Preparation of Cyclohexanol

The objective of this lab was to create a ketone through an oxidation reaction using a using a secondary alcohol and oxidizing agent in order to use that ketone in a reduction reaction with a specific reducing agent to determine the affect of that reducing agent on the diastereoselectivity of the product. In the first part of this experiment, 4-tert-butylcyclohexanol was reacted with NaOCl, an oxidizing agent, and acetic acid to form 4-tert-butylcyclohexanone. In the second part of this experiment, 4-tert-butylcyclohexanone was reacted with a reducing agent, either NaBH4 in EtOH or Al(OiPr)3 in iPrOH, to form the product 4-tert-butylcyclohexanol. 1H NMR spectroscopy was used to determine the cis:trans ratio of the OH relative to the tert-butyl group in the product formed from the reduction reaction with each reducing agent. Thin-layer chromatography was used in both the oxidation and reduction steps to ensure that each reaction ran to completion.

Different procedures were used to isolate benzil from the ether layer and benzoic acid from the aqueous layers. To isolate benzil, anhydrous MgSO4 was added to the flask containing the ether layer solution. MgSO4 removes the remaining water in the ether layer solution. After making sure that enough amount of MgSO4 present in the solution, the ether solution was filtered by using gravity filtration. During filtration, MgSO4 was removed from the solution and the ether solution was collected in 25 ml flask. To separate benzil from the filtered ether solution, the beaker containing the ether solution was heated until the ether evaporated. After letting the beaker to cool to room temperature, the mass of the beaker with the benzil crystals was measured. From the combined mass of the beaker and the benzil crystals and from the predetermined mass of the beaker, the mass of the collected crystals was calculated to be 0.266 gram.

This way, cyclohexane is converted to adipic acid or hexanedioic acid. Since the product is soluble in hot water, the two-phase systems (organic cyclohexane and aqueous hydrogen peroxide) slowly become a single aqueous phase. In the end, only H2O2 and cyclohexene can be changed, tungstate and the phase transfer catalyst can be tapped and reused. The phase transfer catalyst used were a mixture of aliquat 336 and potassium hydrogen sulphate.

Alcohol dehydrations are widely used in many industries to produce alkene. In this experiment 2-methylcyclohexanol was dehydrated to three possible products using phosphoric acid as a catalyst. The main tool for this experiment is the Hickman still. First, Drierite was added to the Hickman still so that any excess water formed during the experiment will be absorbed. It also acted as a boiling stone and addition surface to increase surface area. Next, 0.75 mL of 2-methylcyclohexanol is added to the still and right after 1 mL of phosphoric acid is added. The phosphoric acid (H3PO4) acts as a catalyst in order for the reaction to occur. The mixture is heated up to between 120o Celsius and 160o Celsius. If the temperature goes above 165oC then

Whereas for simple distillation, the compounds need to be around 80C apart in order for proper separation to occur. Thus, cyclohexane and toluene were not able to be properly separated since the boiling point for cyclohexane was 80.74C while the boiling point of toluene was 110.6C—there two boiling points are fairly close to one another. Thus, the mole fraction for cyclohexane and toluene were fairly low when compared to cyclohexane and

We used TLC analysis to identify each product obtained from the dihydroxylation reactions by spotting a TLC plate with the product of our reaction, a solution of cis-cyclohexane, trans-cyclohexane, and a 50:50 mixture of the two. We then placed the plate in a beaker with ethyl acetate saturating the atmosphere to allow the TLC plate to develop. Finally, we compared Rf values of the components of the mobile phase, after the phase was completed. 100% ethyl acetate was used instead of 100% Hexane or a mixture of Ethyl Acetate, because ethyl acetate has high polarity and can separate the components of a mixture to elution, unlike hexane, which is non-polar, and therefore unable to separate the components of the mixture. A 50:50 mixture of both would not work, because the polar and non-polar compounds would neutralize the mixture, and thereby not separate the components of the mixture.

The purpose of this experiment was to practice the functional group transformation procedure. The process of the experiment included the dehydration of 2-methylcyclohexanol in the presence of phosphoric acid and heat. The products that were formed from the reaction were 1-methylcyclohexene and 3-methylcyclohexene. The mass of the final product solution was 0.502g with a percent yield of 18.7% and a boiling point range of 84.5-98.5oC.

Working in the hood or a designated work area, add about 1 mL of ethyl alcohol to a clean evaporating dish. Place the evaporating dish on a heat- resistant pad.

6. Purpose: to clarify the mechanism for the cycloaddition reaction between benzonitrile oxide and an alkene, and to test the regiochemistry of the reaction between benzonitrile oxide and styrene; to purify the crude product of either trans-stilbene, cis-stilbene, or styrene reaction.

In this experiment, 0.31 g (2.87 mmol) of 2-methylphenol was suspended in a 10 mL Erlenmeyer flask along with 1 mL of water and a stir bar. The flask was clamped onto a hotplate/stirrer and turned on so that the stir bar would turn freely. Based on the amount of 2-methylphenol, 0.957 mL (0.00287 mmol) NaOH was calculated and collected in a syringe. The NaOH was then added to the 2-methylphenol solution and allowed to mix completely. In another 10 mL Erlenmeyer flask, 0.34 g (2.92 mmol) of sodium chloroacetate was calculated based on the amount of 2-methylphenol and placed into the flask along with 1 mL of water. The sodium chloroacetate solution was mixed until dissolved. The sodium chloroacetate solution was poured into the 2-methylphenol and NaOH solution after it was fully dissolved using a microscale funnel.

The purpose of this lab was to carry out a dehydration reaction of 2-methylcyclohexanol by heating it in the presence of phosphoric acid and determining which alkene product would be the major product. Methylcyclohexanols were dehydrated in an 85% phosphoric acid mixture to yield the minor and major alkene product by elimination reaction, specifically E1. The alkenes were distilled to separate the major and minor products and gas chromatography was used to analyze the results and accuracy of the experiment. The hypothesis was the major product of the reaction would be the most substituted product. This conclusion was made because of

Hickey) Organic chemistry lab 2 manual, department of Chemistry University of New Orleans. We observed a yellow residue in the bottom of the flask after the dichloromethane has been boiled off, and 2-propanol (3ml) was added to it and then was heated until the entire residue dissolved and the solution was transferred to a clean Erlenmeyer flask.

3. The spectrophotometer was set at 420nm. Distilled water was also used as the ‘blank’.

The week after, a recrystallization was performed on the previous week’s crude product. The product ethereal solution was first heated on a steam bath until dry. During the heating, a beaker of methanol was collected and also placed on the steam bath. Once the product was dry, it was cooled to room temperature and then placed in an ice-water bath. The now boiling methanol was added to the crude crystals and a recrystallization was performed. Once completed, the now purified product was collected via Buchner vacuum filtration and stored in drawer to dry for a week. Afterwards, a melting point range of the purified product was obtained by using a Mel-temp apparatus. Lastly, an

The purpose of this lab was to synthesize the ester isopentyl acetate via an acid catalyzed esterification (Fischer Esterification) of acetic acid with isopentyl alcohol. Emil Fischer and Arthur Speier were the pioneers of this reaction referred to as Fischer Esterification. The reaction is characterized by the combining of an alcohol and an acid (with an acid catalyst) to yield and ester plus water. In order to accomplish the reaction, the reactants were