into a 25 ml Erlenmeyer flask. This organic product was then dried over anhydrous Na2SO4 to trap small amounts of water in its crystal lattices thus removing it from the product. Finally the ester was decanted, so that the drying agent was excluded from the final product.